Uploaded April 2017 | Updated November 2026, 4 hours ago
A while ago we purchased a bottle of Molybdenum(VI)oxide. Since then we were trying to reduce it to the Mo(V) compound Molybdenum Blue wish is said to be good way to test for Mo. Although we tried various reducing agents, reaching from Borohydrides to Aluminiumhydrides (which works, video follows, soon), our preferred method to reduce compounds with Aluminium in HCl and even converting it to the Molybdate first and then trying all these methods always resulted in lower brown oxidation states.
Then we discovered a very old method to test for certain metals, reducing them by fusing their compounds with elemental Sodium.
So here is our first try, MoO3 + Na heated till the sodium ignited by itself and then leached out with water.
So what is happening here?
First of all you can see how the MoO3 changes to yellow once heated as the compound is thermochromic much like ZnO. Then you can see that the surface close to the sodium starts to become blue before the sodium ignites.
The overall reaction seems to be connected to what happens in a thermite reaction.
We are still unsure how the oxidation state is determined here.
A while ago we purchased a bottle of Molybdenum(VI)oxide. Since then we were trying to reduce it to the Mo(V) compound Molybdenum Blue wish is said to be good way to test for Mo. Although we tried various reducing agents, reaching from Borohydrides to Aluminiumhydrides (which works, video follows, soon), our preferred method to reduce compounds with Aluminium in HCl and even converting it to the Molybdate first and then trying all these methods always resulted in lower brown oxidation states.
Then we discovered a very old method to test for certain metals, reducing them by fusing their compounds with elemental Sodium.
So here is our first try, MoO3 + Na heated till the sodium ignited by itself and then leached out with water.
So what is happening here?
First of all you can see how the MoO3 changes to yellow once heated as the compound is thermochromic much like ZnO. Then you can see that the surface close to the sodium starts to become blue before the sodium ignites.
The overall reaction seems to be connected to what happens in a thermite reaction.
We are still unsure how the oxidation state is determined here.
 from PdCl2
We mentioned in another video that we werent sure about what product might form if PdCl2 reacted with KCN. After a big search in old literature, we found a line that proves the formation of Tetracyanopalladate(II) if KCN is added to PdCl2 or [PdCl4](2-). And as you can see once we add it the brown color disappears. Palladium Chemistry: [Pd(CN)4](2-) from PdCl2](https://i.ytimg.com/vi/XHbn9Z3EaAA/mqdefault.jpg)




![Titanium Chemisty: Titanium in HF [8x faster]
The preparations for this experiment started with us finding a line in an old chemistry textbook saying Ti would dissolve quite well in HF. As you probably know, it usually takes high temperatures and long periods until Ti dissolves in anything (check out our TiCl3 video for that). Therefore, we thought we could try this with HF, note the HF has around 40% concentration so around the HCl and the temperature was around 20°C when we did that so at cooler temperatures.
We filled a test tube with 5 ml of HF (40%) and added a small piece of Ti wire. The reaction started immediately quickly producing a purple - pink solution At some point, we added a bit of water. The color changes to green. In the end, you can see two layers, the upper one is the aqueous Ti-complex and the bottom one is insoluble [SiF6](2-).
The question is why does it react with HF better than with HCl? And we cant really find a suitable explanation. The fact that HF attacks glass is probably something different here. It could be because very stable Fluorocomplexes are formed. Elements like Zirconium, Titanium, even Iron are known to form stable Fluoride complexes although usually, Fluoride is a weak ligand. Titanium(III) and (IV) especially in acids also tends to form Titanyl, TiO2 and hydrated oxygen-rich species. So perhaps the equilibrium shifts towards the fluoride here because it resists the back-reaction to some extend and the passive layer is therefore destroyed.
And to be honest we have no clue what is happening in this experiment at all. Even the Gmelin does not really talk a lot about the chemistry between HF and Ti metal. According to other books, the following reaction is very likely:
Much like with HCl, HF dissolves the Ti to form Ti(III). For the chloro-species, there are many isomers much like with Chromium. While the [Ti(H2O)6]Cl3 and also the [Ti(H2O)6]F3 are said to be purple-red their isomer, [Ti(H2O)4Cl2]Cl is green. And we think this is the case for the fluoro complex as well.
The question remains why this happens here and not the other way around? What might happen is that the pure Hexaqua-complex acts as a cationic acid and is deprotanted as the conc. of H(+) from HF is diluted with the addition of water. Then the famous Titanium-Oxy and Hydroxy-species form and perhaps somewhere in this cycle Fluoride can take the positions.
If you find anything about the actual reaction we would be really interested to hear about it.
Also if you ask yourself why we think the colors here are purple and green. We ran this experiment twice before with different concentrations and it would always self-heat to a point where it got out of control producing much more intense colored compounds which were really deep purple and grass green. Titanium Chemisty: Titanium in HF [8x faster]](https://i.ytimg.com/vi/Z44cBRfHm_k/mqdefault.jpg)




