Uploaded September 2025 | Updated November 2026, 19 hours ago
The Chevelle FINALLY Leaves the Starting Line Like a Real Hotrod!
We’ve been slowly dialing in Paige’s 1964 Chevy Chevelle from back to front, turning it into a proper street/strip hotrod. In the last video (link below), we swapped out the master cylinder, booster, and proportioning valve to finally fix the weak brake pressure issue. With that sorted, Paige was able to bring the car up on the converter at the starting line for the first time—and it completely changed the game.
The surprise? The Chevelle now hits the tire hard enough to spin right out of the hole! What used to dead-hook now breaks loose, but Paige adapted fast and started learning how to drive with the extra power at launch. By the end of the night, she set a new personal best and even outran a friend’s car (his Dragy confirmed the Chevelle was flying!).
This was the first time the car really left like a hotrod—and it showed us what this combo is capable of. Stick around, because we’re only scratching the surface of what’s possible with this build.
📺 Previous Episode:
New Power Disk Master / Booster / Prop Valve - No More Stopping Like A School Bus
🔗 youtu.be/M3o22FNd70c 🔗
🔔 Subscribe so you don’t miss the next step in the Chevelle’s journey!
Hashtags / SEO Tags:
#Chevelle #MuscleCar #DragRacing #StreetCar #ChevyChevelle #HotRod #QuarterMile #BracketRacing #DragStrip #PerformanceBuild #CarChannel #ProjectCar
The Chevelle FINALLY Leaves the Starting Line Like a Real Hotrod!
We’ve been slowly dialing in Paige’s 1964 Chevy Chevelle from back to front, turning it into a proper street/strip hotrod. In the last video (link below), we swapped out the master cylinder, booster, and proportioning valve to finally fix the weak brake pressure issue. With that sorted, Paige was able to bring the car up on the converter at the starting line for the first time—and it completely changed the game.
The surprise? The Chevelle now hits the tire hard enough to spin right out of the hole! What used to dead-hook now breaks loose, but Paige adapted fast and started learning how to drive with the extra power at launch. By the end of the night, she set a new personal best and even outran a friend’s car (his Dragy confirmed the Chevelle was flying!).
This was the first time the car really left like a hotrod—and it showed us what this combo is capable of. Stick around, because we’re only scratching the surface of what’s possible with this build.
📺 Previous Episode:
New Power Disk Master / Booster / Prop Valve - No More Stopping Like A School Bus
🔗 youtu.be/M3o22FNd70c 🔗
🔔 Subscribe so you don’t miss the next step in the Chevelle’s journey!
Hashtags / SEO Tags:
#Chevelle #MuscleCar #DragRacing #StreetCar #ChevyChevelle #HotRod #QuarterMile #BracketRacing #DragStrip #PerformanceBuild #CarChannel #ProjectCar









![Risking a Wiped Cam to Wake Up This Scrapyard 454 Big Block
We risked wiping a cam to wake up Paiges 454 Big Block Chevelle just 5 WEEKS before Rocky Mountain Race Week 2.0!
The budget plan was simple: bolt on a set of ZZ502 GM Performance Oval Port Aluminum heads and stuff a Comp Cams XE274H hydraulic flat tappet cam (11-246-3) in this scrapyard pulled 454 BBC to spice it up for drag-and-drive. It blew up fast - after consulting Brand Racing Engines, there was no good way to get the valve spring installed height right on our ZZ502 heads for the flat tappet cam, the spring install height on the heads just wont work and no time to figure out other parts and were no where near well off enough to get custom order parts.
So we called an audible: out with the aluminum heads, in with a set of old-school 781 casting iron heads. Not as good on paper, but a massive upgrade over the awful peanut port heads on the motor, and they work with the parts we already had.
Tear down revealed this dirt-scrapyard 454 was actually loaded - 30 over Speed Pro pistons, double roller timing set, Melling M77HV oil pump, all looking brand new (total score of a $500 marketplace find). We cleaned everything up, loaded the XE274H with Comp DLC lifters and Clevite Cam Guard, packed the 781s with PAC Racing Springs, sealed them with Felpro 8180-PT2 head gaskets, and took it to BradFabs run stand for final assembly and break-in.
Then the longest 20 minutes in hot rodding: flat tappet break-in straight to 2000+ RPM, no red flags, cool down overnight, check the valvetrain, and fire it one more time to hear that new cam chop. Now its time to stuff Paiges refreshed big block back in her 64 Chevelle and get ready for Race Week. . . at least thats the plan!
Paiges 1964 Chevelle - 454 Big Block Chevy / 4L80E swap / drag-and-drive build playlist linked above.
#chevelle #chevy454 #bigblockchevy #enginerebuild #hotrod
CHAPTERS:
00:00 5 Weeks to Race Week - The Plan to Spice Up the 454
02:15 Why the ZZ502 Aluminum Heads FAILED With This Cam
04:30 The Audible: 781 Iron Heads vs Peanut Ports
06:45 Teardown Surprise - Scrapyard 454 Has Good Parts
09:10 Cam Install: XE274H + DLC Lifters + Cam Guard
11:30 Building the 781s + Felpro Head Gaskets
14:00 On BradFabs Run Stand - Assembly Complete
16:15 The Dreaded 20-Minute Flat Tappet Break-In
19:30 Next Morning Inspection - Did We Wipe A Lobe?
21:30 That New Cam Sound + Packing For Home
23:00 Next Up: Back In The Chevelle For RMRW 2.0
Affiliate links & shop staples I actually use:
[PUT YOUR TOP 2-3 LINKS HERE - per your rule, high-value links stay near the top]
Primeweld TIG225X TIG / YesWelder MIG205-DS Pro MIG - what we weld with in the shop
Super Clean - garage cleanup process [if applicable to this video]
Follow the Chevelle / Nova Wagon / Trailer builds - new long-form every week at 9:01am CT. Risking a Wiped Cam to Wake Up This Scrapyard 454 Big Block](https://i.ytimg.com/vi/AjUaismKxrY/mqdefault.jpg)
