Uploaded June 2025 | Updated November 2026, 4 days ago
3.8V to 55V, 2MHz, 2A DC to DC Step Down (Buck) Converter using MP4560
======================================
Altium Designer + Altium-365 (Free): altium.com/yt/MyVanitar
======================================
Article: powerelectronicsnews.com/3-8v-to-55v-2-mhz-2-a-dc-to-dc-step-down-converter-for-no-feedback-output-of-the-flyback
======================================
Schematic & PCB: 365.altium.com/files/09BC774B-E1CF-4265-A5E5-03EC3CE14EAC
======================================
Other Videos: bit.ly/2N9OlPa
======================================
@AtiumOfficial
#altiumstories
This video introduces a wide 3.8V-55V input range, high-frequency, and efficient DC-to-DC step-down converter board using the Monolithic Power Systems MP4560 chip.
The MP4560 is a high-frequency step-down switching regulator with integrated internal high-side high voltage power MOSFET. It provides 2A output with current mode control for fast loop response and easy compensation. The wide 3.8V to 55V input range accommodates a variety of step-down applications, including those in automotive input environments. A 12μA shutdown mode supply current allows use in battery-powered applications. High power conversion efficiency over a wide load range is achieved by scaling down the switching frequency at light load conditions to reduce the switching and gate-driving losses. The frequency foldback helps prevent inductor current runaway during startup and thermal shutdown provides reliable, fault-tolerant operation. By switching at 2MHz, the MP4560 can prevent EMI (Electromagnetic Interference) noise problems, such as those found in AM radio and ADSL applications. The MP4560 is available in small 3mm x 3mm 10-pin QFN and SOIC8 with exposed pad packages.
3.8V to 55V, 2MHz, 2A DC to DC Step Down (Buck) Converter using MP4560
======================================
Altium Designer + Altium-365 (Free): altium.com/yt/MyVanitar
======================================
Article: powerelectronicsnews.com/3-8v-to-55v-2-mhz-2-a-dc-to-dc-step-down-converter-for-no-feedback-output-of-the-flyback
======================================
Schematic & PCB: 365.altium.com/files/09BC774B-E1CF-4265-A5E5-03EC3CE14EAC
======================================
Other Videos: bit.ly/2N9OlPa
======================================
@AtiumOfficial
#altiumstories
This video introduces a wide 3.8V-55V input range, high-frequency, and efficient DC-to-DC step-down converter board using the Monolithic Power Systems MP4560 chip.
The MP4560 is a high-frequency step-down switching regulator with integrated internal high-side high voltage power MOSFET. It provides 2A output with current mode control for fast loop response and easy compensation. The wide 3.8V to 55V input range accommodates a variety of step-down applications, including those in automotive input environments. A 12μA shutdown mode supply current allows use in battery-powered applications. High power conversion efficiency over a wide load range is achieved by scaling down the switching frequency at light load conditions to reduce the switching and gate-driving losses. The frequency foldback helps prevent inductor current runaway during startup and thermal shutdown provides reliable, fault-tolerant operation. By switching at 2MHz, the MP4560 can prevent EMI (Electromagnetic Interference) noise problems, such as those found in AM radio and ADSL applications. The MP4560 is available in small 3mm x 3mm 10-pin QFN and SOIC8 with exposed pad packages.




![Linear Power Supply Circuit [LM317, LM337, Adjustable & Low Noise]
Linear Power Supply Circuit [LM317, LM337, Adjustable & Low Noise]
A single-output transformer
Article Source: https://www.pcbway.com/blog/technology/Low_Noise_Adjustable_Linear_AC_DC_Power_Supply.html
Support me on Patreon: https://www.patreon.com/myvanitar
Check other videos: http://bit.ly/2N9OlPa
Features:
AC – DC Conversion
Double output voltages (Positive – Ground – Negative)
Adjustable positive and negative rails
Just a Single-Output AC transformer
Output noise (20MHz-BWL, no load): Around 1.12mVpp
Low noise and stable outputs (ideal to power Opamps)
Output Voltage: +/-1.25V to +/-25V
Maximum output current: 300mA to 500mA
Cheap and easy to solder (all component packages are DIP)
A double output low noise power supply is an essential tool for any electronics enthusiast. There are many circumstances that a double-output power supply is necessary such as designing pre-amplifiers and powering OPAMPs. In this article, we are going to build a linear power supply that a user can adjust its positive and negative rails independently. Moreover, just an ordinary single-output AC transformer is used at the input.D1 and D2 are rectifier diodes.
C1 and C2 build the first noise reduction filter stage. R1, R2, C1, C2, C3, C4, C5, and C6 build a low pass RC filter which reduces noise from both positive and negative rails. The behavior of this filter can be examined both in theory and practice. An oscilloscope with a bode plot feature can perform these measurements, such as a Siglent SDS1104X-E.IC1 [1] and IC2 [2] are the main regulation components of this circuit. According to the IC1 (LM317) datasheet: “The LM317 device is an adjustable three-terminal positive-voltage regulator capable of supplying more than 1.5 A over an output-voltage range of 1.25 V to 37 V. It requires only two external resistors to set the output voltage. The device features a typical line regulation of 0.01% and a typical load regulation of 0.1%. It includes current limiting, thermal overload protection, and safe operating area protection. Overload protection remains functional even if the ADJUST terminal is disconnected”.As it is clear, this regulator introduces good line and load regulation figures, therefore we can expect to get a stable output rail. This is identical to the IC2 (LM337). The only difference is that this chip is used to regulate the negative voltages.D3 and D4 are used for protection. The diodes provide a low-impedance discharge path to prevent the capacitors (C9 and C10) from discharging into the output of the regulators.R4 and R5 are used to adjust the output voltages. C7, C8, C9, and C10 are used to filter the remained output noises.
#adjustable_power_supply
#LM317
#LM337 Linear Power Supply Circuit [LM317, LM337, Adjustable & Low Noise]](https://i.ytimg.com/vi/ObFXqTvyjyU/mqdefault.jpg)





