Uploaded September 2026 | Updated November 2026, 3 hours ago
Five Steps to PLC program development: stop endless rewrites. Writing the program is only Step 4 โ skip the front-end planning and you don't save time, you move it to the back end with interest. Plan before you program.
โก QUICK ANSWER
Endless rewrites are what happen when you skip the planning and jump straight to writing code. That's why I teach the Five Steps to PLC Program Development, and the key thing to understand is that writing the program is only Step 4. Most of the work is the front-end planning that comes before you write a single rung. If you skip that front end to save time, you don't actually save it, you just move it to the back end with interest, in the form of rewrites, debugging, and rework. Planning first is what stops the endless-rewrite cycle. It's also why I built the ACC PLC Simulator, so you can plan and prove your logic before you program it for real. Plan before you program, and the writing step goes much more smoothly. Try the simulator free at the link below.
๐ก THE KEY INSIGHT
โถ Writing the program is only Step 4 of the Five Steps
โถ Most of the work is the front-end planning that comes first
โถ Skip the front end and you don't save time โ you move it to the back end with interest
โถ That "interest" is endless rewrites, debugging, and rework
โถ Plan before you program to stop the rewrite cycle
๐ LEARN THE PROCESS โ PLC BEGINNERS GUIDE
accautomation.ca/programming/plc-beginners-guide
๐น๏ธ PLAN AND PROVE IT FIRST โ THE FREE ACC PLC SIMULATOR
accautomation.ca/simulator
๐ WHAT YOU'LL LEARN
โ Why endless rewrites come from skipping the planning
โ Why writing the program is only Step 4 of the process
โ Why the front-end planning is most of the work
โ Why skipping it moves the time to the back end with interest
โ Why planning before you program stops the rewrite cycle
โ FREQUENTLY ASKED
Q: Why is writing the program only Step 4?
A: Because most of the work in PLC development is the front-end planning that comes before you write code. Writing is just one step of the Five Steps. Skipping the planning is what causes endless rewrites.
Q: How do I stop endless rewrites?
A: Plan before you program. Do the front-end steps first, and prove your logic in a simulator before you build it for real, so you're not deferring the work to the back end with interest.
๐ Try the simulator free: accautomation.ca/simulator
๐ MORE RESOURCES
๐ฎ Free ACC PLC Simulator (plan and prove your logic, no install): accautomation.ca/simulator
โถ 10 Minutes on a Simulator Beats an Hour of Reading: youtube.com/shorts/BMoAvoA47lY
โถ PLC Programming Isn't Hard โ It's Dangerous: youtu.be/_TIHwDAIQo0
โถ PLC Beginners Guide: accautomation.ca/programming/plc-beginners-guide
โถ Free eBooks: accautomation.ca (subscribe for download)
๐ฌ Questions? Drop a comment below.
๐ New tutorials every Monday โ Subscribe and hit the bell!
#PLC #LadderLogic #IndustrialAutomation #PLCProgramming #ACCAutomation #PLCDesign #LearnPLC #PLCSimulator #FiveSteps #Shorts
Regards,
Garry
ACC Automation
accautomation.ca
Five Steps to PLC program development: stop endless rewrites. Writing the program is only Step 4 โ skip the front-end planning and you don't save time, you move it to the back end with interest. Plan before you program.
โก QUICK ANSWER
Endless rewrites are what happen when you skip the planning and jump straight to writing code. That's why I teach the Five Steps to PLC Program Development, and the key thing to understand is that writing the program is only Step 4. Most of the work is the front-end planning that comes before you write a single rung. If you skip that front end to save time, you don't actually save it, you just move it to the back end with interest, in the form of rewrites, debugging, and rework. Planning first is what stops the endless-rewrite cycle. It's also why I built the ACC PLC Simulator, so you can plan and prove your logic before you program it for real. Plan before you program, and the writing step goes much more smoothly. Try the simulator free at the link below.
