Uploaded March 2026 | Updated November 2026, 1 day ago
9W AC LED Light Bulb
======================================
Altium Develop (Free Legal License): altium.com/yt/MyVanitar
======================================
Schematic & PCB: 365.altium.com/files/CA003187-C985-47C5-8D40-BDC15533C558
======================================
Other Videos: bit.ly/2N9OlPa
======================================
@AtiumOfficial
#altiumstories
In this video, I have reverse-engineered an AC LED light bulb, redrew its Schematic and PCB, and published my own version with some modifications/enhancements. It can be used for personal and educational purposes only.
The controller is the JD9609, which drives 10 9V-100mA 2835-series LEDs (on an MCPCB). So, in theory, the light bulb will have 9W of power, but due to practical limitations and LED lifetime concerns, the power should be around 7W.
The circuit is protected by a resistive fuse and a varistor.
9W AC LED Light Bulb
======================================
Altium Develop (Free Legal License): altium.com/yt/MyVanitar
======================================
Schematic & PCB: 365.altium.com/files/CA003187-C985-47C5-8D40-BDC15533C558
======================================
Other Videos: bit.ly/2N9OlPa
======================================
@AtiumOfficial
#altiumstories
In this video, I have reverse-engineered an AC LED light bulb, redrew its Schematic and PCB, and published my own version with some modifications/enhancements. It can be used for personal and educational purposes only.
The controller is the JD9609, which drives 10 9V-100mA 2835-series LEDs (on an MCPCB). So, in theory, the light bulb will have 9W of power, but due to practical limitations and LED lifetime concerns, the power should be around 7W.
The circuit is protected by a resistive fuse and a varistor.
![12V-7A AC to DC Switching Power Supply [SMPS]
12V-7A AC to DC Flyback Switching Power Supply [SMPS]
Article: https://www.powerelectronicsnews.com/12v-7a-ac-to-dc-flyback-switching-power-supply/
Altium Designer + Legal License (Free): https://www.altium.com/yt/myvanitar
Altium 365: https://www.altium.com/altium-365
OctoPart: https://octopart.com
Other Videos: http://bit.ly/2N9OlPa
The most essential part of any electronic device is the power supply unit. Any instability or malfunction in this part causes the device to stop its duty or show weird behavior. In this article/video, I introduced an AC-to-DC flyback switching power supply that converts 180V-260VAC to 12VDC, which can be used in a variety of applications.
The maximum power delivery of this power supply is 84W, which means it can handle 7A continuously at 12V output. The transformer can deliver higher currents, however, the educational purpose (hand winding of the transformer) and thermal stress on the switching controller were considered (the peak current of the controller’s MOSFET is around 2.3A, at 7A). The controller chip is KA1M0565, which operates using a 470K startup resistor and a small auxiliary winding on the transformer. The transformers ferrite core is ER28-17-11, and the switching frequency is 67KHz. A potentiometer allows the user to adjust the output voltage precisely and set it to 12V.
To design the schematic and PCB, I used Altium Designer 24 and the Octopart website to quickly gather the necessary component information and generate the BOM. I used the Siglent SDL1020X-E DC Load and Siglent SDS2102X Plus oscilloscope to test the board for voltage drop, current delivery, and output noise. At the maximum output current, the output voltage drop is around 40mV only. 12V-7A AC to DC Switching Power Supply [SMPS]](https://i.ytimg.com/vi/etXycWuu9Gk/mqdefault.jpg)


![OPAMP Single/Dual Supply In Practice [Negative Rail and Positive Rail]
Single Supply vs Dual Supply OPAMP, Negative Rail and Positive Rail, EASY!
Voltage Follower
Check other videos: http://bit.ly/2N9OlPa
OPAMPs are very important components in Electronics, however they could be tricky even for experienced users. In this video, I prepared some experiments to show you how single supply and dual supply OPAMPs are different and why we should provide both positive rails and negative rails for the dual supply OPAMP in any case. The circuit configuration that I used is voltage follower.
In case of using a single supply OPAMP, if the input signal include a negative part, then we have to include the negative rail as well.
Just check your project requirements and read the datasheets carefully.
#opamp
#single_supply
#dual_supply OPAMP Single/Dual Supply In Practice [Negative Rail and Positive Rail]](https://i.ytimg.com/vi/hfo50ZzTQFE/mqdefault.jpg)






![Standalone Full Bridge DC Motor Driver
Standalone Full Bridge (H Bridge) DC Motor Driver using Tiny13 and IR2104
Altium Designer + License (Free): https://www.altium.com/yt/myvanitar
OctoPart: https://octopart.com
Article: https://www.pcbway.com/blog/technology/A_Standalone_Full_Bridge_DC_Motor_Driver_2c7c2086.html
Other Videos: http://bit.ly/2N9OlPa
The Full-Bridge (H-Bridge) is the most popular driver circuit to control brushed DC motors. The main advantage of a full bridge driver is the ability to change the rotation direction of the motor, without manually reversing the supply wires. I’ve already published the Half-bridge and H-bridge driver circuits before; however, I was receiving many requests and comments for a standalone H-Bridge driver to control the DC motors, without using any external board or a controller.
Therefore, I introduced a cheap, compact, and standalone H-Bridge DC motor driver that can be embedded in a variety of mechatronic devices. A cheap ATTiny13 microcontroller controls everything and I used the Arduino IDE to write the microcontroller code. All components, except for the connectors, are SMD.
The motor can be controlled in three modes: Forward, Stop, and Reverse. The user can adjust the rotation speed of the motor separately in the forward or reverse direction, using two panel-mounting potentiometers. The low ON-Resistance of the Mosfets allows you to use this circuit in high currents.
To design the schematic and PCB, I used Altium Designer 22. The fast component search engine (octopart) allowed me to quickly collect the components’ data and generate the BOM as well. To get high-quality fabricated boards, I sent the Gerber files to PCBWay. To test the driver board, I disassembled an electric toy car and used its powerful 775 DC motor (plus the gearbox).
It’s a cool experience, just build one and have fun!
Specifications
Input Voltage (Motor): 8-40VDC
Supply Voltage (Controller): 12VDC
PWM Frequency: 25KHz
Motor Control: Forward-Stop-Reverse
Motor Speed: [0 to 100%] Forward, [0 to 100%] Reverse Standalone Full Bridge DC Motor Driver](https://i.ytimg.com/vi/lbVwRdweDYA/mqdefault.jpg)