How to make a Ball Socket Cutter Tool and use it @keithnoneya
How to make a Ball Socket Cutter Tool and use it  @keithnoneya
Uploaded July 2017 | Updated November 2026, 1 day ago
Description: Hey guys I had to make a tool for a Ball Socket to hold a swivel ball on a plate that held a Thermistor Sensor. The sensor is for an aircraft Windshield Heater Test Set. The sensor had to sit flat on the windshield so this part had to be fixed.
I approached the problem by:

A. Making a Ball Socket Cutter tool:
- 1st. I made a ball, on the end of the rod, slightly smaller that the ball the socket that was going to be used. That way when the swivel ball was placed into the socket it would fit snug with no play.
- 2nd. Looking at the top/end of the ball I ground 3/4's of the ball off the sides then cut half the bottom off the the remaining 1/4 section.
- 3rd. I cut the very tip off the end of the ball at a 45 deg angle as an inner relief so I didn't end up with a flat bottom when the tool was inserted all the way for the cut.
- 4th. I cut a low channel right up to the outer edge of the remaining portion of the ball as a cutting edge.
- 5th. I cut a relief on the shaft behind the ball to ensure it did not cut into the top of the socket.
- 6th. Optional: If you are going to use the tool to cut a metal socket you'll have to harden it then temper it. Also if you plan on using a metal socket you have to cut slits across the hole in a few spots to allow the metal to expand when the ball is pushed into the socket. Otherwise the socket or ball could be damaged.

B. Determine Ball Socket Depth:
- 1st. Figure the depth that you want the ball to sit into the socket. you do this by:
a. Figure the thickness of the wall that you want the socket to have.
b. Figure the size of the ball you're going to use, then add the two measurements, this is the depth of the hole for the socket that you'll have to cut for the ball to bottom out in.

C. Drilling the pilot hole for the Ball Cutter Tool"
a. Using the measurement from step B drill a hole to the depth
into the material you plan to make the ball socket out of.

D. Figuring How far to move the cross slide:
a. Divide the previous wall thickness by 2.

E. Aligning the tool for Cutting the socket;
a. Place the tool up against the end of the work piece next to the Pilot hole and center the top of the tool cutting edge half way up the thickness of the work piece or the center of the pilot hole.
b. Move the tool over the hole and place the tool into the pilot hole and bottom it out on the bottom of the hole.
c. Align the cutting edge up against the wall of the pilot hole.
d. Set the Cross-Slide dial to zero.

F. Cutting the Socket:
a. Back the tool slightly away from the edge of the pilot hole to ensure the tool is not snapped off when the chuck is engaged.
b. Start and Engage the Lathe chuck then using the cross slide move the tool and cut to the socket to depth of 1/2 the wall thickness determined in step D.
c. Using the cross slide move the cutting tool back to the center of the pilot hole and turn the lathe off.
d. Using the Table control move the tool away and out of the Pilot hole. You now have a Ball Socket.

G. Finish the Ball Socket by putting a 45 deg countersink relief in the Socket hole so that the ball can swivel. Then parting it off and cutting and tapping your mounting holes.
I hope you enjoyed the video. Thanks for watching. If you learned something or would like to comment please do. If you would like to help my channel please subscribe.
Best Wishes n Blessings. Keith
How to make a Ball Socket Cutter Tool and use itHow to Connect and Leak Test an Argon Bottle to Your Welder Part 2How to remove Permanent Marker from metal and plastics2003 Cadillac CTS Drivers Quarter Spraying Glossy Clear Coat Part 42 of99-03  7.3L F250 F350 Alternator Change Step by Step2003 Cadillac CTS Rear Window Back In Part 45How to clean your Pinball Machine Playing Field and change Your Bumpers Part 42003 Cadillac CTS Drivers Quarter Panel 95% Welded  Part 11 ofHow to clean your Pinball Machine Playing Field and change Your Bumpers Part 7TDS3054 Signal Switching Relay ASLD4.5W K on the H2587G AttenuatorHow to tell if your Nissan CVT is going bad 2014 Murano Slipping2003 Cadillac CTS Drivers Quarter Panel Trim n Fit Part 3 of ?
Keith Noneya |

How to make a Ball Socket Cutter Tool and use it

SHARE TO X SHARE TO REDDIT SHARE TO FACEBOOK WALLPAPER