Uploaded June 2026 | Updated November 2026, 13 hours ago
Learn the seal-in logic that controls conveyor direction in the free ACC PLC Simulator â reverse on the right sensor, reset when the motor stops.
⥠QUICK ANSWER
In the ACC Simulator conveyor, direction control uses a seal-in (latch): the direction output is wired in parallel with itself, so once the box trips the right sensor and reverses, the direction stays reversed even after the box leaves the sensor. A normally-closed motor-run contact (Y1) sits in series with the seal-in branch, so when the motor stops the latch drops and the next cycle starts forward again. The complete rung-by-rung build â every contact, the full ladder, and the simulator scene to try yourself â is in the written guide.
đŽ TRY IT FREE + FULL STEP-BY-STEP (build it live in the ACC PLC Simulator)
accautomation.ca/plc-programming-tutorial-build-a-conveyor-system-acc-simulator
âļ WATCH THE FULL CONVEYOR BUILD
youtu.be/himbbHHZ6HM
đ WHAT YOU'LL LEARN
â Build a seal-in (latch) so conveyor direction holds after the box clears the right sensor
â Wire the direction output in parallel with itself to keep the reversed state
â Use a normally-closed motor-run contact (Y1) to reset direction when the motor stops
â Make the next cycle restart in the forward direction automatically
â Test the whole rung live in the free ACC PLC Simulator
â FREQUENTLY ASKED
Q: What is a seal-in circuit and why use it here?
A: A seal-in latches an output on by feeding it back in parallel with the trigger. Here it holds the conveyor's reversed direction after the box leaves the right sensor, instead of snapping back instantly.
Q: How does the direction reset for the next box?
A: A normally-closed motor-run contact in series with the seal-in branch breaks the latch when the motor stops, so the next cycle starts forward.
đ Full rung-by-rung build + the simulator scene: accautomation.ca/plc-programming-tutorial-build-a-conveyor-system-acc-simulator
đ MORE RESOURCES
âļ More tutorials + free PLC Simulator: accautomation.ca
âļ PLC Beginners Guide: accautomation.ca/programming/plc-beginners-guide
âļ Free eBooks: accautomation.ca (subscribe for download)
đ RECOMMENDED HARDWARE (optional â this builds in the free simulator)
âļ Shop: automationdirect.com
âļ Parts Guide: accautomation.ca/purchase-find-parts
đŦ Questions? Drop a comment below.
đ New tutorials every Monday â Subscribe and hit the bell!
#PLC #LadderLogic #IndustrialAutomation #PLCProgramming #ACCAutomation #PLCSimulator #ConveyorControl #SealInCircuit #MotorControl #PLCTutorial
Regards,
Garry
ACC Automation
accautomation.ca
Learn the seal-in logic that controls conveyor direction in the free ACC PLC Simulator â reverse on the right sensor, reset when the motor stops.
⥠QUICK ANSWER
In the ACC Simulator conveyor, direction control uses a seal-in (latch): the direction output is wired in parallel with itself, so once the box trips the right sensor and reverses, the direction stays reversed even after the box leaves the sensor. A normally-closed motor-run contact (Y1) sits in series with the seal-in branch, so when the motor stops the latch drops and the next cycle starts forward again. The complete rung-by-rung build â every contact, the full ladder, and the simulator scene to try yourself â is in the written guide.
đŽ TRY IT FREE + FULL STEP-BY-STEP (build it live in the ACC PLC Simulator)
accautomation.ca/plc-programming-tutorial-build-a-conveyor-system-acc-simulator
âļ WATCH THE FULL CONVEYOR BUILD
youtu.be/himbbHHZ6HM
đ WHAT YOU'LL LEARN
â Build a seal-in (latch) so conveyor direction holds after the box clears the right sensor
â Wire the direction output in parallel with itself to keep the reversed state
â Use a normally-closed motor-run contact (Y1) to reset direction when the motor stops
â Make the next cycle restart in the forward direction automatically
â Test the whole rung live in the free ACC PLC Simulator
â FREQUENTLY ASKED
Q: What is a seal-in circuit and why use it here?
A: A seal-in latches an output on by feeding it back in parallel with the trigger. Here it holds the conveyor's reversed direction after the box leaves the right sensor, instead of snapping back instantly.
Q: How does the direction reset for the next box?
A: A normally-closed motor-run contact in series with the seal-in branch breaks the latch when the motor stops, so the next cycle starts forward.
đ Full rung-by-rung build + the simulator scene: accautomation.ca/plc-programming-tutorial-build-a-conveyor-system-acc-simulator
đ MORE RESOURCES
âļ More tutorials + free PLC Simulator: accautomation.ca
âļ PLC Beginners Guide: accautomation.ca/programming/plc-beginners-guide
âļ Free eBooks: accautomation.ca (subscribe for download)
đ RECOMMENDED HARDWARE (optional â this builds in the free simulator)
âļ Shop: automationdirect.com
âļ Parts Guide: accautomation.ca/purchase-find-parts
đŦ Questions? Drop a comment below.
