Tormach Inc. | Tormach 1300PL Plasma Table Installation Video @tormachinc | Uploaded August 2020 | Updated October 2024, 2 hours ago.
The 1300PL Plasma Table was designed to be easily delivered and installed by the customer. It arrives on a pallet, so no forklift is necessary, just a couple 4 x 4's and an engine hoist to remove it from the pallet and tip it down to the ground. We estimate that it will take approximately two hours to setup and start running.
To help our customers, Tormach supplies an Owner's Manual that goes through all the steps of setting up and running the Tormach 1300PL Plasma Table. In addition, we also provide installation videos to supplement the Owner's Manual.
Chapter Links for the Video:
0:00 Introduction
0:28 Operator Manual
0:45 Moving the Crate
1:16 Unpack the Crate
1:52 Remove Frame from the Crate
4:05 Lowering the Table to its Feet
4:45 Install the Rear Legs
5:17 Level the Machine Frame
7:10 Install the Side Panel and Cable Carriers
9:03 Install the Plasma Torch and Lead
13:14 Install Machine Arm and Controller
15:03 Install the Slats and Fill the Water Table
15:58 Verify the Installation
18:42 Testing the Plasma Source Control
19:15 Test Torch Breakaway
19:38 Test the Ohmic Probing
21:58 Setup the PathPilot Controller
Please download the 1300PL Plasma Table Owner's Manual here: tormach.com/docs/download/assetlink/asset_id/609
P.S.: Never run your water table with any pets in the vicinity of the plasma torch.
Interested in a Tormach machine? Schedule a call with one of our team members at hubs.ly/Q029gf-H0 and they will be happy to answer any questions you have.
Be sure to subscribe for updates on everything Tormach: goo.gl/sWeCs7
Join the Tormach Forums here: hubs.ly/Q029ggRV0
There are several ways to contact Tormach Technical Support.
If you want technical support, please follow these instructions to open a support ticket: hubs.ly/Q029ghcD0
Tormach Technical Support page: hubs.ly/Q029ghwW0
Tormach Technical Support contact: tormach.atlassian.net/servicedesk/customer/portals
About Us: At Tormach, we're dedicated to providing exceptionally engineered products, technical support, and customer service at the lowest possible cost. Our focus is to help you realize your CNC goals through tools and resources that transform your concepts into real products. Connect with us:
Visit our website: hubs.ly/Q029gj8M0
Facebook: facebook.com/tormach
Instagram: instagram.com/tormach
Twitter: twitter.com/tormach
LinkedIn: linkedin.com/company/tormach
The 1300PL Plasma Table was designed to be easily delivered and installed by the customer. It arrives on a pallet, so no forklift is necessary, just a couple 4 x 4's and an engine hoist to remove it from the pallet and tip it down to the ground. We estimate that it will take approximately two hours to setup and start running.
To help our customers, Tormach supplies an Owner's Manual that goes through all the steps of setting up and running the Tormach 1300PL Plasma Table. In addition, we also provide installation videos to supplement the Owner's Manual.
Chapter Links for the Video:
0:00 Introduction
0:28 Operator Manual
0:45 Moving the Crate
1:16 Unpack the Crate
1:52 Remove Frame from the Crate
4:05 Lowering the Table to its Feet
4:45 Install the Rear Legs
5:17 Level the Machine Frame
7:10 Install the Side Panel and Cable Carriers
9:03 Install the Plasma Torch and Lead
13:14 Install Machine Arm and Controller
15:03 Install the Slats and Fill the Water Table
15:58 Verify the Installation
18:42 Testing the Plasma Source Control
19:15 Test Torch Breakaway
19:38 Test the Ohmic Probing
21:58 Setup the PathPilot Controller
Please download the 1300PL Plasma Table Owner's Manual here: tormach.com/docs/download/assetlink/asset_id/609
P.S.: Never run your water table with any pets in the vicinity of the plasma torch.
Interested in a Tormach machine? Schedule a call with one of our team members at hubs.ly/Q029gf-H0 and they will be happy to answer any questions you have.
Be sure to subscribe for updates on everything Tormach: goo.gl/sWeCs7
Join the Tormach Forums here: hubs.ly/Q029ggRV0
There are several ways to contact Tormach Technical Support.
If you want technical support, please follow these instructions to open a support ticket: hubs.ly/Q029ghcD0
Tormach Technical Support page: hubs.ly/Q029ghwW0
Tormach Technical Support contact: tormach.atlassian.net/servicedesk/customer/portals
About Us: At Tormach, we're dedicated to providing exceptionally engineered products, technical support, and customer service at the lowest possible cost. Our focus is to help you realize your CNC goals through tools and resources that transform your concepts into real products. Connect with us:
Visit our website: hubs.ly/Q029gj8M0
Facebook: facebook.com/tormach
Instagram: instagram.com/tormach
Twitter: twitter.com/tormach
LinkedIn: linkedin.com/company/tormach