๐ก THE KEY INSIGHT
โถ Writing the program is only Step 4 of the Five Steps
โถ Most of the work is the front-end planning that comes first
โถ Skip the front end and you don't save time โ you move it to the back end with interest
โถ That "interest" is endless rewrites, debugging, and rework
โถ Plan before you program to stop the rewrite cycle
๐ LEARN THE PROCESS โ PLC BEGINNERS GUIDE
accautomation.ca/programming/plc-beginners-guide
๐น๏ธ PLAN AND PROVE IT FIRST โ THE FREE ACC PLC SIMULATOR
accautomation.ca/simulator
๐ WHAT YOU'LL LEARN
โ Why endless rewrites come from skipping the planning
โ Why writing the program is only Step 4 of the process
โ Why the front-end planning is most of the work
โ Why skipping it moves the time to the back end with interest
โ Why planning before you program stops the rewrite cycle
โ FREQUENTLY ASKED
Q: Why is writing the program only Step 4?
A: Because most of the work in PLC development is the front-end planning that comes before you write code. Writing is just one step of the Five Steps. Skipping the planning is what causes endless rewrites.
Q: How do I stop endless rewrites?
A: Plan before you program. Do the front-end steps first, and prove your logic in a simulator before you build it for real, so you're not deferring the work to the back end with interest.
๐ Try the simulator free: accautomation.ca/simulator
๐ MORE RESOURCES
๐ฎ Free ACC PLC Simulator (plan and prove your logic, no install): accautomation.ca/simulator
โถ 10 Minutes on a Simulator Beats an Hour of Reading: youtube.com/shorts/BMoAvoA47lY
โถ PLC Programming Isn't Hard โ It's Dangerous: youtu.be/_TIHwDAIQo0
โถ PLC Beginners Guide: accautomation.ca/programming/plc-beginners-guide
โถ Free eBooks: accautomation.ca (subscribe for download)
๐ฌ Questions? Drop a comment below.
๐ New tutorials every Monday โ Subscribe and hit the bell!
#PLC #LadderLogic #IndustrialAutomation #PLCProgramming #ACCAutomation #PLCDesign #LearnPLC #PLCSimulator #FiveSteps #Shorts
Regards,
Garry
ACC Automation
accautomation.ca




![Fastest Way to Access Instructions! #PLCProgramming #Automation #Tutorial
Master Productivity PLC Boost Use Favorites Feature! [Tutorial] ๐ญ๐ช on the Productivity PLC. Step-by-step tutorial with real-world examples.
โก QUICK ANSWER
Modbus on the Productivity PLC maps remote coils and registers into local memory. Choose the port (Modbus RTU over RS-485 or Modbus TCP over Ethernet), match baud/parity/slave-ID on both ends, then use a read/write instruction to move holding registers and coils between devices.
๐ FULL STEP-BY-STEP + DOWNLOADS (project file, wiring diagrams, screenshots)
https://accautomation.ca/p1-m622-16dr-mini-plc-contact-and-coil-instructions/
๐ WHAT YOULL LEARN
โ
Productivity PLC Boost Use Favorites Feature! [Tutorial] ๐ญ๐ช step by step on the Productivity PLC
โ
Math instructions for calculations
โ
Data move and transfer instructions
โ
Real-world tips from manufacturing experience
โ FREQUENTLY ASKED
Q: RTU or TCP โ which do I use?
A: RTU runs over RS-485 serial; TCP runs over Ethernet. Pick whichever your device supports. Both are shown in the full guide.
Q: Why wonโt my Modbus device respond?
A: Confirm baud rate, parity, and slave ID match exactly, and check A/B wiring polarity on RS-485.
๐ Full step-by-step, code & wiring diagrams: https://accautomation.ca/p1-m622-16dr-mini-plc-contact-and-coil-instructions/
๐ MORE RESOURCES
โถ Series: https://accautomation.ca/series/productivity-plc/
โถ PLC Beginners Guide: https://accautomation.ca/programming/plc-beginners-guide/
โถ Free eBooks: https://accautomation.ca (subscribe for download)
๐ RECOMMENDED HARDWARE
โถ Shop: https://www.automationdirect.com/
โถ Parts Guide: https://www.accautomation.ca/purchase-find-parts/
๐ฌ Questions? Drop a comment below.
๐ New tutorials every Monday โ Subscribe and hit the bell!
#PLC #LadderLogic #IndustrialAutomation #PLCProgramming #ACCAutomation #ProductivityPLC #AutomationDirect #PLCTutorial #LearnPLC
Regards,
Garry
ACC Automation
http://www.accautomation.ca Fastest Way to Access Instructions! #PLCProgramming #Automation #Tutorial](https://i.ytimg.com/vi/J36YyCylIrI/mqdefault.jpg)





