Uploaded July 2023 | Updated November 2026, 3 hours ago
Got rid of some stuff and got a Big Rock for future long range FPV on the ground. I decided to mount everything on the body because it's fairly strong. Need to adjust some things but I think with this setup I don't have to worry about water ingress or getting stuck in tall grass. Being able to get up curbs also makes a lot more things accessible. A crawler can do that but a crawler will have a hard time outrunning a person. There is lots of space inside the body for stuff and it was easy to cleanly route wires and connectors.
The downside is I have to limit the throttle to around 75% to avoid flipping it and destroying the camera rig. I'll probably move to a different pan/tilt assembly at some point because this one has too much play in it. The servos as well. Have to find servos with no play or wiggle. I also needed to play with the wheels a little bit to get them from going weeble wobble. Just shifting around their orientation on the wheel nut can often balance out imbalance. The truck came with the wheels aggressively toe-out to help with steering but I made them more straight so it won't try to veer off when going fast. Definitely handles better and keeps straighter at high speed than the other budget deals I have.
So far I seem to have fairly identical results on both rigs using the O3. I can tell I have slightly better range on the rig using the TrueRC antennas 1 LHCP and 1 RHCP. The way all my setups work now is I have the one RC6GS transmitter and crossfire receivers on the cars. I can store the settings for each car in the RC6GS and just switch to which car I'm controlling before turning on the crossfire transmitter. Nano receivers work really well but I've found 6 channels a little limiting. That gives me steering, throttle, cam tilt, cam pan, DJI arm channel, and a flashlight. If I want to add anything else like a horn I'd need a different receiver, and I can only add one more channel anyway with the RC6Gs because it can control 7 total.
The way I set the O3 up this time is using a 3S lipo supply, then an 8V linear regulator to power a 6V fan attached to a small heatsink on the unit. It might require more than that on hot days. The O3 is armed using an arduino nano again (using code created by Richard Amiss). I use an LM317T and an aux On/Off circuit to power it for the flashlight. I set the LM317T voltage to around 3.5V or so and rely on the flashlight internal driver to regulate the current. Since the O3 still sucks in low lighting you pretty much need a light that can track where you're looking. This one doesn't have audio yet so I might add a 1.3g vtx to it like I did my other one.
At around @6:05 you can see a random zombie that early morning who decided to walk up close to where I was parked. He was probably just walking that path, but it's a tiny path located in a private business lot and you have to walk a good ways to get to it. It's just an example of how there is always somebody nearby. It's obvious what I'm doing there, but not so obvious what any of these random people are doing at any given time. Some of them probably don't like the idea of another person using that space for filming so they'll call the cops and try to have it all for themselves.
Got rid of some stuff and got a Big Rock for future long range FPV on the ground. I decided to mount everything on the body because it's fairly strong. Need to adjust some things but I think with this setup I don't have to worry about water ingress or getting stuck in tall grass. Being able to get up curbs also makes a lot more things accessible. A crawler can do that but a crawler will have a hard time outrunning a person. There is lots of space inside the body for stuff and it was easy to cleanly route wires and connectors.
The downside is I have to limit the throttle to around 75% to avoid flipping it and destroying the camera rig. I'll probably move to a different pan/tilt assembly at some point because this one has too much play in it. The servos as well. Have to find servos with no play or wiggle. I also needed to play with the wheels a little bit to get them from going weeble wobble. Just shifting around their orientation on the wheel nut can often balance out imbalance. The truck came with the wheels aggressively toe-out to help with steering but I made them more straight so it won't try to veer off when going fast. Definitely handles better and keeps straighter at high speed than the other budget deals I have.
So far I seem to have fairly identical results on both rigs using the O3. I can tell I have slightly better range on the rig using the TrueRC antennas 1 LHCP and 1 RHCP. The way all my setups work now is I have the one RC6GS transmitter and crossfire receivers on the cars. I can store the settings for each car in the RC6GS and just switch to which car I'm controlling before turning on the crossfire transmitter. Nano receivers work really well but I've found 6 channels a little limiting. That gives me steering, throttle, cam tilt, cam pan, DJI arm channel, and a flashlight. If I want to add anything else like a horn I'd need a different receiver, and I can only add one more channel anyway with the RC6Gs because it can control 7 total.
The way I set the O3 up this time is using a 3S lipo supply, then an 8V linear regulator to power a 6V fan attached to a small heatsink on the unit. It might require more than that on hot days. The O3 is armed using an arduino nano again (using code created by Richard Amiss). I use an LM317T and an aux On/Off circuit to power it for the flashlight. I set the LM317T voltage to around 3.5V or so and rely on the flashlight internal driver to regulate the current. Since the O3 still sucks in low lighting you pretty much need a light that can track where you're looking. This one doesn't have audio yet so I might add a 1.3g vtx to it like I did my other one.
At around @6:05 you can see a random zombie that early morning who decided to walk up close to where I was parked. He was probably just walking that path, but it's a tiny path located in a private business lot and you have to walk a good ways to get to it. It's just an example of how there is always somebody nearby. It's obvious what I'm doing there, but not so obvious what any of these random people are doing at any given time. Some of them probably don't like the idea of another person using that space for filming so they'll call the cops and try to have it all for themselves.










