Uploaded August 2025 | Updated November 2026, 6 hours ago
This project is a robust and efficient isolated DC-DC converter based on the flyback topology, designed to handle a wide input voltage range from 50V to 300V DC, making it ideal for industrial, automotive, or renewable energy applications where input voltage fluctuations are common.
Key Features:
Input Voltage Range: 50V – 300V DC
Output 1: 5V @ 500mA (isolated)
Output 2: 3.3V @ 500mA (isolated)
Output 3: 15V @ 300mA (independent isolated winding)
Controller IC: OB2273
Topology: Flyback with transformer-based galvanic isolation
Switching Frequency: ~65kHz (typical for OB2273 applications)
Protections: OVP, SCP, UVLO, cycle-by-cycle current limiting
Controller IC – OB2273 Overview
The OB2273 is a highly integrated current-mode PWM controller from On-Bright Electronics, specifically designed for offline isolated Flyback converters. It features:
Integrated high-voltage startup circuit for simplifying design and reducing standby loss.
Internal soft-start, frequency jittering for EMI reduction, and cycle-by-cycle current limiting.
Green mode operation, which reduces switching frequency at light load to improve efficiency and meet Energy Star or DOE Level VI power consumption targets.
Design Considerations
A custom multi-output Flyback transformer was designed to deliver tightly regulated 5V and 3.3V outputs with shared ground, and an independently isolated 15V output for control, feedback, or analog circuitry.
Cross-regulation techniques (e.g., dummy loads or active regulation) were used to maintain output stability across varying loads.
Optocoupler feedback was implemented from the 5V rail to regulate the main control loop, with auxiliary windings supporting startup and biasing.
A snubber circuit (RCD or TVS clamp) was used across the transformer primary to handle leakage inductance and improve switching efficiency.
Applications
Industrial sensor and controller nodes
Isolated gate drivers or analog front ends
Battery-powered or solar applications needing galvanic isolation
Microcontroller-based systems with multiple voltage domains
Advantages
Operates reliably across a very wide DC input range, suitable for harsh and variable environments
High efficiency and low standby power consumption due to OB2273’s green-mode control
Full isolation ensures safety and noise immunity between the control and power sections
Compact and cost-effective thanks to single-switch Flyback design
This project is a robust and efficient isolated DC-DC converter based on the flyback topology, designed to handle a wide input voltage range from 50V to 300V DC, making it ideal for industrial, automotive, or renewable energy applications where input voltage fluctuations are common.
Key Features:
Input Voltage Range: 50V – 300V DC
Output 1: 5V @ 500mA (isolated)
Output 2: 3.3V @ 500mA (isolated)
Output 3: 15V @ 300mA (independent isolated winding)
Controller IC: OB2273
Topology: Flyback with transformer-based galvanic isolation
Switching Frequency: ~65kHz (typical for OB2273 applications)
Protections: OVP, SCP, UVLO, cycle-by-cycle current limiting
Controller IC – OB2273 Overview
The OB2273 is a highly integrated current-mode PWM controller from On-Bright Electronics, specifically designed for offline isolated Flyback converters. It features:
Integrated high-voltage startup circuit for simplifying design and reducing standby loss.
Internal soft-start, frequency jittering for EMI reduction, and cycle-by-cycle current limiting.
Green mode operation, which reduces switching frequency at light load to improve efficiency and meet Energy Star or DOE Level VI power consumption targets.
Design Considerations
A custom multi-output Flyback transformer was designed to deliver tightly regulated 5V and 3.3V outputs with shared ground, and an independently isolated 15V output for control, feedback, or analog circuitry.
Cross-regulation techniques (e.g., dummy loads or active regulation) were used to maintain output stability across varying loads.
Optocoupler feedback was implemented from the 5V rail to regulate the main control loop, with auxiliary windings supporting startup and biasing.
A snubber circuit (RCD or TVS clamp) was used across the transformer primary to handle leakage inductance and improve switching efficiency.
Applications
Industrial sensor and controller nodes
Isolated gate drivers or analog front ends
Battery-powered or solar applications needing galvanic isolation
Microcontroller-based systems with multiple voltage domains
Advantages
Operates reliably across a very wide DC input range, suitable for harsh and variable environments
High efficiency and low standby power consumption due to OB2273’s green-mode control
Full isolation ensures safety and noise immunity between the control and power sections
Compact and cost-effective thanks to single-switch Flyback design








![12V-7A AC to DC Switching Power Supply [SMPS]
12V-7A AC to DC Flyback Switching Power Supply [SMPS]
Article: https://www.powerelectronicsnews.com/12v-7a-ac-to-dc-flyback-switching-power-supply/
Altium Designer + Legal License (Free): https://www.altium.com/yt/myvanitar
Altium 365: https://www.altium.com/altium-365
OctoPart: https://octopart.com
Other Videos: http://bit.ly/2N9OlPa
The most essential part of any electronic device is the power supply unit. Any instability or malfunction in this part causes the device to stop its duty or show weird behavior. In this article/video, I introduced an AC-to-DC flyback switching power supply that converts 180V-260VAC to 12VDC, which can be used in a variety of applications.
The maximum power delivery of this power supply is 84W, which means it can handle 7A continuously at 12V output. The transformer can deliver higher currents, however, the educational purpose (hand winding of the transformer) and thermal stress on the switching controller were considered (the peak current of the controller’s MOSFET is around 2.3A, at 7A). The controller chip is KA1M0565, which operates using a 470K startup resistor and a small auxiliary winding on the transformer. The transformers ferrite core is ER28-17-11, and the switching frequency is 67KHz. A potentiometer allows the user to adjust the output voltage precisely and set it to 12V.
To design the schematic and PCB, I used Altium Designer 24 and the Octopart website to quickly gather the necessary component information and generate the BOM. I used the Siglent SDL1020X-E DC Load and Siglent SDS2102X Plus oscilloscope to test the board for voltage drop, current delivery, and output noise. At the maximum output current, the output voltage drop is around 40mV only. 12V-7A AC to DC Switching Power Supply [SMPS]](https://i.ytimg.com/vi/etXycWuu9Gk/mqdefault.jpg)

