Uploaded June 2026 | Updated November 2026, 2 days ago
Learn how to use the STMR on-delay timer on the P1-M622-16DR Mini PLC to delay a motor's indicator light in a Start/Stop circuit, step by step.
โก QUICK ANSWER
On the P1-M622-16DR Mini PLC, the STMR (Simple Timer) gives you an on-delay: drop it on a rung below your Start/Stop motor circuit, drive it with your run condition (here a switch on DI 0.1.1.3), then on the next rung use a normally-open contact off the timer's "Done" tag to energize a second output โ an indicator light on DO 1.1.2. The light turns on only after the preset delay once the motor is running. The full build โ tag setup, preset value, and the downloadable project file โ is in the written guide.
๐ FULL STEP-BY-STEP + DOWNLOADS (project file, wiring diagrams, screenshots)
accautomation.ca/p1-m622-16dr-mini-plc-timer-instructions-โฑ๏ธ
โถ WATCH THE FULL VIDEO โ P1-M622-16DR Mini PLC Timer Instructions
youtu.be/Hl9-X4cxuxQ
๐ WHAT YOU'LL LEARN
โ Add the STMR (Simple Timer) on-delay instruction to a Start/Stop motor circuit
โ Use a switch input (DI 0.1.1.3) as the timer's run condition
โ Reference the timer's "Done" tag with a normally-open contact
โ Drive a second relay output (DO 1.1.2) as a delayed indicator light
โ Build a clean on-delay rung on the P1-M622-16DR Mini PLC
โ FREQUENTLY ASKED
Q: What does the STMR instruction do on a Productivity PLC?
A: STMR is the Simple Timer โ an on-delay timer. It starts timing when its run condition is true and sets its Done bit after the preset, which you then use to switch an output.
Q: How do I use the timer's Done bit?
A: Place a normally-open contact that references the timer's Done tag on a new rung, then wire it to the output you want delayed โ here an indicator light on DO 1.1.2.
๐ Full step-by-step, code & wiring diagrams: accautomation.ca/p1-m622-16dr-mini-plc-timer-instructions-โฑ๏ธ
๐ MORE RESOURCES
โถ Series: accautomation.ca/series/productivity-1000-plc
โถ PLC Beginners Guide: accautomation.ca/programming/plc-beginners-guide
โถ Free eBooks: accautomation.ca (subscribe for download)
๐ RECOMMENDED HARDWARE
โถ Shop: automationdirect.com
โถ Parts Guide: accautomation.ca/purchase-find-parts
๐ฌ Questions? Drop a comment below.
๐ New tutorials every Monday โ Subscribe and hit the bell!
#PLC #LadderLogic #IndustrialAutomation #PLCProgramming #ACCAutomation #ProductivityPLC #AutomationDirect #PLCTimer #MotorControl #PLCTutorial
Regards,
Garry
ACC Automation
accautomation.ca
Learn how to use the STMR on-delay timer on the P1-M622-16DR Mini PLC to delay a motor's indicator light in a Start/Stop circuit, step by step.
โก QUICK ANSWER
On the P1-M622-16DR Mini PLC, the STMR (Simple Timer) gives you an on-delay: drop it on a rung below your Start/Stop motor circuit, drive it with your run condition (here a switch on DI 0.1.1.3), then on the next rung use a normally-open contact off the timer's "Done" tag to energize a second output โ an indicator light on DO 1.1.2. The light turns on only after the preset delay once the motor is running. The full build โ tag setup, preset value, and the downloadable project file โ is in the written guide.
๐ FULL STEP-BY-STEP + DOWNLOADS (project file, wiring diagrams, screenshots)
accautomation.ca/p1-m622-16dr-mini-plc-timer-instructions-โฑ๏ธ
โถ WATCH THE FULL VIDEO โ P1-M622-16DR Mini PLC Timer Instructions
youtu.be/Hl9-X4cxuxQ
๐ WHAT YOU'LL LEARN
โ Add the STMR (Simple Timer) on-delay instruction to a Start/Stop motor circuit
โ Use a switch input (DI 0.1.1.3) as the timer's run condition
โ Reference the timer's "Done" tag with a normally-open contact
โ Drive a second relay output (DO 1.1.2) as a delayed indicator light
โ Build a clean on-delay rung on the P1-M622-16DR Mini PLC
โ FREQUENTLY ASKED
Q: What does the STMR instruction do on a Productivity PLC?
