The LED candle project that went wrong (twice) @bigclivedotcom
The LED candle project that went wrong (twice)  @bigclivedotcom
Uploaded October 2026 | Updated November 2026, 5 days ago
This project was supposed to be so easy. But a decision to add over-discharge protection backfired when I discovered that when the little DW01 lithium cell protection modules are powered up, they sometimes go into standby mode and can only be "woken" by charge current going into the cell.

I hadn't broken the wire on the LED (until I pulled it!). The module had just gone into standby mode.

On a plus note, the candle now has a USB-C charge port inside it for recharging the lithium cell.

I like to show my failures so you don't feel so bad when your own project goes wrong.

AliExpress has loads of flickering LEDs in all colours, but I've not been able to find packs of the newer style subtle version yet.

Here are the scripts for making the candle parts. You can copy and paste them into OpenSCAD to get custom 3D printing files.


The base:-


//Candle base
//Base thickness
base=1.5;
//Base diameter
basedia=50;
//Insert height
height=7;
difference(){
union(){
//base plate
translate([0,0,0])
cylinder(h=base,d=basedia);
//insert
translate([0,0,base])
cylinder(h=height,d=23);
//reinforcing taper
translate([0,0,base])
cylinder(h=2,d1=25,d2=23);
}
//inner core
translate([0,0,1.5])
cylinder(h=10,d=21);
}
$fn=100;



The shaft sections:-


//stackable Candle shaft
//Height of main body
height=50;
difference(){
union(){
//Main body
translate([0,0,0])
cylinder(h=height,d=25);
//taper
translate([0,0,height])
cylinder(h=3,d1=25,d2=23);
//insert
translate([0,0,height+3])
cylinder(h=6,d=23);
}
//core
//Main body
translate([0,0,0])
cylinder(h=height,d=23);
//taper
translate([0,0,height])
cylinder(h=3,d1=23,d2=21);
//insert
translate([0,0,height+3])
cylinder(h=6,d=21);
}
$fn=100;



The flat top:-


//Flat candle cap
difference(){
union(){
//body
translate([0,0,0])
cylinder(h=6,d=25);
}
//core
translate([0,0,1])
cylinder(h=10,d=23);
//wick slot
translate([-1,-.5,-1])
cube([15,1,10]);
}
$fn=100;



The pointed top:-


//Pointed candle cap
difference(){
union(){
//body
translate([0,0,0])
cylinder(h=6,d=25);
//cone
translate([0,0,6])
cylinder(h=15,d1=25,d2=0);
}
//core
translate([0,0,-1])
cylinder(h=7,d=23);
translate([0,0,6])
cylinder(h=14,d1=23,d2=0);
//wick hole
translate([0,0,17])
cylinder(h=7,d=1.5);
//slot
translate([0,-.5,-1])
cube([15,1,22]);
}
$fn=100;




If you enjoy my videos, you can treat me to coffee, cookies and gadgets by supporting the channel on Patreon. You also get early access to videos without adverts, bonus footage and regular quiet Patreon live streams.

patreon.com/bigclive

Alternatively, for a single coffee contribution you can use PayPal:-
paypal.com/paypalme/bigclive

#ElectronicsCreators
The LED candle project that went wrong (twice)Muscle-wire cabinet lockInside an expensive TCP high efficiency light bulb from ASDAAliExpress unbagging joy - Digital controllers, thermostats, a pump, LEDs and moreHow to use a stepper motor driver for simple continuous rotation controlInside a cheap but impressive laser cubeStory time - and building one of my own PCBs (minor rant)Destructively testing thermal fusesReactivating an 1800s Victorian Leclanché cellHolographic fly repeller FLICKER ALERT!AliExpress unbagging joy - arson-cat, USB meter, PCB switchesCheap LED PAR can test and teardown
bigclivedotcom |

The LED candle project that went wrong (twice)

SHARE TO X SHARE TO REDDIT SHARE TO FACEBOOK WALLPAPER