80/20: 15 Series Access Hole Drill Jig (6075) @8020llc

Uploaded November 2024 | Updated September 2026, 1 week ago

To Purchase: bit.ly/3VebOQU
Find in Catalog: bit.ly/428g7iZ
80/20 Website: bit.ly/3peM7n3

Jig for 1515 Profiles. Note: This part does not come with drill bit.

80/20: 15 Series Access Hole Drill Jig (6075)

AutoQuoter Solidworks: Create CM/User Parts

$80/20: Detent Hinges Overview To Purchase: https://bit.ly/3OPZ80S Find in Catalog: https://bit.ly/428g7iZ 80/20 Website: https://bit.ly/3peM7n3 Hello, and welcome to 80/20’s product highlight series. Today we’ll be taking a look at Detent Hinges. These hinges are great for holding doors open at different angles. They are easy to install, available in both fractional and metric, and compatible across a wide range of profile series. Now one thing to keep in mind when using a detent hinge, is that your panel is going to need a drill through service. Now you’re also going to need a bolt assembly too. More information on 80/20’s machining services and recommended bolt assemblies can be found in the 80/20 product catalog. Alright, so when it comes to installing our detent hinge. We’re going to start with the stopper. We’re going to move it into position. Grab our wrench, and tighten that down. That’s going to help hold our panel into place while we are installing it. So we’ll go ahead and set that off to the side again. Now we’re going to work on putting the hinge on the panel itself. We got one bolt in there, so we’ll take one more bolt and finish it off. Grab our washer, and out hex nut. We’ll hand tighten all that down. We’ll grab our wrenches. And we’ll tighten that the rest of the way down. Now once we’re done with that side. We’ll preload the T-slot side with one more bolt, and one more T-nut. Now once we have that done, we’re ready to put it on our frame. So we’ll grab our frame and lay it flat here. We’ll get our hinge lined up and just slide the T-nuts into the open T-slot. We’ll move that into position. We’ll that flat and that stopper will hold that into place for us while we tighten that down. Now one last option you’ll want to consider is cover caps. They simply go right over the bolts, and snap into place for a nice smooth finish. Now hopefully you found this segment on detent hinges helpful. For more information please visit 80/20.net and be sure to subscribe to future 80/20 videos. And as always, make it a great day.$

80/20: 40 Series Anchor Fastener (40-3373)

80/20: 10 Series 2-Hole Slotted Inside Corner Bracket (4265)

80/20: 15 Series 4-Hole Tall Gusseted Inside Corner Bracket (4336)

$80/20: Central Connector Overview To Purchase: https://bit.ly/3J7hxCW Find in Catalog: https://bit.ly/428g7iZ 80/20 Website: https://bit.ly/3peM7n3 Hello, and welcome to 80/20s product highlight series. Today we are going to take a look at the central connector. This fastening method is a great choice for a strong connection with adjustability. Its available in fractional, metric, and compatible across a wide range of profile series. Now the central connector comes in three parts. You have the bolt, the barrel nut, and the spring. Now one thing youll want to keep in mind when using the central connector, is one of your bars is going to need machined with a counterbore service, and a hole drilled in the center cavity. More information on central connector machining services can be found in the 80/20 product catalog. Now when it comes to installing the central connector, youree going to start with your barrel and place it into the counterbore service, making sure the hole faces out towards the end of the profile. Next well take our bolt, place the spring over it. From there well take our bolt and place it in the center cavity with the indent facing up towards the barrel. Well line it up, and slightly engage it with our wrench. From there well take the other bar, and slide the connector in. Find our desired location, and tighten down with our wrench. Now the great thing about the central connector, is its adjustability. If you need a new location on the bar, simply loosen up the central connector, find your new location on the bar, and tighten down firmly again. Once you have that tightened down, you have a strong, flush connection. Hopefully you found this segment on the central connector helpful. For more information, visit 8020.net and make sure to subscribe to future 80/20 videos. And as always, make it a great day.$

80/20: 30 Series Anchor Fastener (13186)