A: STMR is the Simple Timer โ an on-delay timer. It starts timing when its run condition is true and sets its Done bit after the preset, which you then use to switch an output.
Q: How do I use the timer's Done bit?
A: Place a normally-open contact that references the timer's Done tag on a new rung, then wire it to the output you want delayed โ here an indicator light on DO 1.1.2.
๐ Full step-by-step, code & wiring diagrams: accautomation.ca/p1-m622-16dr-mini-plc-timer-instructions-โฑ๏ธ
๐ MORE RESOURCES
โถ Series: accautomation.ca/series/productivity-1000-plc
โถ PLC Beginners Guide: accautomation.ca/programming/plc-beginners-guide
โถ Free eBooks: accautomation.ca (subscribe for download)
๐ RECOMMENDED HARDWARE
โถ Shop: automationdirect.com
โถ Parts Guide: accautomation.ca/purchase-find-parts
๐ฌ Questions? Drop a comment below.
๐ New tutorials every Monday โ Subscribe and hit the bell!
#PLC #LadderLogic #IndustrialAutomation #PLCProgramming #ACCAutomation #ProductivityPLC #AutomationDirect #PLCTimer #MotorControl #PLCTutorial
Regards,
Garry
ACC Automation
accautomation.ca

![17 to 42 Instructions in One Week: The Free PLC Sim Just Leveled Up
The free ACC PLC Simulator now has 42 ladder instructions, online editing, a drum sequencer, pointers and shift registers. Runs in your browser, no install.
โก QUICK ANSWER
PLC simulator online editing means changing a rung while the program keeps scanning, exactly as you would on a plant floor where stopping the line is not an option. Press run, click edit, and an amber bar appears while the scan continues. New rungs show green, changed rungs amber, deleted rungs stay as gray ghosts. Press accept and the edit is validated first, then swapped in between two scans with timers, counters and data carried over, and cancel puts everything back. Alongside it this release adds a drum sequencer with a per step time and event bit, 4000 data registers from D1 to D4000, indirect addressing with D[D2] pointers that show the resolved address live, shift registers, jumps, master control zones, edge contacts, retentive timers and system bits.
๐ FULL WALKTHROUGH + EXAMPLES
https://accautomation.ca/free-plc-simulator-update-online-editing-drum-sequencer/
โถ RUN IT NOW, FREE IN YOUR BROWSER
https://accautomation.ca/simulator/
โฑ๏ธ TIMESTAMPS
0:00 - Introduction
0:17 - Why the ACC PLC Simulator Is Free and Browser Based
0:33 - Online Editing While the Program Keeps Scanning
1:06 - Drum Sequencer Driving a Traffic Intersection
1:22 - Inside the Drum Step Table
1:35 - 4000 Data Registers and Math Instructions
1:54 - Indirect Addressing with D[D2] Pointers
2:24 - Shift Registers, Jumps and Master Control Zones
2:44 - Edge Contacts, Retentive Timers and System Bits
3:05 - Hover Help, F1 and Structured Text Snippets
3:27 - Try It: Load the Traffic Drum Example
๐ WHAT YOULL LEARN
โ
Edit a rung online while the program keeps scanning, then accept it between two scans
โ
Read the colour code: green for new rungs, amber for changed, gray ghosts for deleted
โ
Drive a whole traffic intersection from one drum sequencer and its step table
โ
Point one instruction at any register with D[D2] and watch the address resolve live
โ
Track parts down a conveyor with bit shift registers, and skip rungs with jump and label
โ
Use first scan bits, clock pulses, scan time and the real-time clock from system words
โ FREQUENTLY ASKED
Q: What happens to my timers and counters when I accept an online edit?
A: They are carried over. The edit is validated first, then swapped in between two scans, so running values and data survive the change.
Q: What does D[D2] actually mean?
A: It is indirect addressing. The instruction uses the register whose number is stored in D2, so changing D2 points the same instruction at a different register. The block shows the resolved address live.
Q: Do I need to install anything or create an account?
A: No. It runs in a browser, it is free, there is nothing to install and no account is needed.
Q: Can I see what a jump is skipping?
A: Yes. Skipped rungs are drawn dimmed, so you can see at a glance which blocks are not being solved, and master control zones show which outputs drop when the zone turns off.
