Master Cylinder Removal and Install Tips and Tricks @AutoRestoMod

Uploaded April 2025 | Updated September 2026, 1 day ago

We walk you through the complete process of how I go about removing an old master cylinder and installing a new one. You'll learn the best techniques to loosen tube nuts without twisting or damaging them. We also demonstrate how to properly bench bleed the master cylinder before installation to ensure a smooth and effective brake system operation.

In this video:
How to safely remove your old master cylinder
The right way to loosen tube nuts without damage
Bench bleeding techniques for a trouble-free install
Step-by-step installation of the new master cylinder

Whether you're a beginner or an experienced DIYer, this guide will help you get the job done right! If you find this video helpful, don’t forget to like, comment, and subscribe for more automotive repair tips.

Got questions? Drop them in the comments below!

#MasterCylinder #BrakeRepair #CarMaintenance #DIYAutoRepair #BenchBleeding

Episode 282 Manic Mechainc

#ClassicCar #FuelSystem #CarRestoration #BarnFind #CarDIY

Master Cylinder Removal and Install Tips and Tricks

I Quit Welding Rusty Floor Pans — Heres My Fix

I Almost Quit This 1967 Mustang Floor Repair

What Would You do to This Barn Find Classic Car

I Modified an Air Chisel to Beat 50 Year Old Spot Welds

How to Polish Oxidized Aluminum Wheels (On the Car!)

$Cheap tricks for a Clean Wiring Install on Your Classic Car Last week we neatened up the charging system and set it up for our CVF Racing serpentine belt system. This week we deal with the leftovers — the wiring somebody else left behind in this engine bay — and turn a tangle of mismatched harness into something that looks like it belongs. This isnt a jot-and-tittle, every-wire walkthrough. Its the tips and tricks that make the difference: start with a plan, drape and route your wires toward where they actually need to land, and decide up front where things like corrugated loom belong (and where they dont). We work through the American Autowire engine harness, the VSS leads for a future speed-sensor setup, and the runs out to the water temperature and oil pressure senders — leaving access for whatever Kylie may want to add down the road. Along the way we run into the usual first vexation of any classic-car project: figuring out what the last fellow cobbled together and why. In this case its the wire feeding the start circuit at the starter solenoid — a small thing that tells you everything about how the car was wired before it got here. What came in as a fifteen-minute, four-bolt transmission job on this 67 Mustang turned into a tour through every system — suspension, transmission, engine, and interior. Kylies ready to drive it, and so are we. It just takes a few more careful tweaks like this one. Our thanks to National Parts Depot for helping keep these classic Fords on the road. If this helped with your own build, consider supporting the shop through our Patreon — that support goes straight to the kids who turn wrenches with us on Saturdays. #ClassicCarWiring #67Mustang #AmericanAutowire #EngineBayDetailing #AutoRestoMod Its not a problem, its a project. — ▶ Autorestomod is proudly sponsored by National Parts Depot — [https://www.npdlink.com] ▶ Starter solenoid & Mustang restoration parts — National Parts Depot: [link] ▶ Charging system & 100-amp alternator — CVF: [https://cvfracing.com/] ▶ Battery cables & welding wire — Fast and Quiet: [link] SUPPORT THE SHOW ▶ Patreon — $10/month gets you monthly Zoom meetings with me: [https://www.patreon.com/c/gasolinemedia] ▶ Merch — Needs More Classic Cars shirts, hats & mugs at Fourth Wall: [https://autorestomod-shop.fourthwall.com/] It’s not a Problem, It’s a Project! Autorestomod Episode: 747 https://autorestomod-shop.fourthwall.com/ Sponsors: https://www.nationalpartsdepot.com https://www.eatondetroitspring.com https://www.moderndriveline.com Contact: Jford@autorestomod.com Insta: @autorestomod www.patreon.com/gasolinemedia. #Autorestomod #1967Mustang #Restomod #ClassicCarRestoration #AutomotiveWiring$

Well, its not a problem, its a project #f100 #autorestomod #partscar