🔨 SUPER CLEAN your Shop-Vac Filter with this Simple and Cheap @NeedItMakeIt

Updated September 2026, 8 hours ago

🔨 SUPER CLEAN your Shop-Vac Filter with this Simple and Cheap

2 Simple Ways to Make Stronger 3D Prints + an Experimental Way

SLOW MY FAST PRINTER? #creality3dprinter #3dprinter #bambu

$Let Your Creality K1 MAX and K1 Printers Soak for the Best First Layers This is really easy to do, and now you dont need to think to get better results. Help support this channel! https://www.patreon.com/Needitmakeit Youre not along if youre having trouble getting a good first layer on your K1 or K1 Max printer. With the Max, we found out that with such a fast heating cycle, and the larger and thin bed were getting a lot of warpage, but we also found that the warpage didnt stop right away, the bed changed shape and then began to change back. Most of the settling back happened within 10 minutes but it continued for as long as 20 minutes. In this video I wanted to show you a way to pre-heat automatically so that you dont need to think about it. **Special note: The Max takes only 5 minutes to reach 100C, its far faster than most other printers, adding a bit of time back to this heating cycle is a good idea and will give you the best results with the thickness of aluminum plate were dealing with. Another way to support this channel indirectly is through my Amazon affiliate links (where I receive a small commission). It helps me to continue to provide high-quality content videos. Thank you for your support! NEW MIC (I bought this) https://amzn.to/3vcMKAr - Rode Wireless ME mic (Saved me about 4+ hours/vid) https://amzn.to/3NBFvZe - Mag clip (Super handy, but a little pricy) BAMBU PRINTERS https://shrsl.com/4aghz CREALITY PRINTERS https://shrsl.com/4aghy CREALITY HYPER PLA https://shrsl.com/4aghn Here is the info you need to copy and paste (Starting with M190 of course) These are all for 9 minutes, I will work towards a follow up video to set a variable time... I dont know how to do this yet. ***WE HAVE AN UPDATE (Originals are first, we also have auto-time adjust below) Thanks to @stew675 for this very elegant solution ORCA(Original)🐋 M190 S[bed_temperature_initial_layer_single] G4 P540000 ORCA(Auto-time)🐋 M190 S[bed_temperature_initial_layer_single] G4 P{max(0, first_layer_bed_temperature[0] -10) * 6000} CREALITY PRINT(Original)🟦 M190 S[material_bed_temperature_layer_0] G4 P540000 CREALITY PRINT(Auto-time)🟦 M190 S[material_bed_temperature_layer_0] G4 P{max(0, first_layer_bed_temperature[0] -10) * 6000} PRUSA SLICER(Original)🟠 M190 S[first_layer_bed_temperature] G4 P540000 PRUSA SLICER(Auto-time)🟠 M190 S[first_layer_bed_temperature] G4 P{max(0, first_layer_bed_temperature[0] -10) * 6000} #creality #crealityk1 #3dprinting$

My Prusa MK4S COLD SPOTS were bad, so I fixed them! Now the MK4S has the most even heat

Printer VS Printer - Creality K1 faces off against the Bambu X1C at HIGH SPEED - Who Wins?

Your Bambu H2D needs one of these to unleash its FULL POTENTIAL

Strong 3D Printed Connections on BIG parts

The next generation of 3D printers is coming, but Im not buying one unless it does these two steps

DEEP engrave every stone with the exact same settings using my MOPA fiber laser - SHORT

The Ultimate 3D printable tabletop gaming organization system

$Simple Ways to Make Stronger 3D Prints NUMBER TWO What happens when you do real drop tests on 3d prints? Do they bend, do they break, do they shatter? In this video well find out by testing different materials and designs at several DROP heights. Help support this channel! https://www.patreon.com/Needitmakeit I see a lot of testing videos, some of them are useful to compare materials against each other, but theyre not as useful when you want to apply them to real designs. If we want to protect something, should we use ABS? How about PETG? Or Maybe youre the PC type. I have an okay sense about each of the materials, but I couldnt tell you which material was best to protect expensive equipment, and which material could take continued abuse and not just break after one drop. This video is dedicated to doing realistic dop testing to see if we can get some real answers to those questions so we have a better idea of how to design 3d printed parts, and that we also have a sense about which materials perform the best under which conditions. In the previous video, we tested only PETG, it has a good reputation for being flexible, but it also has this other very strange property of becoming brittle and fracturing at a certain point. In this video were going to see if we can figure out the right mix of flex and strength for that material so we can use it and have the confidence that itll do the job. Which material do you think will perform the best? Check out the video for all of the details, it was a lot of fun, and I learned quite a bit. Lets just say that it isnt all about the size, there is more to it than that. Another way to support this channel indirectly is through my affiliate links (where I receive a small commission). It helps me to continue to provide high-quality content videos. Thank you for your support! NEW MIC (I bought this) https://amzn.to/3vcMKAr - Rode Wireless ME mic (Saved me about 4+ hours/vid) https://amzn.to/3NBFvZe - Mag clip (Super handy, but a little pricy) BAMBU PRINTERS https://shrsl.com/4aghz CREALITY PRINTERS https://shrsl.com/4aghy CREALITY HYPER PLA https://shrsl.com/4aghn Original Design: https://www.thingiverse.com/thing:4757295 #bambu #crealityk1 #3dprinting$