Uploaded November 2026 | Updated November 2026, 2 days ago
PLC start stop jog side by side: two rungs in ladder, two lines in structured text - the same circuit, and why ST's real advantage is not line count.
โก QUICK ANSWER
The same start, stop and jog circuit is two rungs in ladder and two lines in structured text:
Y1 := (X1 OR (Y1 AND NOT C1) OR X3) AND X2;
C1 := X3;
In ladder that is one rung carrying three parallel branches - start, the seal-in, and jog - in series with the normally closed stop contact, plus a second rung driving C1 from the jog input. So on size it is a draw, and anyone telling you structured text is automatically more compact has not counted. What actually differs is how you read it: ladder is a diagram you trace with your eye, structured text is one expression you read left to right. The real structured text advantage shows up elsewhere - maths, loops, arrays and string handling, where ladder gets genuinely awkward and text stays short. For plain interlocking like this, pick whichever you and the people maintaining the machine read faster. Full guide on the blog.
๐ FULL WRITTEN GUIDE
accautomation.ca/acc-plc-simulator-how-to-use-structured-text-st-programming
๐ฅ๏ธ OPEN THE SIMULATOR AND SWITCH MODES
accautomation.ca/simulator
โถ WATCH THE FULL VIDEO
youtu.be/B0UDgJnE3DQ
๐ WHAT YOU'LL LEARN
โ Compare the same circuit honestly - two rungs of ladder against two lines of structured text, with identical behaviour and identical addresses
โ See how three parallel ladder branches become one bracketed OR expression, in series with the stop contact
โ Understand what each language is actually better at - ladder for tracing a diagram, text for maths, loops and data handling
โ Write it both ways in the same simulator, against the same X, Y and C registers, and judge for yourself which you read faster
โ Decide on the right basis - not line count, but who has to maintain the machine at three in the morning
โ FREQUENTLY ASKED
Q: Is structured text shorter than ladder logic?
A: Not for simple interlocking. This circuit is two rungs or two lines either way. Text wins clearly on maths, loops, arrays and string handling, which is where ladder needs many rungs to do something a single line expresses.
Q: So which should I use?
A: Whichever is read faster by the people who will maintain the machine. A maintenance electrician tracing a fault at three in the morning usually reads ladder quicker. A calculation or a data table is far clearer in text. Most real programs benefit from both.
Q: Does the behaviour change between the two versions?
A: No. Same addresses, same scan behaviour, same I/O. In the simulator both modes read and write the same X, Y, C, AX and AY registers, so you can write it one way, switch, and write it the other against the same memory.
๐ The full guide, with every statement and function block: accautomation.ca/acc-plc-simulator-how-to-use-structured-text-st-programming
๐ MORE RESOURCES
โถ Try the free simulator: accautomation.ca/simulator
โถ How I learned structured text in the simulator: youtu.be/B0UDgJnE3DQ
โถ PLC Beginners Guide: accautomation.ca/programming/plc-beginners-guide
โถ Free eBooks: accautomation.ca (subscribe for download)
๐ RECOMMENDED HARDWARE
โถ Shop: automationdirect.com
โถ Parts Guide: accautomation.ca/purchase-find-parts
๐ฌ Questions? Drop a comment below.
๐ New tutorials every Monday โ Subscribe and hit the bell!
#PLC #LadderLogic #IndustrialAutomation #PLCProgramming #ACCAutomation #StructuredText #IEC61131 #MotorControl #LearnPLC #Shorts
Regards,
Garry
ACC Automation
accautomation.ca
PLC start stop jog side by side: two rungs in ladder, two lines in structured text - the same circuit, and why ST's real advantage is not line count.
โก QUICK ANSWER
The same start, stop and jog circuit is two rungs in ladder and two lines in structured text:
Y1 := (X1 OR (Y1 AND NOT C1) OR X3) AND X2;
C1 := X3;
In ladder that is one rung carrying three parallel branches - start, the seal-in, and jog - in series with the normally closed stop contact, plus a second rung driving C1 from the jog input. So on size it is a draw, and anyone telling you structured text is automatically more compact has not counted. What actually differs is how you read it: ladder is a diagram you trace with your eye, structured text is one expression you read left to right. The real structured text advantage shows up elsewhere - maths, loops, arrays and string handling, where ladder gets genuinely awkward and text stays short. For plain interlocking like this, pick whichever you and the people maintaining the machine read faster. Full guide on the blog.
