Uploaded September 2025 | Updated November 2026, 5 days ago
How to Replace the Joystick and Calibrate the Joystick of T8S Transmitter?
Prepare a screwdriver, With a S2 PH1 bit.
We need to loose the six screws at the back of the transmitter.
Open it. We need to unplug the cables
Here are the two joysticks.
The left stick which does not return to the center is the throttle stick.
The right stick will return to the center automatically. You can replace any one of them.
(RadioLink AliExpress official store:radiolink.aliexpress.com/store/1101309511
Please contact AliExpress sales for the purchase link of the joystick)
To replace the two joysticks, we need to loose these screws so we can remove the broken joystick.
After you replace the joystick, you also need to tighten these screws.
Take the throttle stick as an example.
Remove the screws.
Here is a cable inside.
We can remove the joystick now.
Here is the connection cable of the joystick.
Unplug the cable.
When you plug the cable, please make sure the connection is correct.
Imagine the new joystick is installed.
Tighten the screws.
The new joystick is installed.
We can see the joystick work well.
Connect all the cables. Make sure the cable is not near the screws.
After replacing the joystick, we need to calibrate the joystick.
Press the trim button on the left, and power on T8S at the same time.
LED indicators start flashing means it enters the joystick calibration mode.
Push the two joysticks to the four corners to make sure the joysticks reach the maximum and minimum travel.
Then put the two joysticks to the center point.
And press the second trim button on the left. LED indicators turn solid green means joystick calibration is complete.
So that’s all about how to replace the joystick of T8S transmitter.
More details about T8S:
radiolink.com/t8s
You can buy T8S from the link:
radiolink.com/t8s_where_to_buy
You can send mails to after_service@radiolink.com.cn if you have any questions during using our products.
#rcplane #transmitter #radiolink
How to Replace the Joystick and Calibrate the Joystick of T8S Transmitter?
Prepare a screwdriver, With a S2 PH1 bit.
We need to loose the six screws at the back of the transmitter.
Open it. We need to unplug the cables
Here are the two joysticks.
The left stick which does not return to the center is the throttle stick.
The right stick will return to the center automatically. You can replace any one of them.
(RadioLink AliExpress official store:radiolink.aliexpress.com/store/1101309511
Please contact AliExpress sales for the purchase link of the joystick)
To replace the two joysticks, we need to loose these screws so we can remove the broken joystick.
After you replace the joystick, you also need to tighten these screws.
Take the throttle stick as an example.
Remove the screws.
Here is a cable inside.
We can remove the joystick now.
Here is the connection cable of the joystick.
Unplug the cable.
When you plug the cable, please make sure the connection is correct.
Imagine the new joystick is installed.
Tighten the screws.
The new joystick is installed.
We can see the joystick work well.
Connect all the cables. Make sure the cable is not near the screws.
After replacing the joystick, we need to calibrate the joystick.
Press the trim button on the left, and power on T8S at the same time.
LED indicators start flashing means it enters the joystick calibration mode.
Push the two joysticks to the four corners to make sure the joysticks reach the maximum and minimum travel.
Then put the two joysticks to the center point.
And press the second trim button on the left. LED indicators turn solid green means joystick calibration is complete.
So that’s all about how to replace the joystick of T8S transmitter.
More details about T8S:
radiolink.com/t8s
You can buy T8S from the link:
radiolink.com/t8s_where_to_buy
You can send mails to after_service@radiolink.com.cn if you have any questions during using our products.
#rcplane #transmitter #radiolink










