Tim McKay | 2 Different Wings 1 Airplane Test Flight @TimMcKay56 | Uploaded 3 years ago | Updated 1 hour ago
2 Different Wings 1 Airplane Test Flight
In this video I will do an experiment with using two different wings on the same airplane fuselage. This is a 5 ounce foam board flyer. The first wing is a flat, no airfoil, 3/16 inch foam board wing with 0.5 inch dihedral and a slight amount of positive incidence. The model airplane has three channels of control with rudder, elevator and throttle.
The second wing is an airfoil shape, same chord and dihedral. I use rubber bands to keep the wings in place.
Note that with the first iteration of this model, testing out a flat wing with zero dihedral, I used ailerons for roll control. For this version, with rudder control, I added a half inch of dihedral which seemed to work fine.
The plane few quite well with both wings. Interestingly enough, the flat wing seemed to handle a bit better. The model needed no trim and was smooth and responsive during the model airplane test flight. My conclusions are that a flat, no airfoil wing can fly just fine in a lighter weight model.
Lite Flyer 1 plans:
drive.google.com/drive/folders/1SReOZaSqptVoi0FOt0LhxP-oKCi5f3MG?usp=sharing
Here is a link to my YouTube Channel:
youtube.com/c/TimMcKay56
Many thanks in advance for a post of this video on Facebook, it truly helps the channel a lot!
Regards,
Tim
Airplane details:
All construction from 3/16" foam board and hot glue gun
Park 250 electric motor
7 X 3.5 propeller
Spektrum AR620 receiver
2 HS40 servos
2 cell lipo battery
Castle Talon 15 ESC
Chapters
00:00 - Intro
00:41 - Project overview
01:49 - RC electronics
02:35 - RC installation
03:38 - Building the wings
04:28 - Completed model
09:35 - Test flights
2 Different Wings 1 Airplane Test Flight
In this video I will do an experiment with using two different wings on the same airplane fuselage. This is a 5 ounce foam board flyer. The first wing is a flat, no airfoil, 3/16 inch foam board wing with 0.5 inch dihedral and a slight amount of positive incidence. The model airplane has three channels of control with rudder, elevator and throttle.
The second wing is an airfoil shape, same chord and dihedral. I use rubber bands to keep the wings in place.
Note that with the first iteration of this model, testing out a flat wing with zero dihedral, I used ailerons for roll control. For this version, with rudder control, I added a half inch of dihedral which seemed to work fine.
The plane few quite well with both wings. Interestingly enough, the flat wing seemed to handle a bit better. The model needed no trim and was smooth and responsive during the model airplane test flight. My conclusions are that a flat, no airfoil wing can fly just fine in a lighter weight model.
Lite Flyer 1 plans:
drive.google.com/drive/folders/1SReOZaSqptVoi0FOt0LhxP-oKCi5f3MG?usp=sharing
Here is a link to my YouTube Channel:
youtube.com/c/TimMcKay56
Many thanks in advance for a post of this video on Facebook, it truly helps the channel a lot!
Regards,
Tim
Airplane details:
All construction from 3/16" foam board and hot glue gun
Park 250 electric motor
7 X 3.5 propeller
Spektrum AR620 receiver
2 HS40 servos
2 cell lipo battery
Castle Talon 15 ESC
Chapters
00:00 - Intro
00:41 - Project overview
01:49 - RC electronics
02:35 - RC installation
03:38 - Building the wings
04:28 - Completed model
09:35 - Test flights