Uploaded May 2026 | Updated November 2026, 5 days ago
Note that this experiment was done with carbon dioxide which produces much coarser bubbles than nitrogen. The finer nitrogen bubbles would diffuse throughout the liquid better.
This video is a follow up to the video about the Guinness widget that causes nucleation of nitrogen in the draught cans. Several people commented about emulating it in a clear container with a carbonator.
The widget is a hollow plastic ball moulded with a weight bias so that one side points down when floating in liquid. That side also has a tiny hole that points out at an angle.
When the can is sealed during manufacture, the internal pressure compresses some of the nitrated guinness into the sphere, and when the can is opened the pressure is suddenly released and it causes the sphere to blow out a stream of the nitrogenated guinness. That results in mass nucleation and diffusion of tiny nitrogen bubbles throughout the liquid.
Now I just have to work out how to get the widget back out of the carbonation bottle. It was a friction fit through the neck, and pushing it in was easier than getting it back out. I may have to fill the bottle with water and melt a hole in the top of the widget to hook it out.
If you enjoy my videos, supporting the channel on Patreon helps keep it independent of YouTube's quirks, avoids intrusive mid-video adverts, gives early access, bonus footage and regular quiet Patreon live streams.
patreon.com/bigclive
Alternatively, for a single coffee contribution you can use PayPal:-
paypal.com/paypalme/bigclive
#ElectronicsCreators
Note that this experiment was done with carbon dioxide which produces much coarser bubbles than nitrogen. The finer nitrogen bubbles would diffuse throughout the liquid better.
This video is a follow up to the video about the Guinness widget that causes nucleation of nitrogen in the draught cans. Several people commented about emulating it in a clear container with a carbonator.
The widget is a hollow plastic ball moulded with a weight bias so that one side points down when floating in liquid. That side also has a tiny hole that points out at an angle.
When the can is sealed during manufacture, the internal pressure compresses some of the nitrated guinness into the sphere, and when the can is opened the pressure is suddenly released and it causes the sphere to blow out a stream of the nitrogenated guinness. That results in mass nucleation and diffusion of tiny nitrogen bubbles throughout the liquid.
Now I just have to work out how to get the widget back out of the carbonation bottle. It was a friction fit through the neck, and pushing it in was easier than getting it back out. I may have to fill the bottle with water and melt a hole in the top of the widget to hook it out.
If you enjoy my videos, supporting the channel on Patreon helps keep it independent of YouTube's quirks, avoids intrusive mid-video adverts, gives early access, bonus footage and regular quiet Patreon live streams.
patreon.com/bigclive
Alternatively, for a single coffee contribution you can use PayPal:-
paypal.com/paypalme/bigclive
#ElectronicsCreators
![The LED candle project that went wrong (twice)
This project was supposed to be so easy. But a decision to add over-discharge protection backfired when I discovered that when the little DW01 lithium cell protection modules are powered up, they sometimes go into standby mode and can only be woken by charge current going into the cell.
I hadnt broken the wire on the LED (until I pulled it!). The module had just gone into standby mode.
On a plus note, the candle now has a USB-C charge port inside it for recharging the lithium cell.
I like to show my failures so you dont feel so bad when your own project goes wrong.
AliExpress has loads of flickering LEDs in all colours, but Ive not been able to find packs of the newer style subtle version yet.
Here are the scripts for making the candle parts. You can copy and paste them into OpenSCAD to get custom 3D printing files.
The base:-
//Candle base
//Base thickness
base=1.5;
//Base diameter
basedia=50;
//Insert height
height=7;
difference(){
union(){
//base plate
translate([0,0,0])
cylinder(h=base,d=basedia);
//insert
translate([0,0,base])
cylinder(h=height,d=23);
//reinforcing taper
translate([0,0,base])
cylinder(h=2,d1=25,d2=23);
}
//inner core
translate([0,0,1.5])
cylinder(h=10,d=21);
}
$fn=100;
The shaft sections:-
//stackable Candle shaft
//Height of main body
height=50;
difference(){
union(){
//Main body
translate([0,0,0])
cylinder(h=height,d=25);
//taper
translate([0,0,height])
cylinder(h=3,d1=25,d2=23);
//insert
translate([0,0,height+3])
cylinder(h=6,d=23);
}
//core
//Main body
translate([0,0,0])
cylinder(h=height,d=23);
//taper
translate([0,0,height])
cylinder(h=3,d1=23,d2=21);
//insert
translate([0,0,height+3])
cylinder(h=6,d=21);
}
$fn=100;
The flat top:-
//Flat candle cap
difference(){
union(){
//body
translate([0,0,0])
cylinder(h=6,d=25);
}
//core
translate([0,0,1])
cylinder(h=10,d=23);
//wick slot
translate([-1,-.5,-1])
cube([15,1,10]);
}
$fn=100;
The pointed top:-
//Pointed candle cap
difference(){
union(){
//body
translate([0,0,0])
cylinder(h=6,d=25);
//cone
translate([0,0,6])
cylinder(h=15,d1=25,d2=0);
}
//core
translate([0,0,-1])
cylinder(h=7,d=23);
translate([0,0,6])
cylinder(h=14,d1=23,d2=0);
//wick hole
translate([0,0,17])
cylinder(h=7,d=1.5);
//slot
translate([0,-.5,-1])
cube([15,1,22]);
}
$fn=100;
If you enjoy my videos, you can treat me to coffee, cookies and gadgets by supporting the channel on Patreon. You also get early access to videos without adverts, bonus footage and regular quiet Patreon live streams.
https://www.patreon.com/bigclive
Alternatively, for a single coffee contribution you can use PayPal:-
https://www.paypal.com/paypalme/bigclive
#ElectronicsCreators The LED candle project that went wrong (twice)](https://i.ytimg.com/vi/7l--KgoTh50/mqdefault.jpg)