๐ Full walkthrough and examples: https://accautomation.ca/free-plc-simulator-update-online-editing-drum-sequencer/
๐ MORE RESOURCES
โถ Free PLC Simulator: https://accautomation.ca/simulator/
โถ Series: https://accautomation.ca/series/
โถ PLC Beginners Guide: https://accautomation.ca/programming/plc-beginners-guide/
โถ Free eBooks: https://accautomation.ca (subscribe for download)
๐ RECOMMENDED HARDWARE
โถ Shop: https://www.automationdirect.com/
โถ Parts Guide: https://www.accautomation.ca/purchase-find-parts/
๐ฌ Which instruction should get its own tutorial first? Drop a comment below.
๐ New tutorials every Monday โ Subscribe and hit the bell!
#PLC #LadderLogic #IndustrialAutomation #PLCProgramming #ACCAutomation #PLCSimulator #LearnPLC #PLCTutorial #FreeTraining
Regards,
Garry
ACC Automation
http://www.accautomation.ca 17 to 42 Instructions in One Week: The Free PLC Sim Just Leveled Up](https://i.ytimg.com/vi/_PJaUYQenfE/mqdefault.jpg)


![PLC Conveyor Logic Flowchart โ Simple Sequence [Tutorial]! โ๏ธ
Learn to flowchart your conveyors sequence of operations before you write a single rung โ the essential planning step in the free ACC PLC Simulator.
โก QUICK ANSWER
Before writing ladder logic for the ACC Simulator conveyor, map the sequence of operations as a flowchart: operator presses Start โ motor runs Forward โ box travels left-to-right โ hits the right sensor โ direction Reverses โ box travels right-to-left โ hits the left sensor โ motor Stops, ready for the next cycle. A Stop button can interrupt and halt the motor at any point. Turning that sequence into rungs โ contacts, seal-ins, and the simulator scene to try it โ is covered step by step in the written guide.
๐ฎ TRY IT FREE + FULL STEP-BY-STEP (build it live in the ACC PLC Simulator)
https://accautomation.ca/plc-programming-tutorial-build-a-conveyor-system-acc-simulator/
โถ WATCH THE FULL CONVEYOR BUILD
https://youtu.be/himbbHHZ6HM
๐ WHAT YOULL LEARN
โ
Map a conveyors full sequence of operations before writing any ladder logic
โ
Define the Start โ Forward โ right sensor โ Reverse โ left sensor โ Stop cycle
โ
Plan a Stop button that can interrupt and halt the motor at any point
โ
Use a flowchart to catch logic gaps before they become bugs
โ
Set up the sequence ready to build in the free ACC PLC Simulator
โ FREQUENTLY ASKED
Q: Why flowchart before programming a PLC?
A: A flowchart maps the full sequence of operations so you catch missing steps and edge cases before writing ladder logic โ it makes the actual programming faster and cleaner.
Q: What happens if someone presses Stop mid-cycle?
A: The Stop button interrupts and immediately stops the motor at any point in the sequence. How thats wired into the rungs is in the full guide.
๐ Full rung-by-rung build + the simulator scene: https://accautomation.ca/plc-programming-tutorial-build-a-conveyor-system-acc-simulator/
๐ MORE RESOURCES
โถ More tutorials + free PLC Simulator: https://accautomation.ca
โถ PLC Beginners Guide: https://accautomation.ca/programming/plc-beginners-guide/
โถ Free eBooks: https://accautomation.ca (subscribe for download)
๐ RECOMMENDED HARDWARE (optional โ this builds in the free simulator)
โถ Shop: https://www.automationdirect.com/
โถ Parts Guide: https://www.accautomation.ca/purchase-find-parts/
๐ฌ Questions? Drop a comment below.
๐ New tutorials every Monday โ Subscribe and hit the bell!
#PLC #LadderLogic #IndustrialAutomation #PLCProgramming #ACCAutomation #PLCSimulator #ConveyorControl #MotorControl #PLCTutorial #LearnPLC
Regards,
Garry
ACC Automation
http://www.accautomation.ca PLC Conveyor Logic Flowchart โ Simple Sequence [Tutorial]! โ๏ธ](https://i.ytimg.com/vi/_qJfoLcKS48/mqdefault.jpg)