๐ FULL WRITTEN GUIDE
accautomation.ca/acc-plc-simulator-how-to-use-structured-text-st-programming
๐ฅ๏ธ OPEN THE SIMULATOR AND SWITCH MODES
accautomation.ca/simulator
โถ WATCH THE FULL VIDEO
youtu.be/B0UDgJnE3DQ
๐ WHAT YOU'LL LEARN
โ Compare the same circuit honestly - two rungs of ladder against two lines of structured text, with identical behaviour and identical addresses
โ See how three parallel ladder branches become one bracketed OR expression, in series with the stop contact
โ Understand what each language is actually better at - ladder for tracing a diagram, text for maths, loops and data handling
โ Write it both ways in the same simulator, against the same X, Y and C registers, and judge for yourself which you read faster
โ Decide on the right basis - not line count, but who has to maintain the machine at three in the morning
โ FREQUENTLY ASKED
Q: Is structured text shorter than ladder logic?
A: Not for simple interlocking. This circuit is two rungs or two lines either way. Text wins clearly on maths, loops, arrays and string handling, which is where ladder needs many rungs to do something a single line expresses.
Q: So which should I use?
A: Whichever is read faster by the people who will maintain the machine. A maintenance electrician tracing a fault at three in the morning usually reads ladder quicker. A calculation or a data table is far clearer in text. Most real programs benefit from both.
Q: Does the behaviour change between the two versions?
A: No. Same addresses, same scan behaviour, same I/O. In the simulator both modes read and write the same X, Y, C, AX and AY registers, so you can write it one way, switch, and write it the other against the same memory.
๐ The full guide, with every statement and function block: accautomation.ca/acc-plc-simulator-how-to-use-structured-text-st-programming
๐ MORE RESOURCES
โถ Try the free simulator: accautomation.ca/simulator
โถ How I learned structured text in the simulator: youtu.be/B0UDgJnE3DQ
โถ PLC Beginners Guide: accautomation.ca/programming/plc-beginners-guide
โถ Free eBooks: accautomation.ca (subscribe for download)
๐ RECOMMENDED HARDWARE
โถ Shop: automationdirect.com
โถ Parts Guide: accautomation.ca/purchase-find-parts
๐ฌ Questions? Drop a comment below.
๐ New tutorials every Monday โ Subscribe and hit the bell!
#PLC #LadderLogic #IndustrialAutomation #PLCProgramming #ACCAutomation #StructuredText #IEC61131 #MotorControl #LearnPLC #Shorts
Regards,
Garry
ACC Automation
accautomation.ca


![17 to 42 Instructions in One Week: The Free PLC Sim Just Leveled Up
The free ACC PLC Simulator now has 42 ladder instructions, online editing, a drum sequencer, pointers and shift registers. Runs in your browser, no install.
โก QUICK ANSWER
PLC simulator online editing means changing a rung while the program keeps scanning, exactly as you would on a plant floor where stopping the line is not an option. Press run, click edit, and an amber bar appears while the scan continues. New rungs show green, changed rungs amber, deleted rungs stay as gray ghosts. Press accept and the edit is validated first, then swapped in between two scans with timers, counters and data carried over, and cancel puts everything back. Alongside it this release adds a drum sequencer with a per step time and event bit, 4000 data registers from D1 to D4000, indirect addressing with D[D2] pointers that show the resolved address live, shift registers, jumps, master control zones, edge contacts, retentive timers and system bits.
๐ FULL WALKTHROUGH + EXAMPLES
https://accautomation.ca/free-plc-simulator-update-online-editing-drum-sequencer/
โถ RUN IT NOW, FREE IN YOUR BROWSER
https://accautomation.ca/simulator/
โฑ๏ธ TIMESTAMPS
0:00 - Introduction
0:17 - Why the ACC PLC Simulator Is Free and Browser Based
0:33 - Online Editing While the Program Keeps Scanning
1:06 - Drum Sequencer Driving a Traffic Intersection
1:22 - Inside the Drum Step Table
1:35 - 4000 Data Registers and Math Instructions
1:54 - Indirect Addressing with D[D2] Pointers
2:24 - Shift Registers, Jumps and Master Control Zones
2:44 - Edge Contacts, Retentive Timers and System Bits
3:05 - Hover Help, F1 and Structured Text Snippets
3:27 - Try It: Load the Traffic Drum Example
๐ WHAT YOULL LEARN
โ
Edit a rung online while the program keeps scanning, then accept it between two scans
โ
Read the colour code: green for new rungs, amber for changed, gray ghosts for deleted
โ
Drive a whole traffic intersection from one drum sequencer and its step table
โ
Point one instruction at any register with D[D2] and watch the address resolve live
โ
Track parts down a conveyor with bit shift registers, and skip rungs with jump and label
โ
Use first scan bits, clock pulses, scan time and the real-time clock from system words
โ FREQUENTLY ASKED
Q: What happens to my timers and counters when I accept an online edit?
A: They are carried over. The edit is validated first, then swapped in between two scans, so running values and data survive the change.