đ New tutorials every Monday â Subscribe and hit the bell!
#PLC #LadderLogic #IndustrialAutomation #PLCProgramming #ACCAutomation #PLCSimulator #ConveyorControl #SealInCircuit #MotorControl #PLCTutorial
Regards,
Garry
ACC Automation
accautomation.ca









![17 to 42 Instructions in One Week: The Free PLC Sim Just Leveled Up
The free ACC PLC Simulator now has 42 ladder instructions, online editing, a drum sequencer, pointers and shift registers. Runs in your browser, no install.
⥠QUICK ANSWER
PLC simulator online editing means changing a rung while the program keeps scanning, exactly as you would on a plant floor where stopping the line is not an option. Press run, click edit, and an amber bar appears while the scan continues. New rungs show green, changed rungs amber, deleted rungs stay as gray ghosts. Press accept and the edit is validated first, then swapped in between two scans with timers, counters and data carried over, and cancel puts everything back. Alongside it this release adds a drum sequencer with a per step time and event bit, 4000 data registers from D1 to D4000, indirect addressing with D[D2] pointers that show the resolved address live, shift registers, jumps, master control zones, edge contacts, retentive timers and system bits.
đ FULL WALKTHROUGH + EXAMPLES
https://accautomation.ca/free-plc-simulator-update-online-editing-drum-sequencer/
âļ RUN IT NOW, FREE IN YOUR BROWSER
https://accautomation.ca/simulator/
âąī¸ TIMESTAMPS
0:00 - Introduction
0:17 - Why the ACC PLC Simulator Is Free and Browser Based
0:33 - Online Editing While the Program Keeps Scanning
1:06 - Drum Sequencer Driving a Traffic Intersection
1:22 - Inside the Drum Step Table
1:35 - 4000 Data Registers and Math Instructions
1:54 - Indirect Addressing with D[D2] Pointers
2:24 - Shift Registers, Jumps and Master Control Zones
2:44 - Edge Contacts, Retentive Timers and System Bits
3:05 - Hover Help, F1 and Structured Text Snippets
3:27 - Try It: Load the Traffic Drum Example
đ WHAT YOULL LEARN
â
Edit a rung online while the program keeps scanning, then accept it between two scans
â
Read the colour code: green for new rungs, amber for changed, gray ghosts for deleted
â
Drive a whole traffic intersection from one drum sequencer and its step table
â
Point one instruction at any register with D[D2] and watch the address resolve live
â
Track parts down a conveyor with bit shift registers, and skip rungs with jump and label
â
Use first scan bits, clock pulses, scan time and the real-time clock from system words
â FREQUENTLY ASKED
Q: What happens to my timers and counters when I accept an online edit?
A: They are carried over. The edit is validated first, then swapped in between two scans, so running values and data survive the change.
Q: What does D[D2] actually mean?
A: It is indirect addressing. The instruction uses the register whose number is stored in D2, so changing D2 points the same instruction at a different register. The block shows the resolved address live.
Q: Do I need to install anything or create an account?
A: No. It runs in a browser, it is free, there is nothing to install and no account is needed.
Q: Can I see what a jump is skipping?
A: Yes. Skipped rungs are drawn dimmed, so you can see at a glance which blocks are not being solved, and master control zones show which outputs drop when the zone turns off.
đ Full walkthrough and examples: https://accautomation.ca/free-plc-simulator-update-online-editing-drum-sequencer/
đ MORE RESOURCES
âļ Free PLC Simulator: https://accautomation.ca/simulator/
âļ Series: https://accautomation.ca/series/
âļ PLC Beginners Guide: https://accautomation.ca/programming/plc-beginners-guide/
âļ Free eBooks: https://accautomation.ca (subscribe for download)
đ RECOMMENDED HARDWARE
âļ Shop: https://www.automationdirect.com/
âļ Parts Guide: https://www.accautomation.ca/purchase-find-parts/
đŦ Which instruction should get its own tutorial first? Drop a comment below.
đ New tutorials every Monday â Subscribe and hit the bell!
#PLC #LadderLogic #IndustrialAutomation #PLCProgramming #ACCAutomation #PLCSimulator #LearnPLC #PLCTutorial #FreeTraining
Regards,
Garry
ACC Automation
http://www.accautomation.ca 17 to 42 Instructions in One Week: The Free PLC Sim Just Leveled Up](https://i.ytimg.com/vi/_PJaUYQenfE/mqdefault.jpg)
