Uploaded October 2026 | Updated November 2026, 6 hours ago
SRF05, CH32V003, Lithium Battery Charger, Voltage Booster, into a Portable Ultrasonic Range Finder
======================================
Altium Develop (Free Legal License): altium.com/yt/MyVanitar
======================================
Schematic/PCB/Code: 365.altium.com/files/FD664D42-E3B2-4DDA-B0C9-AFDF5470A746
======================================
Other Videos: bit.ly/2N9OlPa
======================================
@AtiumOfficial
#altiumstories
Almost all ultrasonic range finders online use that damn Arduino board. Arduino is a demo board; it's not cost-effective or suitable for a final or commercial design.
In this project, I used a cheap CH32V003J4 8-Pin MCU, an SRF05 module, an SSD1306 I2C 0.96-inch OLED module, a lithium battery charger circuit, and a boost converter circuit to build a fully portable design.
You can carry this board anywhere you like and use a conventional USB-C mobile charger to charge its battery.
SRF05, CH32V003, Lithium Battery Charger, Voltage Booster, into a Portable Ultrasonic Range Finder
======================================
Altium Develop (Free Legal License): altium.com/yt/MyVanitar
======================================
Schematic/PCB/Code: 365.altium.com/files/FD664D42-E3B2-4DDA-B0C9-AFDF5470A746
======================================
Other Videos: bit.ly/2N9OlPa
======================================
@AtiumOfficial
#altiumstories
Almost all ultrasonic range finders online use that damn Arduino board. Arduino is a demo board; it's not cost-effective or suitable for a final or commercial design.
In this project, I used a cheap CH32V003J4 8-Pin MCU, an SRF05 module, an SSD1306 I2C 0.96-inch OLED module, a lithium battery charger circuit, and a boost converter circuit to build a fully portable design.
You can carry this board anywhere you like and use a conventional USB-C mobile charger to charge its battery.


![12V-7A AC to DC Switching Power Supply [SMPS]
12V-7A AC to DC Flyback Switching Power Supply [SMPS]
Article: https://www.powerelectronicsnews.com/12v-7a-ac-to-dc-flyback-switching-power-supply/
Altium Designer + Legal License (Free): https://www.altium.com/yt/myvanitar
Altium 365: https://www.altium.com/altium-365
OctoPart: https://octopart.com
Other Videos: http://bit.ly/2N9OlPa
The most essential part of any electronic device is the power supply unit. Any instability or malfunction in this part causes the device to stop its duty or show weird behavior. In this article/video, I introduced an AC-to-DC flyback switching power supply that converts 180V-260VAC to 12VDC, which can be used in a variety of applications.
The maximum power delivery of this power supply is 84W, which means it can handle 7A continuously at 12V output. The transformer can deliver higher currents, however, the educational purpose (hand winding of the transformer) and thermal stress on the switching controller were considered (the peak current of the controllerās MOSFET is around 2.3A, at 7A). The controller chip is KA1M0565, which operates using a 470K startup resistor and a small auxiliary winding on the transformer. The transformers ferrite core is ER28-17-11, and the switching frequency is 67KHz. A potentiometer allows the user to adjust the output voltage precisely and set it to 12V.
To design the schematic and PCB, I used Altium Designer 24 and the Octopart website to quickly gather the necessary component information and generate the BOM. I used the Siglent SDL1020X-E DC Load and Siglent SDS2102X Plus oscilloscope to test the board for voltage drop, current delivery, and output noise. At the maximum output current, the output voltage drop is around 40mV only. 12V-7A AC to DC Switching Power Supply [SMPS]](https://i.ytimg.com/vi/etXycWuu9Gk/mqdefault.jpg)


![OPAMP Single/Dual Supply In Practice [Negative Rail and Positive Rail]
Single Supply vs Dual Supply OPAMP, Negative Rail and Positive Rail, EASY!
Voltage Follower
Check other videos: http://bit.ly/2N9OlPa
OPAMPs are very important components in Electronics, however they could be tricky even for experienced users. In this video, I prepared some experiments to show you how single supply and dual supply OPAMPs are different and why we should provide both positive rails and negative rails for the dual supply OPAMP in any case. The circuit configuration that I used is voltage follower.
In case of using a single supply OPAMP, if the input signal include a negative part, then we have to include the negative rail as well.
Just check your project requirements and read the datasheets carefully.
#opamp
#single_supply
#dual_supply OPAMP Single/Dual Supply In Practice [Negative Rail and Positive Rail]](https://i.ytimg.com/vi/hfo50ZzTQFE/mqdefault.jpg)




