Uploaded March 2021 | Updated September 2026, 1 week ago
In this video I'll take you through my print settings for this super matte PLA filament from D3D and Digitmakers.ca. This is a high quality, premium PLA filament with a very low sheen that will give you a similar look to nylon carbon fiber filaments with the low cost and ease of printing of regular PLA. It also comes in a variety of colors and is conveniently packaged in resealable bags.
You can find the filament here:
► digitmakers.ca/products/d3d-premium-matte-pla-filament-1-75mm-1kg-spool?variant=12272351117348
All of the models were printed on an ANET ET5X printer with zero modifications. No special equipment or upgrades necessary to print this filament. Just keep the print speeds low and you should get great results!
If you're looking for the models printed in this video, check out these links:
► thingiverse.com/thing:2999036
► thingiverse.com/thing:4660786
► thingiverse.com/thing:3743939
► thingiverse.com/thing:4591435
Big thank you to Digitmakers.ca who provided me with the two rolls of matte PLA as seen in the video. Full disclosure I was not compensated in any other way for the making of this video. I highly recommend this filament and it is my honest opinion that you will like it!
Hope this video helps you guys and if you have any questions, feel free to ask them in the comments section below!
Thanks for watching!
#DIY #3DPRINTING #FILAMENT
****************************************************************
If you enjoy and have benefited from my content and are feeling generous I would love your support! You can "buy me a coffee" here:
► paypal.com/donate/?hosted_button_id=V2T6MEFUGP73Y ☕
By supporting my channel you are encouraging me to continue with this time consuming endeavor. A lot of time goes into design work, building my projects, filming the videos, editing the videos, etc. Plus it all costs money! Your generosity goes a long way in helping me bring you better content as often as I can!
Follow me on Instagram!
► instagram.com/embraceracing 📷
If you liked this video, perhaps you will also enjoy some channels that I personally find inspiring and interesting...
DIY and MAKER:
► The Hacksmith
youtube.com/channel/UCjgpFI5dU-D1-kh9H1muoxQ
► Adam Savage Tested
youtube.com/channel/UCiDJtJKMICpb9B1qf7qjEOA
► Thomas Sanladerer
youtube.com/user/ThomasSanladerer
Car Content:
► Mighty Car Mods
youtube.com/channel/UCgJRL30YS6XFxq9Ga8W2J3A
► Drivetribe
youtube.com/channel/UChiwLDIBJrV5SxqdixMHm
In this video I'll take you through my print settings for this super matte PLA filament from D3D and Digitmakers.ca. This is a high quality, premium PLA filament with a very low sheen that will give you a similar look to nylon carbon fiber filaments with the low cost and ease of printing of regular PLA. It also comes in a variety of colors and is conveniently packaged in resealable bags.
You can find the filament here:
► digitmakers.ca/products/d3d-premium-matte-pla-filament-1-75mm-1kg-spool?variant=12272351117348
All of the models were printed on an ANET ET5X printer with zero modifications. No special equipment or upgrades necessary to print this filament. Just keep the print speeds low and you should get great results!
If you're looking for the models printed in this video, check out these links:
► thingiverse.com/thing:2999036
► thingiverse.com/thing:4660786
► thingiverse.com/thing:3743939
► thingiverse.com/thing:4591435
Big thank you to Digitmakers.ca who provided me with the two rolls of matte PLA as seen in the video. Full disclosure I was not compensated in any other way for the making of this video. I highly recommend this filament and it is my honest opinion that you will like it!
Hope this video helps you guys and if you have any questions, feel free to ask them in the comments section below!
Thanks for watching!
#DIY #3DPRINTING #FILAMENT
****************************************************************
If you enjoy and have benefited from my content and are feeling generous I would love your support! You can "buy me a coffee" here:
► paypal.com/donate/?hosted_button_id=V2T6MEFUGP73Y ☕
By supporting my channel you are encouraging me to continue with this time consuming endeavor. A lot of time goes into design work, building my projects, filming the videos, editing the videos, etc. Plus it all costs money! Your generosity goes a long way in helping me bring you better content as often as I can!
Follow me on Instagram!
► instagram.com/embraceracing 📷
If you liked this video, perhaps you will also enjoy some channels that I personally find inspiring and interesting...
DIY and MAKER:
► The Hacksmith
youtube.com/channel/UCjgpFI5dU-D1-kh9H1muoxQ
► Adam Savage Tested
youtube.com/channel/UCiDJtJKMICpb9B1qf7qjEOA
► Thomas Sanladerer
youtube.com/user/ThomasSanladerer
Car Content:
► Mighty Car Mods
youtube.com/channel/UCgJRL30YS6XFxq9Ga8W2J3A
► Drivetribe
youtube.com/channel/UChiwLDIBJrV5SxqdixMHm
