Uploaded December 2019 | Updated November 2026, 3 days ago
Linear Power Supply Circuit [LM317, LM337, Adjustable & Low Noise]
A single-output transformer
=============================================
Article Source: pcbway.com/blog/technology/Low_Noise_Adjustable_Linear_AC_DC_Power_Supply.html
=============================================
Support me on Patreon: patreon.com/myvanitar
=============================================
Check other videos: bit.ly/2N9OlPa
============================================
Features:
AC – DC Conversion
Double output voltages (Positive – Ground – Negative)
Adjustable positive and negative rails
Just a Single-Output AC transformer
Output noise (20MHz-BWL, no load): Around 1.12mVpp
Low noise and stable outputs (ideal to power Opamps)
Output Voltage: +/-1.25V to +/-25V
Maximum output current: 300mA to 500mA
Cheap and easy to solder (all component packages are DIP)
A double output low noise power supply is an essential tool for any electronics enthusiast. There are many circumstances that a double-output power supply is necessary such as designing pre-amplifiers and powering OPAMPs. In this article, we are going to build a linear power supply that a user can adjust its positive and negative rails independently. Moreover, just an ordinary single-output AC transformer is used at the input.D1 and D2 are rectifier diodes.
C1 and C2 build the first noise reduction filter stage. R1, R2, C1, C2, C3, C4, C5, and C6 build a low pass RC filter which reduces noise from both positive and negative rails. The behavior of this filter can be examined both in theory and practice. An oscilloscope with a bode plot feature can perform these measurements, such as a Siglent SDS1104X-E.IC1 [1] and IC2 [2] are the main regulation components of this circuit. According to the IC1 (LM317) datasheet: “The LM317 device is an adjustable three-terminal positive-voltage regulator capable of supplying more than 1.5 A over an output-voltage range of 1.25 V to 37 V. It requires only two external resistors to set the output voltage. The device features a typical line regulation of 0.01% and a typical load regulation of 0.1%. It includes current limiting, thermal overload protection, and safe operating area protection. Overload protection remains functional even if the ADJUST terminal is disconnected”.As it is clear, this regulator introduces good line and load regulation figures, therefore we can expect to get a stable output rail. This is identical to the IC2 (LM337). The only difference is that this chip is used to regulate the negative voltages.D3 and D4 are used for protection. The diodes provide a low-impedance discharge path to prevent the capacitors (C9 and C10) from discharging into the output of the regulators.R4 and R5 are used to adjust the output voltages. C7, C8, C9, and C10 are used to filter the remained output noises.
#adjustable_power_supply
#LM317
#LM337
Linear Power Supply Circuit [LM317, LM337, Adjustable & Low Noise]
A single-output transformer
=============================================
Article Source: pcbway.com/blog/technology/Low_Noise_Adjustable_Linear_AC_DC_Power_Supply.html
=============================================
Support me on Patreon: patreon.com/myvanitar
=============================================
Check other videos: bit.ly/2N9OlPa
============================================
Features:
AC – DC Conversion
Double output voltages (Positive – Ground – Negative)
Adjustable positive and negative rails
Just a Single-Output AC transformer
Output noise (20MHz-BWL, no load): Around 1.12mVpp
Low noise and stable outputs (ideal to power Opamps)
Output Voltage: +/-1.25V to +/-25V
Maximum output current: 300mA to 500mA
Cheap and easy to solder (all component packages are DIP)
A double output low noise power supply is an essential tool for any electronics enthusiast. There are many circumstances that a double-output power supply is necessary such as designing pre-amplifiers and powering OPAMPs. In this article, we are going to build a linear power supply that a user can adjust its positive and negative rails independently. Moreover, just an ordinary single-output AC transformer is used at the input.D1 and D2 are rectifier diodes.
C1 and C2 build the first noise reduction filter stage. R1, R2, C1, C2, C3, C4, C5, and C6 build a low pass RC filter which reduces noise from both positive and negative rails. The behavior of this filter can be examined both in theory and practice. An oscilloscope with a bode plot feature can perform these measurements, such as a Siglent SDS1104X-E.IC1 [1] and IC2 [2] are the main regulation components of this circuit. According to the IC1 (LM317) datasheet: “The LM317 device is an adjustable three-terminal positive-voltage regulator capable of supplying more than 1.5 A over an output-voltage range of 1.25 V to 37 V. It requires only two external resistors to set the output voltage. The device features a typical line regulation of 0.01% and a typical load regulation of 0.1%. It includes current limiting, thermal overload protection, and safe operating area protection. Overload protection remains functional even if the ADJUST terminal is disconnected”.As it is clear, this regulator introduces good line and load regulation figures, therefore we can expect to get a stable output rail. This is identical to the IC2 (LM337). The only difference is that this chip is used to regulate the negative voltages.D3 and D4 are used for protection. The diodes provide a low-impedance discharge path to prevent the capacitors (C9 and C10) from discharging into the output of the regulators.R4 and R5 are used to adjust the output voltages. C7, C8, C9, and C10 are used to filter the remained output noises.
