Uploaded October 2023 | Updated November 2026, 3 hours ago
This is a 15-20VDC QCWSSTC to where I have this push button turning a ZVS driver on to charge the buck capacitors.
These are not super long ramps but I figure it's probably a good real world example of what can be done with just a random SSTC not really intended to run QCW ramps, and 200V or so peaks at around 8-10ms on times from a buck converter made like this. Ideally that large cap wouldn't be there and it would be done with small ones to create an overall smaller build.
I'm kind of just using a random ZVS driver I made that has 55v fets so I decided on 15V-18 input. It would be better to use 20V or so input so that same 20V can ensure the buck and SSTC drive is able to deliver at least 15V after the regulators, and that's about what you'll get from a fresh charged lithium drill battery.
Had to change up my LC filter because the inductor was saturating too easily. This new one consisting of some cheap yellow/white cores stacked together seems to work out well for the power I'm pushing. It's probably just barely suitable for the other full bridge I'm trying to get running again.
The larger capacitor I added was not really necessary for this half bridge test circuit, only for the PLL full bridge. That one is using a new PLL circuit I made since I snatched its original one for my first QCW. When rebuilding the circuit I used different values for the potentiometers which was throwing me off. It still doesn't seem to run properly so I think I must have had some very specific tuning previously.
What you need to build this:
Finn Hammer's Ramp Generator (Arduino UNO)
FGA60N65SMD (buck high side switch)
APT75DQ60BG (buck blocking diode)
600V 20uF Film Capacitor (for buck LC)
These 2 stacked together and wound for 120uH (maybe 50 turns?) amazon.com/dp/B0BS8QC3BX?psc=1&ref=ppx_yo2ov_dt_b_product_details (buck LC)
5K 5-10W resistor (load resistor for buck output)
HCPL-3120 (To drive IGBT gate)
2000uF 300V in Electrolytics (more would be better but even 1000uF would work)
250-500khz Half Bridge SSTC with interrupter input (no large smoothing caps on bus)
This is a 15-20VDC QCWSSTC to where I have this push button turning a ZVS driver on to charge the buck capacitors.
These are not super long ramps but I figure it's probably a good real world example of what can be done with just a random SSTC not really intended to run QCW ramps, and 200V or so peaks at around 8-10ms on times from a buck converter made like this. Ideally that large cap wouldn't be there and it would be done with small ones to create an overall smaller build.
I'm kind of just using a random ZVS driver I made that has 55v fets so I decided on 15V-18 input. It would be better to use 20V or so input so that same 20V can ensure the buck and SSTC drive is able to deliver at least 15V after the regulators, and that's about what you'll get from a fresh charged lithium drill battery.
Had to change up my LC filter because the inductor was saturating too easily. This new one consisting of some cheap yellow/white cores stacked together seems to work out well for the power I'm pushing. It's probably just barely suitable for the other full bridge I'm trying to get running again.
The larger capacitor I added was not really necessary for this half bridge test circuit, only for the PLL full bridge. That one is using a new PLL circuit I made since I snatched its original one for my first QCW. When rebuilding the circuit I used different values for the potentiometers which was throwing me off. It still doesn't seem to run properly so I think I must have had some very specific tuning previously.
What you need to build this:
Finn Hammer's Ramp Generator (Arduino UNO)
FGA60N65SMD (buck high side switch)
APT75DQ60BG (buck blocking diode)
600V 20uF Film Capacitor (for buck LC)
These 2 stacked together and wound for 120uH (maybe 50 turns?) amazon.com/dp/B0BS8QC3BX?psc=1&ref=ppx_yo2ov_dt_b_product_details (buck LC)
5K 5-10W resistor (load resistor for buck output)
HCPL-3120 (To drive IGBT gate)
2000uF 300V in Electrolytics (more would be better but even 1000uF would work)
250-500khz Half Bridge SSTC with interrupter input (no large smoothing caps on bus)










