Uploaded August 2022 | Updated November 2026, 3 days ago
In this video, I've explained how to Spot or identify a Fake Soldering Iron or soldering station. You can follow my test using an AC energy measurement circuit (previously published project) that can measure the active power of any AC load as well.
all my soldering irons were ceramic-based, which means the heating element is ceramic. You will be amazed when you realize a 40W soldering Iron is actually 10W.
======================================
Altium Designer + License (Free): altium.com/yt/myvanitar
OctoPart: octopart.com
======================================
In this video, I've explained how to Spot or identify a Fake Soldering Iron or soldering station. You can follow my test using an AC energy measurement circuit (previously published project) that can measure the active power of any AC load as well.
all my soldering irons were ceramic-based, which means the heating element is ceramic. You will be amazed when you realize a 40W soldering Iron is actually 10W.
======================================
Altium Designer + License (Free): altium.com/yt/myvanitar
OctoPart: octopart.com
======================================

![12V-7A AC to DC Switching Power Supply [SMPS]
12V-7A AC to DC Flyback Switching Power Supply [SMPS]
Article: https://www.powerelectronicsnews.com/12v-7a-ac-to-dc-flyback-switching-power-supply/
Altium Designer + Legal License (Free): https://www.altium.com/yt/myvanitar
Altium 365: https://www.altium.com/altium-365
OctoPart: https://octopart.com
Other Videos: http://bit.ly/2N9OlPa
The most essential part of any electronic device is the power supply unit. Any instability or malfunction in this part causes the device to stop its duty or show weird behavior. In this article/video, I introduced an AC-to-DC flyback switching power supply that converts 180V-260VAC to 12VDC, which can be used in a variety of applications.
The maximum power delivery of this power supply is 84W, which means it can handle 7A continuously at 12V output. The transformer can deliver higher currents, however, the educational purpose (hand winding of the transformer) and thermal stress on the switching controller were considered (the peak current of the controllerās MOSFET is around 2.3A, at 7A). The controller chip is KA1M0565, which operates using a 470K startup resistor and a small auxiliary winding on the transformer. The transformers ferrite core is ER28-17-11, and the switching frequency is 67KHz. A potentiometer allows the user to adjust the output voltage precisely and set it to 12V.
To design the schematic and PCB, I used Altium Designer 24 and the Octopart website to quickly gather the necessary component information and generate the BOM. I used the Siglent SDL1020X-E DC Load and Siglent SDS2102X Plus oscilloscope to test the board for voltage drop, current delivery, and output noise. At the maximum output current, the output voltage drop is around 40mV only. 12V-7A AC to DC Switching Power Supply [SMPS]](https://i.ytimg.com/vi/etXycWuu9Gk/mqdefault.jpg)


![OPAMP Single/Dual Supply In Practice [Negative Rail and Positive Rail]
Single Supply vs Dual Supply OPAMP, Negative Rail and Positive Rail, EASY!
Voltage Follower
Check other videos: http://bit.ly/2N9OlPa
OPAMPs are very important components in Electronics, however they could be tricky even for experienced users. In this video, I prepared some experiments to show you how single supply and dual supply OPAMPs are different and why we should provide both positive rails and negative rails for the dual supply OPAMP in any case. The circuit configuration that I used is voltage follower.
In case of using a single supply OPAMP, if the input signal include a negative part, then we have to include the negative rail as well.
Just check your project requirements and read the datasheets carefully.
#opamp
#single_supply
#dual_supply OPAMP Single/Dual Supply In Practice [Negative Rail and Positive Rail]](https://i.ytimg.com/vi/hfo50ZzTQFE/mqdefault.jpg)





