Uploaded September 2025 | Updated November 2026, 15 hours ago
700R4 TV cables can be tricky to dial in—especially in tight engine bays like a Chevy II. After the first successful outing with our ’65 Nova Wagon at King of the Open Road, we’re back in the shop fixing up a few things we discovered on the maiden adventure.
One big issue: no full throttle! That’s just not acceptable when you’ve got a dirty old 327ci small block Chevy built with classic ‘60s parts. To let this little mouse motor sing, I rebuilt the TV cable bracket with a compact, low-profile setup. This improves throttle linkage geometry, gives the clearance needed, and finally allows the 650cfm double pumper to open up to true wide-open throttle.
Join me in the garage as we chase down throttle response, rebuild the TV cable system, and get this Chevy II dialed in for more fun.
✔ Don’t forget to check out the Wypall ProScrub Wipes—they’ve been a game changer in the shop:
🔗 amzn.to/4g1ErdV
Disclaimer: As an Amazon Associate I earn from qualifying purchases. This means I may earn a small commission at no extra cost to you.
#ChevyII #NovaWagon #700R4 #SmallBlockChevy #MuscleCar #CarRestoration #EngineBay #HotRod #GarageBuild #ClassicCars #CarProjects #WideOpenThrottle #ChevyNova #CarFix #ThrottleResponse #MuscleCarMadness #StreetMachine #TVcable #DIYCarRepair #OldSchoolChevy
700R4 TV cables can be tricky to dial in—especially in tight engine bays like a Chevy II. After the first successful outing with our ’65 Nova Wagon at King of the Open Road, we’re back in the shop fixing up a few things we discovered on the maiden adventure.
One big issue: no full throttle! That’s just not acceptable when you’ve got a dirty old 327ci small block Chevy built with classic ‘60s parts. To let this little mouse motor sing, I rebuilt the TV cable bracket with a compact, low-profile setup. This improves throttle linkage geometry, gives the clearance needed, and finally allows the 650cfm double pumper to open up to true wide-open throttle.
Join me in the garage as we chase down throttle response, rebuild the TV cable system, and get this Chevy II dialed in for more fun.
✔ Don’t forget to check out the Wypall ProScrub Wipes—they’ve been a game changer in the shop:
🔗 amzn.to/4g1ErdV
Disclaimer: As an Amazon Associate I earn from qualifying purchases. This means I may earn a small commission at no extra cost to you.
#ChevyII #NovaWagon #700R4 #SmallBlockChevy #MuscleCar #CarRestoration #EngineBay #HotRod #GarageBuild #ClassicCars #CarProjects #WideOpenThrottle #ChevyNova #CarFix #ThrottleResponse #MuscleCarMadness #StreetMachine #TVcable #DIYCarRepair #OldSchoolChevy





![Risking a Wiped Cam to Wake Up This Scrapyard 454 Big Block
We risked wiping a cam to wake up Paiges 454 Big Block Chevelle just 5 WEEKS before Rocky Mountain Race Week 2.0!
The budget plan was simple: bolt on a set of ZZ502 GM Performance Oval Port Aluminum heads and stuff a Comp Cams XE274H hydraulic flat tappet cam (11-246-3) in this scrapyard pulled 454 BBC to spice it up for drag-and-drive. It blew up fast - after consulting Brand Racing Engines, there was no good way to get the valve spring installed height right on our ZZ502 heads for the flat tappet cam, the spring install height on the heads just wont work and no time to figure out other parts and were no where near well off enough to get custom order parts.
So we called an audible: out with the aluminum heads, in with a set of old-school 781 casting iron heads. Not as good on paper, but a massive upgrade over the awful peanut port heads on the motor, and they work with the parts we already had.
Tear down revealed this dirt-scrapyard 454 was actually loaded - 30 over Speed Pro pistons, double roller timing set, Melling M77HV oil pump, all looking brand new (total score of a $500 marketplace find). We cleaned everything up, loaded the XE274H with Comp DLC lifters and Clevite Cam Guard, packed the 781s with PAC Racing Springs, sealed them with Felpro 8180-PT2 head gaskets, and took it to BradFabs run stand for final assembly and break-in.
Then the longest 20 minutes in hot rodding: flat tappet break-in straight to 2000+ RPM, no red flags, cool down overnight, check the valvetrain, and fire it one more time to hear that new cam chop. Now its time to stuff Paiges refreshed big block back in her 64 Chevelle and get ready for Race Week. . . at least thats the plan!
Paiges 1964 Chevelle - 454 Big Block Chevy / 4L80E swap / drag-and-drive build playlist linked above.
#chevelle #chevy454 #bigblockchevy #enginerebuild #hotrod
CHAPTERS:
00:00 5 Weeks to Race Week - The Plan to Spice Up the 454
02:15 Why the ZZ502 Aluminum Heads FAILED With This Cam
04:30 The Audible: 781 Iron Heads vs Peanut Ports
06:45 Teardown Surprise - Scrapyard 454 Has Good Parts
09:10 Cam Install: XE274H + DLC Lifters + Cam Guard
11:30 Building the 781s + Felpro Head Gaskets
14:00 On BradFabs Run Stand - Assembly Complete
16:15 The Dreaded 20-Minute Flat Tappet Break-In
19:30 Next Morning Inspection - Did We Wipe A Lobe?
21:30 That New Cam Sound + Packing For Home
23:00 Next Up: Back In The Chevelle For RMRW 2.0
Affiliate links & shop staples I actually use:
[PUT YOUR TOP 2-3 LINKS HERE - per your rule, high-value links stay near the top]
Primeweld TIG225X TIG / YesWelder MIG205-DS Pro MIG - what we weld with in the shop
Super Clean - garage cleanup process [if applicable to this video]
Follow the Chevelle / Nova Wagon / Trailer builds - new long-form every week at 9:01am CT. Risking a Wiped Cam to Wake Up This Scrapyard 454 Big Block](https://i.ytimg.com/vi/AjUaismKxrY/mqdefault.jpg)