#adjustable_power_supply
#LM317
#LM337






![[PCB Update] AC to DC Transformerless Power Supply
AC to DC Transformerless Power Supply, PCB Update
Ive modified the wrong clearance for two capacitor pins
Altium-365 Workspace (Free): https://www.altium365.com/yt/myvanitar
PCB Fabrication (1$ for 10Pcs): https://www.pcbx.com/?mtm_campaign=AD&mtm_kwd=MyV&mtm_source=YT
Schematic/PCB/Gerber: https://365.altium.com/files/75F890FD-DD2D-415E-A9E6-1F7CB2435219
Other Videos: http://bit.ly/2N9OlPa
Whenever you hear the transformerless (AC to DC converter without transformer) supply term, you initially imagine the capacitor-based solution: a high-voltage non-polarized capacitor in series with the mains line, a bridge rectifier, a Zener diode, and a filtering electrolytic capacitor. Such a circuit is not only unable to deliver sufficient current for many applications, it is also not a reliable solution for the industry. However, you might see such circuits in some cheap products.
The AL17150-10B is a universal high-voltage input step-down regulator product family, which provides accurate Constant Voltage (CV) and outstanding dynamic performance without requiring an optocoupler over line and load regulation. Typical applications are offline low power applications including connected LED lighting power supply for microcontrollers and other IoT applications. The AL17150-10B integrates a 500V/1A MOSFET that can make it use fewer external components and create a low Bill Of Material (BOM) cost solution. The AL17150-10B can provide up to 300mA output current and lower than 50mW standby power, which is very suitable for IoT-connected lighting devices. The AL17150-10B achieves excellent regulation and high power efficiency. The characteristics of max peak current and driving frequency vary as the load changes, which can get excellent efficiency performance at light load and improve the overall average efficiency. The AL17150-10B has rich protection features to enhance the system safety and reliability. It has Over Temperature Protection, VCC Under Voltage Lock function, Output Short Protection, Over-Load Protection, and Open Loop Protection (220v AC to 12v DC converter without transformer).
The AL17150-10B is available in the SO-7 package. [PCB Update] AC to DC Transformerless Power Supply](https://i.ytimg.com/vi/StoZTyxJi3g/mqdefault.jpg)


![Active Low Pass Filter Bode Plot Analysis using Siglent SDS2102X Plus Oscilloscope [Part-2]
Active Low Pass Filter Bode Plot Analysis using Siglent SDS2102X Plus Oscilloscope
In the second part of the active low pass filter analysis videos, I used the bode plot to analyze the low pass active filters behavior in practice. There are not many devices that can calculate and demonstrate the bode plot. I used Siglent SDS2102X Plus oscilloscope to plot the bode curve. The cut-off frequency of the filter, in theory, is around 722Hz, however, in practice, the result would be different. The cut-off frequency of a filter is where the X-Axis (frequency) meets the Y-Axis (amplitude) at the -3dB point. The Siglent SDS2000x plus series oscilloscopes offer tons of features for bode plot analysis in practice.
Check other videos: http://bit.ly/2N9OlPa
Tools
Siglent SDS2102X Plus: https://www.siglenteu.com/digital-oscilloscopes/sds2000xp
Inspired by:
ALL ABOUT ELECTRONICS
Active Low Pass Filter and Active High Pass Filter Explained
URL: https://www.youtube.com/watch?v=gEeF8sEQTEc
Inspired by:
The Organic Chemistry Tutor
Low Pass Filters and High Pass Filters - RC and RL Circuits
URL: https://www.youtube.com/watch?v=lagfhNjMuQM
Inspired by:
RC Low Pass Filter, Single Pole, Magnitude, Phase and 3dB Frequency
eeKnowHow
URL: https://www.youtube.com/watch?v=jNZa_G5R85U
Inspired By:
EEVblog 396 - Bode Plotting on Your Osciloscope
EEVBlog
URL: https://www.youtube.com/watch?v=uMH2hGvqhlE
#bode_plot
#frequency_response
#filter Active Low Pass Filter Bode Plot Analysis using Siglent SDS2102X Plus Oscilloscope [Part-2]](https://i.ytimg.com/vi/UY8NIkUCe0E/mqdefault.jpg)
