80/20: Lateral Roller Guide (R40-GUIDE) @8020llc

Uploaded April 2024 | Updated September 2026, 1 week ago

To Purchase: bit.ly/3VYUJfI
Find in Catalog: bit.ly/428g7iZ
80/20 Website: bit.ly/3peM7n3

-Sold at 96" (2.438 meter)
-Works with Steel Roller Track Narrow

80/20: 10 Series 2-Hole Slotted Inside Corner Bracket (4265)

80/20: 15 Series 4-Hole Tall Gusseted Inside Corner Bracket (4336)

$80/20: Central Connector Overview To Purchase: https://bit.ly/3J7hxCW Find in Catalog: https://bit.ly/428g7iZ 80/20 Website: https://bit.ly/3peM7n3 Hello, and welcome to 80/20s product highlight series. Today we are going to take a look at the central connector. This fastening method is a great choice for a strong connection with adjustability. Its available in fractional, metric, and compatible across a wide range of profile series. Now the central connector comes in three parts. You have the bolt, the barrel nut, and the spring. Now one thing youll want to keep in mind when using the central connector, is one of your bars is going to need machined with a counterbore service, and a hole drilled in the center cavity. More information on central connector machining services can be found in the 80/20 product catalog. Now when it comes to installing the central connector, youree going to start with your barrel and place it into the counterbore service, making sure the hole faces out towards the end of the profile. Next well take our bolt, place the spring over it. From there well take our bolt and place it in the center cavity with the indent facing up towards the barrel. Well line it up, and slightly engage it with our wrench. From there well take the other bar, and slide the connector in. Find our desired location, and tighten down with our wrench. Now the great thing about the central connector, is its adjustability. If you need a new location on the bar, simply loosen up the central connector, find your new location on the bar, and tighten down firmly again. Once you have that tightened down, you have a strong, flush connection. Hopefully you found this segment on the central connector helpful. For more information, visit 8020.net and make sure to subscribe to future 80/20 videos. And as always, make it a great day.$

80/20: 30 Series Anchor Fastener (13186)

$80/20: Flat Plates Overview To Purchase: https://bit.ly/3J0UhXh Find in Catalog: https://bit.ly/428g7iZ 80/20 Website: https://bit.ly/3peM7n3 Hello, and welcome to 80/20s product highlight series. Today were going to take a look at the flat plates. 80/20s flat plates are not only easy to install, but also require no machining. They come in fractional, metric, and are available across a wide range of profile series. When using it, you have a choice. A flat plate can be used for a stand-alone fastening method, or to reinforce another fastening method. Here you can see a small sample of the many flat plates that 80/20 offers. As you can see, the plates come in a wide variety of shapes, and sizes, making it one of the more versatile fastening methods 80/20 offers. Now one thing youll want to keep in mind when using the flat plate is, youll need bolt assemblies to install it. Recommended bolt assemblies for all flat plates, can be found in the 80/20 product catalog. Now when it comes to installing the flat plate, the first thing youll want to do is preload your hardware. Preloading not only makes it easier to install your flat plate, but also saves time during assembly. To save additional time and money, youll want to look for opportunities where you can substitute out a single T-nut, for double and triple T-nuts, like in this example. Now to get started, well take our plate with the preloaded hardware on it, and finish it up by putting the last bolt in it. Well take our T-nut and put it on. Now, youll want to make sure when using the T-nut, you have the pilot hole facing downwards. Well get that on there. At this point were ready for our bars. Well slide the flat plate on. Well take our other bar, get it on there. Once we have all that on there, well take our wrench and tighten down each bolt. Once we have that tightened, we have a strong, secure connection. Now hopefully you found this segment on the flat plate helpful. For more information, visit 8020.net and make sure to subscribe to future 80/20 videos. And as always, make it a great day.$

80/20: 15 Series Access Hole Drill Jig for 1530 Profiles (6130)

80/20: End Cap with Push-In Fastener (2030-PLAIN)

80/20: 10 Series Bolt Assembly 1/4-20 x .375 Black FBHSCS & Slide-In Economy T-Nut (3386)

$80/20: Deadbolt Latch Overview To Purchase: https://bit.ly/44KLYHq Find in Catalog: https://bit.ly/428g7iZ 80/20 Website: https://bit.ly/3peM7n3 Hello and welcome to 80/20’s product highlight series. Today we are going to take a look at deadbolt latches. These latches are perfect for guarding and enclosure applications. They are easy to install and available in both fractional and metric. Now one great thing about this latch is that it requires no machining, and comes with all recommended mounting hardware. Now to get started, we are going to finish preloading our bolt side with one last bolt and one last T-nut. Now it’s important to note that when you’re putting on the T-nut, to have the pilot projection facing away from the bolt. Get that on there. We’ll just take our frame here. We’ll slide it into the open T-slot, find where we want to put it, and take our wrench and tighten it down. Now we’ll just take the latch side and slide it into the other open T-slot. We’ll line it up with our bolt, and we’ll latch it together. Once we have the latched together, we’ll go ahead and tighten down the latch side. Now once you have that tightened down, you have a strong secure connection. Now it’s worth noting that this latch also comes in a 90 degree style, which is going to prevent any snagging on your lever when it’s engaged. Now hopefully you found this segment on deadbolt latches helpful. For more information please visit 80/20.net and make sure to subscribe to future 80/20 videos. And as always, make it a great day.$

80/20: R85 Track Mount Drop Stop (R85-DS)