Uploaded July 2026 | Updated November 2026, 3 days ago
Ferrules on stranded wire: why industrial electricians always crimp them onto PLC and terminal block connections for a reliable joint that won't work loose.
โก QUICK ANSWER
Industrial electricians almost always crimp a ferrule onto stranded wire before landing it in a PLC or terminal block, and there's a solid reason for it. Stranded wire is made of many fine strands, and when you clamp it bare into a screw terminal those strands can spread, splay or slowly compress over time. That leads to a connection that loosens โ and a loose connection on a control system means intermittent faults that are miserable to track down, plus extra resistance and heat at the terminal. A ferrule is a small metal sleeve crimped over the stripped end that binds all the strands into a single solid pin. The terminal then clamps onto that firm ferrule instead of loose strands, so the connection stays tight, no stray strands stick out to short against a neighbour, and the joint holds up to vibration and thermal cycling. It also makes for a noticeably tidier, more professional panel. It takes a few seconds per wire and prevents the kind of fault that costs hours later. The full wiring tutorial is in the guide below.
๐ฎ TRY IT FREE โ THE ACC PLC SIMULATOR
3D scenes, no install, right in your browser: accautomation.ca/simulator
๐ FULL WRITTEN TUTORIAL + DOWNLOADS (wiring & testing the P1-M622-16DR)
accautomation.ca/wiring-and-testing-our-p1-m622-16dr-practical-tutorial
๐ WHAT YOU'LL LEARN
โ What a ferrule is and why it goes on stranded wire
โ Why bare stranded wire works loose in a screw terminal
โ How a ferrule prevents loose connections, shorts and heat
โ Why the practice holds up to vibration and thermal cycling
โ Why it makes for a tidier, more professional panel
โ FREQUENTLY ASKED
Q: Why do electricians use ferrules on stranded wire?
A: A ferrule binds the fine strands into one solid pin, so the terminal clamps something firm instead of loose strands โ the connection stays tight, resists vibration, and won't work loose into an intermittent fault. The full tutorial is in the guide.
Q: Do you need ferrules on solid wire?
A: No โ solid wire is a single conductor that clamps firmly on its own. Ferrules are for stranded wire, where the individual strands would otherwise spread or compress in the terminal.
๐ Full wiring tutorial: accautomation.ca/wiring-and-testing-our-p1-m622-16dr-practical-tutorial
๐ MORE RESOURCES
๐ฎ Free ACC PLC Simulator (3D scenes, no install): accautomation.ca/simulator
โถ Productivity 1000 Series: accautomation.ca/series/productivity-1000-plc
โถ PLC Beginners Guide: accautomation.ca/programming/plc-beginners-guide
โถ Free eBooks: accautomation.ca (subscribe for download)
๐ RECOMMENDED HARDWARE
โถ Shop: automationdirect.com
โถ Parts Guide: accautomation.ca/purchase-find-parts
๐ฌ Questions? Drop a comment below.
๐ New tutorials every Monday โ Subscribe and hit the bell!
#PLC #LadderLogic #IndustrialAutomation #PLCProgramming #ACCAutomation #Ferrules #PLCWiring #ControlPanel #ProductivityPLC #Shorts
Regards,
Garry
ACC Automation
accautomation.ca
Ferrules on stranded wire: why industrial electricians always crimp them onto PLC and terminal block connections for a reliable joint that won't work loose.
โก QUICK ANSWER
Industrial electricians almost always crimp a ferrule onto stranded wire before landing it in a PLC or terminal block, and there's a solid reason for it. Stranded wire is made of many fine strands, and when you clamp it bare into a screw terminal those strands can spread, splay or slowly compress over time. That leads to a connection that loosens โ and a loose connection on a control system means intermittent faults that are miserable to track down, plus extra resistance and heat at the terminal. A ferrule is a small metal sleeve crimped over the stripped end that binds all the strands into a single solid pin. The terminal then clamps onto that firm ferrule instead of loose strands, so the connection stays tight, no stray strands stick out to short against a neighbour, and the joint holds up to vibration and thermal cycling. It also makes for a noticeably tidier, more professional panel. It takes a few seconds per wire and prevents the kind of fault that costs hours later. The full wiring tutorial is in the guide below.
๐ฎ TRY IT FREE โ THE ACC PLC SIMULATOR
3D scenes, no install, right in your browser: accautomation.ca/simulator
๐ FULL WRITTEN TUTORIAL + DOWNLOADS (wiring & testing the P1-M622-16DR)
accautomation.ca/wiring-and-testing-our-p1-m622-16dr-practical-tutorial
๐ WHAT YOU'LL LEARN
โ What a ferrule is and why it goes on stranded wire
โ Why bare stranded wire works loose in a screw terminal
โ How a ferrule prevents loose connections, shorts and heat
โ Why the practice holds up to vibration and thermal cycling
โ Why it makes for a tidier, more professional panel
โ FREQUENTLY ASKED
Q: Why do electricians use ferrules on stranded wire?
A: A ferrule binds the fine strands into one solid pin, so the terminal clamps something firm instead of loose strands โ the connection stays tight, resists vibration, and won't work loose into an intermittent fault. The full tutorial is in the guide.
Q: Do you need ferrules on solid wire?
A: No โ solid wire is a single conductor that clamps firmly on its own. Ferrules are for stranded wire, where the individual strands would otherwise spread or compress in the terminal.
๐ Full wiring tutorial: accautomation.ca/wiring-and-testing-our-p1-m622-16dr-practical-tutorial
๐ MORE RESOURCES
๐ฎ Free ACC PLC Simulator (3D scenes, no install): accautomation.ca/simulator
โถ Productivity 1000 Series: accautomation.ca/series/productivity-1000-plc
โถ PLC Beginners Guide: accautomation.ca/programming/plc-beginners-guide
โถ Free eBooks: accautomation.ca (subscribe for download)
๐ RECOMMENDED HARDWARE
โถ Shop: automationdirect.com
โถ Parts Guide: accautomation.ca/purchase-find-parts
๐ฌ Questions? Drop a comment below.
๐ New tutorials every Monday โ Subscribe and hit the bell!
#PLC #LadderLogic #IndustrialAutomation #PLCProgramming #ACCAutomation #Ferrules #PLCWiring #ControlPanel #ProductivityPLC #Shorts
Regards,
Garry
ACC Automation
accautomation.ca










