Binding & Working Modes of R16F @Radiolink_official
Binding & Working Modes of R16F  @Radiolink_official
Uploaded October 2024 | Updated November 2026, 5 days ago
RadioLink T16D comes with a R16F receiver. They are bound at the factory. So there is no need to re-bind them when you receive it. But if you buy a new R16F receiver. You need to bind it to the transmitter. I’m going to show how to bind R16F to T16D.
There are 2 steps for binding.
1.Select receiver protocol.
2.Bind.

First, Enter MAIN menu--Receiver settings--RF settings--make sure the module selection is set to internal. And for protocol, R16F supports FHSS V1, V2 and V2.1. FHSS V1 and V2 protocols support 8 channels, but FHSS V2.1 protocol supports 16 channels. When using R16F, if FHSS V1 or FHSS V2 protocol is selected, only 8 channels are available on the receiver. So it is recommended to select FHSS V2.1 protocol.
For details of the receiver protocols and compatible receivers, please refer to the table on the screen:

Now, bind them.
1.Power on the transmitter and the receiver. The flashing LED of the receiver indicates there is no binding between the the transmitter and the receiver. And also there is no signal tower on the screen of T16D.
2. Keep a distance of about 30cm between the transmitter and receiver.
3. There is a tiny black binding button between the two antennas. Press and hold it until the LED flashes fast.
4. The solid light of the receiver indicates the binding is complete, and the signal tower on the screen of the transmitter shows the binding is successful. If binding fails, the LED of the receiver will keep flashing slowly, please repeat the binding steps.
Once their binding succeeds, it will be stored.

Then let’s talk about the working modes of R16F. R16F supports three signal outputs: PWM, SBUS and CRSF. It has four working modes in total.
For working modes switch, we have 2 methods:
(1)Turning on/off the SBUS: Short press the binding button once to turn on/off the SBUS. Blue LED indicates the SBUS is turned on.
(2)Turning on/off the CRSF: Short press the binding button twice within 2 seconds to turn on/off the CRSF. Green LED indicates the CRSF is turned on.

Let’s check the four working modes. The signal LED here can show you the current working mode.
1.Red LED always on indicates PWM signal output, 16 channels in PWM signal.
2.Short press the binding button once to turn on the SBUS signal. Red and blue LED always on indicates PWM+SBUS signals output.
3.Short press the binding button twice to turn on the CRSF. Red, green, and blue LED always on indicates PWM+CRSF+SBUS signals output.
Short press the binding button once to turn off the SBUS signal. Red and green LED always on indicates PWM+CRSF signals output.

For more details of R16F, please refer to the link:
radiolink.com/r16f

For more details of T16D, please refer to the link:
radiolink.com/t16d

If any question about RadioLink products please feel free to contact us. Our email is: after_service@radiolink.com.cn

#transmitter #radiolink
Binding & Working Modes of R16FEasy to change the Radiolink RC8X Home Screen Wallpaper!!!Radiolink F108 | Optical Flow PosHold FPV Racing DroneThrottle curve Function of RC8XHow to flash INAV firmware on F722/F405?How to Set T16D/T12D to Control D460?Setup and Connect Walksnail Digital FPV System to crossflight/Mini Pix/PIXHAWKRadioLink F722 Flight Controller Automation Software TestingT16D/T8FB Trainer Function with Wireless Trainer CableThrottle Hold Function of T8S/T8FB TransmitterBinding & Working Modes of R12FHow to Replace the Joystick and Calibrate the Joystick of T8S Transmitter?
RadioLink |

Binding & Working Modes of R16F

SHARE TO X SHARE TO REDDIT SHARE TO FACEBOOK WALLPAPER