Uploaded March 2025 | Updated November 2026, 5 hours ago
Binding and Working Modes of R12DSE
R12DSE is a mini receiver, which is compatible with RadioLink AT10II, AT10, AT9S Pro, AT9S, AT9. So I take AT9S Pro transmitter as an example in this tutorial.
There are 2 steps for binding.
1.Set the transmitter.
2.Bind.
First, Enter Basic menu--PARAMETER. Make sure RF-MODE is turned on. If RF-MODE is turned off, no receiver can be bound to AT9S Pro.
Then, Enter Basic menu--system--Set CH-SELECT.
Since R12DSE is a 12-channel receiver. We need to Set CH-SELECT to 12CH. If it is selected as 10CH, the servos will vibrate and cannot work well.
After the setting, bind them.
Place the transmitter and R12DSE receiver more than 30 centimeters apart.
Power on the transmitter and the receiver R12DSE.
R12DSE must work with a flight controller. After connecting to the flight controller, the flight controller will supply power to the receiver. I don’t connect the flight controller here, so I use a lipo battery. The working Voltage of R12DSE is 3-6V, so I can use 1S lipo battery. Make sure the polarity is not reversed.
(Note: The Operating Voltage of R12DSE is 3-6V. 2S lipo battery cannot be used to supply power to R12DSE.)
There is no signal tower on AT9S Pro now, because they are not bound.
Here is the binding button of the receiver. Long Press the binding button. The LED indicator of will flash fast.
When the LED indicator goes solid, binding is complete. We can see the signal tower on the screen of R12DSE, which means binding is successful. If binding fails, the LED of the receiver will keep flashing slowly, please repeat the binding steps.
Then. I/m going to introduce the working modes of R12DSE.
R12DSE has two working modes.
1.SBUS signal, 12 channels in SBUS, with Purple/Blue LED.
2.PPM signal, 12 channels in PPM, with Red LED.
The LED of R12DSE is red now, which indicates PPM signal.
How to switch the signals?
You just need to short press the binding button twice within 1 second to switch the signal.
So I short press the binding button twice. Red LED turns into blue/purple LED, which indicates it is SBUS signal now.
You can short press binding button twice again to switch to PPM signal.
So that’s all about the introduction of the binding and working modes of R12DSE.
For more details of R12DSE:
radiolink.com/r12dse
Purchase link of R12DSE:
radiolink.com/r12dse _where_to_buy
If any question about RadioLink products please feel free to contact us. Our email is: after_service@radiolink.com.cn
#rcplane #receiver
Binding and Working Modes of R12DSE
R12DSE is a mini receiver, which is compatible with RadioLink AT10II, AT10, AT9S Pro, AT9S, AT9. So I take AT9S Pro transmitter as an example in this tutorial.
There are 2 steps for binding.
1.Set the transmitter.
2.Bind.
First, Enter Basic menu--PARAMETER. Make sure RF-MODE is turned on. If RF-MODE is turned off, no receiver can be bound to AT9S Pro.
Then, Enter Basic menu--system--Set CH-SELECT.
Since R12DSE is a 12-channel receiver. We need to Set CH-SELECT to 12CH. If it is selected as 10CH, the servos will vibrate and cannot work well.
After the setting, bind them.
Place the transmitter and R12DSE receiver more than 30 centimeters apart.
Power on the transmitter and the receiver R12DSE.
R12DSE must work with a flight controller. After connecting to the flight controller, the flight controller will supply power to the receiver. I don’t connect the flight controller here, so I use a lipo battery. The working Voltage of R12DSE is 3-6V, so I can use 1S lipo battery. Make sure the polarity is not reversed.
(Note: The Operating Voltage of R12DSE is 3-6V. 2S lipo battery cannot be used to supply power to R12DSE.)
There is no signal tower on AT9S Pro now, because they are not bound.
Here is the binding button of the receiver. Long Press the binding button. The LED indicator of will flash fast.
When the LED indicator goes solid, binding is complete. We can see the signal tower on the screen of R12DSE, which means binding is successful. If binding fails, the LED of the receiver will keep flashing slowly, please repeat the binding steps.
Then. I/m going to introduce the working modes of R12DSE.
R12DSE has two working modes.
1.SBUS signal, 12 channels in SBUS, with Purple/Blue LED.
2.PPM signal, 12 channels in PPM, with Red LED.
The LED of R12DSE is red now, which indicates PPM signal.
How to switch the signals?
You just need to short press the binding button twice within 1 second to switch the signal.
So I short press the binding button twice. Red LED turns into blue/purple LED, which indicates it is SBUS signal now.
You can short press binding button twice again to switch to PPM signal.
So that’s all about the introduction of the binding and working modes of R12DSE.
For more details of R12DSE:
radiolink.com/r12dse
Purchase link of R12DSE:
radiolink.com/r12dse _where_to_buy
If any question about RadioLink products please feel free to contact us. Our email is: after_service@radiolink.com.cn
#rcplane #receiver










