Uploaded May 2026 | Updated November 2026, 2 hours ago
PLC seal-in vs jog motor control: with a seal-in (latch), press and release the start button and the motor stays running; with a jog, the motor runs only while you hold the button. Watch both live in the free ACC PLC Simulator Control Panel scene.
⚡ QUICK ANSWER
This shows the difference between a seal-in and a jog for motor control, live in the ACC PLC Simulator Control Panel scene. With a seal-in, also called a latch, you press the green start button and release it, and the motor stays running, because the seal-in contact holds the circuit on. It keeps running until you press stop, which drops it out and the motor stops. With a jog, there is no seal-in: you hold the button and the motor runs, and the moment you release it the motor stops immediately. So a seal-in is the standard start and stop pattern, where a momentary press latches the motor on, while a jog is momentary control for inching or positioning, where the motor only runs while you hold the button. Seeing both behaviours side by side in the 3D scene makes the difference clear. You can try it yourself for free in the browser-based simulator. The link is below.
⚙️ SEAL-IN (LATCH)
▶ Press the green start button and release it — the motor STAYS running
▶ The seal-in contact holds the circuit on
▶ Press stop and the motor stops
▶ This is the standard start/stop pattern — a momentary press latches the motor on
⚙️ JOG (MOMENTARY)
▶ Hold the button and the motor runs
▶ Release it and the motor stops immediately
▶ No seal-in — the motor runs only while you hold the button
▶ Used for inching or positioning
🕹️ TRY IT FREE — THE ACC PLC SIMULATOR CONTROL PANEL SCENE
accautomation.ca/simulator
📚 WHAT YOU'LL LEARN
✅ The difference between a seal-in (latch) and a jog
✅ Why a seal-in keeps the motor running after you release the button
✅ Why a jog runs the motor only while you hold the button
✅ Why a seal-in is the standard start/stop pattern
✅ When you'd use a jog (inching or positioning)
❓ FREQUENTLY ASKED
Q: What's the difference between a seal-in and a jog?
A: With a seal-in (latch), a momentary press keeps the motor running until you press stop. With a jog, the motor runs only while you hold the button and stops the instant you release it. Try both free at the link.
Q: Why does the motor keep running after I release the start button?
A: Because of the seal-in contact — it holds the circuit on after the momentary press. Press stop to drop it out. A jog has no seal-in, so it stops on release.
👉 Try it free: accautomation.ca/simulator
🔗 MORE RESOURCES
🎮 Free ACC PLC Simulator (3D scenes, no install): accautomation.ca/simulator
▶ The Motor Starter Scene (start/stop/overload): youtube.com/shorts/5qVbD0NfhIE
▶ Run a Start-Stop-Jog Program With a Gamepad: youtube.com/shorts/nilrOfKYE3k
▶ PLC Beginners Guide: accautomation.ca/programming/plc-beginners-guide
▶ Free eBooks: accautomation.ca (subscribe for download)
💬 Questions? Drop a comment below.
🔔 New tutorials every Monday — Subscribe and hit the bell!
#PLC #LadderLogic #IndustrialAutomation #PLCProgramming #ACCAutomation #PLCSimulator #SealIn #Jog #MotorControl #Shorts
Regards,
Garry
ACC Automation
accautomation.ca
PLC seal-in vs jog motor control: with a seal-in (latch), press and release the start button and the motor stays running; with a jog, the motor runs only while you hold the button. Watch both live in the free ACC PLC Simulator Control Panel scene.
⚡ QUICK ANSWER
This shows the difference between a seal-in and a jog for motor control, live in the ACC PLC Simulator Control Panel scene. With a seal-in, also called a latch, you press the green start button and release it, and the motor stays running, because the seal-in contact holds the circuit on. It keeps running until you press stop, which drops it out and the motor stops. With a jog, there is no seal-in: you hold the button and the motor runs, and the moment you release it the motor stops immediately. So a seal-in is the standard start and stop pattern, where a momentary press latches the motor on, while a jog is momentary control for inching or positioning, where the motor only runs while you hold the button. Seeing both behaviours side by side in the 3D scene makes the difference clear. You can try it yourself for free in the browser-based simulator. The link is below.
⚙️ SEAL-IN (LATCH)
▶ Press the green start button and release it — the motor STAYS running
▶ The seal-in contact holds the circuit on
▶ Press stop and the motor stops
▶ This is the standard start/stop pattern — a momentary press latches the motor on
⚙️ JOG (MOMENTARY)
▶ Hold the button and the motor runs
▶ Release it and the motor stops immediately
▶ No seal-in — the motor runs only while you hold the button
▶ Used for inching or positioning
🕹️ TRY IT FREE — THE ACC PLC SIMULATOR CONTROL PANEL SCENE
accautomation.ca/simulator
📚 WHAT YOU'LL LEARN
✅ The difference between a seal-in (latch) and a jog
✅ Why a seal-in keeps the motor running after you release the button
✅ Why a jog runs the motor only while you hold the button
✅ Why a seal-in is the standard start/stop pattern
✅ When you'd use a jog (inching or positioning)
❓ FREQUENTLY ASKED
Q: What's the difference between a seal-in and a jog?
A: With a seal-in (latch), a momentary press keeps the motor running until you press stop. With a jog, the motor runs only while you hold the button and stops the instant you release it. Try both free at the link.
Q: Why does the motor keep running after I release the start button?
A: Because of the seal-in contact — it holds the circuit on after the momentary press. Press stop to drop it out. A jog has no seal-in, so it stops on release.
👉 Try it free: accautomation.ca/simulator
🔗 MORE RESOURCES
🎮 Free ACC PLC Simulator (3D scenes, no install): accautomation.ca/simulator
▶ The Motor Starter Scene (start/stop/overload): youtube.com/shorts/5qVbD0NfhIE
▶ Run a Start-Stop-Jog Program With a Gamepad: youtube.com/shorts/nilrOfKYE3k
▶ PLC Beginners Guide: accautomation.ca/programming/plc-beginners-guide
▶ Free eBooks: accautomation.ca (subscribe for download)
💬 Questions? Drop a comment below.
🔔 New tutorials every Monday — Subscribe and hit the bell!
#PLC #LadderLogic #IndustrialAutomation #PLCProgramming #ACCAutomation #PLCSimulator #SealIn #Jog #MotorControl #Shorts
Regards,
Garry
ACC Automation
accautomation.ca










