QCWDRSSTC Struggle Bus @Magneticitist
QCWDRSSTC Struggle Bus  @Magneticitist
Uploaded January 2026 | Updated November 2026, 3 hours ago
Finally picked this thing back up after like a year or something lol. Messing with this thing has been a good example of how small things one might not even consider can affect the performance. I spent a lot of time playing with this thing stuck to the idea that I should be able to replicate the results I got on a similar build even if I had to steal the coils from it etc. So I was looking for certain arcs at 170V ramps with not much more on the bus.
I was never able to do it on this build so now I'm trying again after cleaning up a little more than the LC tuning itself. I think at a certain point in the past I was realizing there were very specific adjustments I needed to make to the CD4046 feedback circuit to get the arcs I wanted. I don't really want to mess with some unknown variable there by just getting lucky with dials in precise spots so I'm just leaving the VCO window above the lower pole with 100khz or less of trim. Some of my issue in the past was dealing with random anomalies as a result of using the CD4046 circuit for feedback and not having it properly shielded. Since then I 3D printed a little box for it and covered it in aluminum tape (keeping continuity with folds) and grounding it to the control power negative. My driver will also do this making that node a star ground. It has been really consistent ever since with no random oopsies out of nowhere.

Now I need to just start sticking with certain tunes and running the tests at 300VDC bus voltage. Part of why I'm still hesitant to do that is because I don't have true control power isolation as of yet because I still need to add a suitable isolated DC to DC converter for the buck driver power. Without that everything is "fine" until a failure, at which point all depending, I could lose some control stuff in the process. I think in the mean time I'll just split the rails and use my current DC supply for the main control power, and a separate battery DC supply just for the buck driver. The switches were also pretty dang expensive so I'll happily crank them so long as I'm sure I'm not about to destroy them. It just makes me feel better about it when I can land on a tuning that gives me very straight sparks as opposed to wild gnarly ones.

This build is still using Finn Hammer's arduino ramp code and a basic battery powered interrupter all open loop.
Just a beefed up Steve Ward DRSSTC driver and separate driving IC for the buck converter. The OCD is currently set with a burden resistor that doesn't allow me to crank the OCD trip higher than about 100A or so. So based on that and not even having it all the way up, I'm probably far too detuned to really ramp the current up that high as of now. I think in the build I was hitting 4ft with, my OCD was occasionally tripping around the 200-250A region. It may not have been accurate but it was surely around ~180-200A. Now I'm using a 32 turn CT and will drop the burden to about ~2 ohms to set a max of like ~180A-200A for this one. If I had to guess I haven't really seen peaks above about 80A with this one yet so it's probably not really dual resonant enough to call it that.
QCWDRSSTC Struggle BusBig Rock 3s FPV Sensored ESC/Motor 2400Kv Quick TestRC Car FPV O3 Air Unit + 2.4g Control, Neighborhood Obstruction TestTyphon 3s FPV Hobbywing Sensored 3200Kv + Max10 140A ESCQCW Driver + Bricks First Test ~300khzRC CAR FPV DJI O4 w/ Goggles 3 First Tests and ComparisonsBudget QCW Test 200VDC RampsQCWDRSSTC Double Full Bridge RetuningDJI O4 Pro FPV + Fireteam 6s + HEQ GimbalMore Steve Ward HFSSTC TestingRC FPV Exploring DJI O3 + Crossfire (O3 footage)RC Digital FPV Adding Live Audio (~750mhz)
Magneticitist |

QCWDRSSTC Struggle Bus

SHARE TO X SHARE TO REDDIT SHARE TO FACEBOOK WALLPAPER