Uploaded October 2026 | Updated November 2026, 5 days ago
UVC lamps are widely used for sterilisation of well and tank water, and for sterilising surfaces.
Because the wavelength of the UVC light (254nm) is so short, it requires specialist ultra pure glass to pass the required wavelength.
The destructive nature of UVC light means that it damages its own glass tube over time, meaning that while it's still working internally, the actual UVC output may have dropped significantly. It's not something you can see directly as UVC is invisible, but the other wavelengths that give the tubes a ghostly blue glow still shine through the glass.
It is recommended that UVC tubes in continuous use are changed at least once a year.
Never look at a lit UVC tube without eye and skin protection. Even a short exposure will cause serious eye irritation (photokeratitis) in the same way as a welding arc does.
If exposed, you may wake up in the middle of the night feeling like your eyes are full of sand. Although very unpleasant, the eyes will recover over a day or two.
Note that this does not apply to 365nm UVA tubes as used for glowing art type applications or in insect attracting units.
UVC lamps are widely used for sterilisation of well and tank water, and for sterilising surfaces.
Because the wavelength of the UVC light (254nm) is so short, it requires specialist ultra pure glass to pass the required wavelength.
The destructive nature of UVC light means that it damages its own glass tube over time, meaning that while it's still working internally, the actual UVC output may have dropped significantly. It's not something you can see directly as UVC is invisible, but the other wavelengths that give the tubes a ghostly blue glow still shine through the glass.
It is recommended that UVC tubes in continuous use are changed at least once a year.
Never look at a lit UVC tube without eye and skin protection. Even a short exposure will cause serious eye irritation (photokeratitis) in the same way as a welding arc does.
If exposed, you may wake up in the middle of the night feeling like your eyes are full of sand. Although very unpleasant, the eyes will recover over a day or two.
Note that this does not apply to 365nm UVA tubes as used for glowing art type applications or in insect attracting units.
![Making a laser lumia/aura effects disk - with a slight silicone disaster
The Lumia or Aura effect is created by shining a laser through rippled glass, but it can be difficult to find the right glass, and someone who can cut a circle from it for you. This was an experiment to use a standard filament based 3D printer to create a silicone mould for optically clear resin.
This was my first attempt at creating a mould with liquid silicone. Apparently platinum-cured silicone is very fussy about what its used with, and my master shape was fine on its own, but when pre-textured with UV cured resin it prevented the silicone from curing in that area and caused an outgassing effect. Even with ordinary two-part resin the silicone still stayed slightly sticky where it was in contact.
In the end the answer was to use the 3D printed PLA mould on its own and add the effects onto the cast resin disks afterwards.
When using UV curing resin I strongly recommend wearing gloves to protect your hands from contact with it. The chemicals used to make it light sensitive can also make your skin sensitive to sunlight.
This is an experimental device. I dont know how the resin will hold up to specific wavelengths of laser energy. Its also probably limited to low power lasers for safety. The disk can also be used with various styles of LEDs for an aurora borealis effect.
For laser use the disk should rotate very slowly to get the best optical warping effects.
Heres the OpenSCAD script that creates your custom mould for this project.
There are two adjustable variables - one for the outer diameter of the disk and one for the central hub where it attaches to a suitable motor. The script will automatically place a small central indent for aligning a drill if needed.
OpenSCAD can be downloaded for Windows, Linux and Mac (plus others) from the official site:-
https://openscad.org/
To use the script, copy and paste it into the left hand editor window in openscad. You can either adjust the two variables directly in the script or you can enable the customizer that will open a window to do it.
If you want to use the customizer then you can open it from the window drop down menu.
To see the results of any changes quickly, press the cube-button with two arrows on it. To do the full build press the cube-button with the hourglass on it, and when it is complete, save the file by pressing the STL button.
That will save a design file that can be used in your choice of slicer for 3D printing.
The script is below:-
//Ripple disk mould maker
//Diameter of disk in mm
dia=75;
//Diameter of central hub in mm
hub=20;
difference(){
cylinder(h=12,d=dia+12);
translate([0,0,1])
cylinder(h=12,d=dia+10);
}
difference(){
union(){
cylinder(h=5,d=dia);
cylinder(h=7,d=hub);
}
//Central drilling indent
translate([0,0,5.5])
cylinder(h=2,d1=0,d2=3);
}
$fn=100; Making a laser lumia/aura effects disk - with a slight silicone disaster](https://i.ytimg.com/vi/5yNYqsbBkJM/mqdefault.jpg)








![The LED candle project that went wrong (twice)
This project was supposed to be so easy. But a decision to add over-discharge protection backfired when I discovered that when the little DW01 lithium cell protection modules are powered up, they sometimes go into standby mode and can only be woken by charge current going into the cell.
I hadnt broken the wire on the LED (until I pulled it!). The module had just gone into standby mode.
On a plus note, the candle now has a USB-C charge port inside it for recharging the lithium cell.
I like to show my failures so you dont feel so bad when your own project goes wrong.
AliExpress has loads of flickering LEDs in all colours, but Ive not been able to find packs of the newer style subtle version yet.
Here are the scripts for making the candle parts. You can copy and paste them into OpenSCAD to get custom 3D printing files.
The base:-
//Candle base
//Base thickness
base=1.5;
//Base diameter
basedia=50;
//Insert height
height=7;
difference(){
union(){
//base plate
translate([0,0,0])
cylinder(h=base,d=basedia);
//insert
translate([0,0,base])
cylinder(h=height,d=23);
//reinforcing taper
translate([0,0,base])
cylinder(h=2,d1=25,d2=23);
}
//inner core
translate([0,0,1.5])
cylinder(h=10,d=21);
}
$fn=100;
The shaft sections:-
//stackable Candle shaft
//Height of main body
height=50;
difference(){
union(){
//Main body
translate([0,0,0])
cylinder(h=height,d=25);
//taper
translate([0,0,height])
cylinder(h=3,d1=25,d2=23);
//insert
translate([0,0,height+3])
cylinder(h=6,d=23);
}
//core
//Main body
translate([0,0,0])
cylinder(h=height,d=23);
//taper
translate([0,0,height])
cylinder(h=3,d1=23,d2=21);
//insert
translate([0,0,height+3])
cylinder(h=6,d=21);
}
$fn=100;
The flat top:-
//Flat candle cap
difference(){
union(){
//body
translate([0,0,0])
cylinder(h=6,d=25);
}
//core
translate([0,0,1])
cylinder(h=10,d=23);
//wick slot
translate([-1,-.5,-1])
cube([15,1,10]);
}
$fn=100;
The pointed top:-
//Pointed candle cap
difference(){
union(){
//body
translate([0,0,0])
cylinder(h=6,d=25);
//cone
translate([0,0,6])
cylinder(h=15,d1=25,d2=0);
}
//core
translate([0,0,-1])
cylinder(h=7,d=23);
translate([0,0,6])
cylinder(h=14,d1=23,d2=0);
//wick hole
translate([0,0,17])
cylinder(h=7,d=1.5);
//slot
translate([0,-.5,-1])
cube([15,1,22]);
}
$fn=100;
If you enjoy my videos, you can treat me to coffee, cookies and gadgets by supporting the channel on Patreon. You also get early access to videos without adverts, bonus footage and regular quiet Patreon live streams.
https://www.patreon.com/bigclive
Alternatively, for a single coffee contribution you can use PayPal:-
https://www.paypal.com/paypalme/bigclive
#ElectronicsCreators The LED candle project that went wrong (twice)](https://i.ytimg.com/vi/7l--KgoTh50/mqdefault.jpg)