Q: What does D[D2] actually mean?
A: It is indirect addressing. The instruction uses the register whose number is stored in D2, so changing D2 points the same instruction at a different register. The block shows the resolved address live.
Q: Do I need to install anything or create an account?
A: No. It runs in a browser, it is free, there is nothing to install and no account is needed.
Q: Can I see what a jump is skipping?
A: Yes. Skipped rungs are drawn dimmed, so you can see at a glance which blocks are not being solved, and master control zones show which outputs drop when the zone turns off.
๐ Full walkthrough and examples: https://accautomation.ca/free-plc-simulator-update-online-editing-drum-sequencer/
๐ MORE RESOURCES
โถ Free PLC Simulator: https://accautomation.ca/simulator/
โถ Series: https://accautomation.ca/series/
โถ PLC Beginners Guide: https://accautomation.ca/programming/plc-beginners-guide/
โถ Free eBooks: https://accautomation.ca (subscribe for download)
๐ RECOMMENDED HARDWARE
โถ Shop: https://www.automationdirect.com/
โถ Parts Guide: https://www.accautomation.ca/purchase-find-parts/
๐ฌ Which instruction should get its own tutorial first? Drop a comment below.
๐ New tutorials every Monday โ Subscribe and hit the bell!
#PLC #LadderLogic #IndustrialAutomation #PLCProgramming #ACCAutomation #PLCSimulator #LearnPLC #PLCTutorial #FreeTraining
Regards,
Garry
ACC Automation
http://www.accautomation.ca 17 to 42 Instructions in One Week: The Free PLC Sim Just Leveled Up](https://i.ytimg.com/vi/_PJaUYQenfE/mqdefault.jpg)


![PLC Conveyor Logic Flowchart โ Simple Sequence [Tutorial]! โ๏ธ
Learn to flowchart your conveyors sequence of operations before you write a single rung โ the essential planning step in the free ACC PLC Simulator.
โก QUICK ANSWER
Before writing ladder logic for the ACC Simulator conveyor, map the sequence of operations as a flowchart: operator presses Start โ motor runs Forward โ box travels left-to-right โ hits the right sensor โ direction Reverses โ box travels right-to-left โ hits the left sensor โ motor Stops, ready for the next cycle. A Stop button can interrupt and halt the motor at any point. Turning that sequence into rungs โ contacts, seal-ins, and the simulator scene to try it โ is covered step by step in the written guide.
๐ฎ TRY IT FREE + FULL STEP-BY-STEP (build it live in the ACC PLC Simulator)
https://accautomation.ca/plc-programming-tutorial-build-a-conveyor-system-acc-simulator/
โถ WATCH THE FULL CONVEYOR BUILD
https://youtu.be/himbbHHZ6HM
๐ WHAT YOULL LEARN
โ
Map a conveyors full sequence of operations before writing any ladder logic
โ
Define the Start โ Forward โ right sensor โ Reverse โ left sensor โ Stop cycle
โ
Plan a Stop button that can interrupt and halt the motor at any point
โ
Use a flowchart to catch logic gaps before they become bugs
โ
Set up the sequence ready to build in the free ACC PLC Simulator
โ FREQUENTLY ASKED
Q: Why flowchart before programming a PLC?
A: A flowchart maps the full sequence of operations so you catch missing steps and edge cases before writing ladder logic โ it makes the actual programming faster and cleaner.
Q: What happens if someone presses Stop mid-cycle?
A: The Stop button interrupts and immediately stops the motor at any point in the sequence. How thats wired into the rungs is in the full guide.
๐ Full rung-by-rung build + the simulator scene: https://accautomation.ca/plc-programming-tutorial-build-a-conveyor-system-acc-simulator/
๐ MORE RESOURCES
โถ More tutorials + free PLC Simulator: https://accautomation.ca
โถ PLC Beginners Guide: https://accautomation.ca/programming/plc-beginners-guide/
โถ Free eBooks: https://accautomation.ca (subscribe for download)
๐ RECOMMENDED HARDWARE (optional โ this builds in the free simulator)
โถ Shop: https://www.automationdirect.com/
โถ Parts Guide: https://www.accautomation.ca/purchase-find-parts/
๐ฌ Questions? Drop a comment below.
๐ New tutorials every Monday โ Subscribe and hit the bell!
#PLC #LadderLogic #IndustrialAutomation #PLCProgramming #ACCAutomation #PLCSimulator #ConveyorControl #MotorControl #PLCTutorial #LearnPLC
Regards,
Garry
ACC Automation
http://www.accautomation.ca PLC Conveyor Logic Flowchart โ Simple Sequence [Tutorial]! โ๏ธ](https://i.ytimg.com/vi/_qJfoLcKS48/mqdefault.jpg)




