80/20: 10 Series 3-Hole Inside Corner Bracket (4176) @8020llc

Uploaded November 2024 | Updated September 2026, 1 week ago

To Purchase: bit.ly/48562Hd
Find in Catalog: bit.ly/428g7iZ
80/20 Website: bit.ly/3peM7n3

The 3-hole inside corner bracket is an external fastening method that creates a 90-degree connection. There are two stacked holes on one side and one hole on the opposite side of the bracket. This fastener requires no machining services and can provide infinite positioning along the profile T-slot, allowing a large degree of adjustability. The 3-hole inside corner bracket engages the 2-degree drop-lock feature when the assembly bolts are tightened to the required torque. It is a fastening method that can be repositioned and reused.

80/20: 10 Series 3-Hole Inside Corner Bracket (4176)

$80/20: Pivot Plate Overview To Purchase: https://bit.ly/44LBTuH 80/20 Website: https://bit.ly/3peM7n3 Find in Catalog: https://bit.ly/428g7iZ Hello, and welcome to 80/20s product highlight series. Today were going to take a look at the pivot plates. This connector allows bars to be positioned at various angles. Theyre easy to install, require no machining, and are available in both fractional and metric. Now one thing youre going to want to keep in mind with the pivot plate, is that its a stand alone part, and bolt assemblies will be required to install it. More information on 80/20s bolt assemblies can be found in the 80/20 product catalog. Now when it comes to installing the pivot plate, the first thing youre going to want to do is preload your hardware. Preloading not only makes it easier to install your plates, but also saves time during assembly. Now to finish up, Im going to put one last bolt and one last T-nut into this plate. Now its important when youre using your T-nuts to have pilot projections facing downwards, or away from the plate. Get that preloaded on there, well take our bar, slide the plate on. Now well hold that into place, and grab our other bar, and line up the center holes. Once we have those lined up, well take our center bolts, one by one, and feed them through. Well get that one on there with a hex nut, well hand-tighten it down, and well do the same thing on the back. Well get a bolt, feed it through, get a hex nut on it and hand-tighten it down as well. Now once youve got those on there, well go back to that plate we put on, and tighten it down the rest of the way. Once weve got that secure, the last thing weve got to do is find our desired angle we want. That looks just about right, well take our other wrench, and tighten down those center bolts. Well get that in there for a secure connection. Now hopefully you have found this segment on the pivot plate helpful. For more information visit 8020.net and make sure to subscribe to future 80/20 videos. And as always, make it a great day.$ $80/20: Floor Anchors Overview To Purchase: https://bit.ly/3NpEuCD Find in Catalog: https://bit.ly/428g7iZ 80/20 Website: https://bit.ly/3peM7n3 Hello and welcome to 80/20’s product highlight series. Today we’re going to take a look at floor mounts. These floor brackets are great for securing projects to the floor. They’re easy to install, available in both fractional and metric, and require no machining. However, a bolt assembly will be needed. More information on 80/20’s recommended bolt assemblies, can be found in the 80/20 product catalog. Now before we get started. I wanted to point out that our floor brackets have a variety of styles to them. We have our standard style, and then we have a version of that one that allows you to adjust the height a little bit more. We have a baseplate style, and one without a baseplate. Now the great thing about all these is, is that they install all the same way. Now for today we’re going to use the standard one. We’re just going to finish it up with one last bolt and one last Tnut. Now you want to make sure with the Tnut, you have the pilot projection on it facing away from the bracket. So we’ll just preload that onto the bolt there. Once we have that on there, we’ll take our extrusion. We’ll slide the bracket right onto it, we’ll get it into position, and we’ll tighten down with our wrench. Now once you have that tightened, your bracket is nice and secure. Now one last thing we want to show you, is a version where you can adjust the height a little bit more. Now the only difference is, the profile is going to rest on this Tnut on the back side. Now if you want to adjust the height, you simply take this bolt on the front side. Take your wrench, and raise or lower to the desired height that you need. Now hopefully you found this segment on floor mounts helpful. For more information please visit 8020.net and make sure to subscribe to future 80/20 videos. And as always, make it a great day.$

80/20 Ideabuilder®: Updated UI Overview (ver. 2.0.0)

80/20: 25 Series Anchor Fastener (25-3363)

80/20: 10 Series Access Hole Drill Jig (6120)

80/20: 570mm Task Light with High Low Switch (21057)

80/20: Roll-in T-nut with Ball Spring (3670)

8020 LLC (80/20) |

80/20: 10 Series 3-Hole Inside Corner Bracket (4176)