Uploaded September 2016 | Updated November 2026, 4 hours ago
For this reaction a selfmade Iron(III) soluton was used. The results might be better with a clean commercial product. The Fe(III)-Chloride solution was neutralized using Sodium Carbonate till an insoluble precipitate had formed. To this a few drops of HCl (35%) were added (under stirring). As soon as the solution appeared to be transparent again solid Sodium Acetate was added.
A red complex forms. It's composition is hard to explain, thus we recommend acutally looking at a picture of this compound. Other transition metals form similar polynuclear complexes with Acetates.
For this reaction a selfmade Iron(III) soluton was used. The results might be better with a clean commercial product. The Fe(III)-Chloride solution was neutralized using Sodium Carbonate till an insoluble precipitate had formed. To this a few drops of HCl (35%) were added (under stirring). As soon as the solution appeared to be transparent again solid Sodium Acetate was added.
A red complex forms. It's composition is hard to explain, thus we recommend acutally looking at a picture of this compound. Other transition metals form similar polynuclear complexes with Acetates.

![Tellurium Chemistry: Tellurium in HNO3 [2x]
In this video, we heat some Te in HNO3. Right as we add the black powder to the acid the acid turns yellow due to the formation of NOx gases. Heating the mixture causes the Te to produce a lot of gas bubbles while forming a thick brown gas. When we bubbled air through it later the acid became nearly colorless again.
What is happening is that the Te reduces the HNO3 to NOx, which forms yellow-red fumes while being oxidized to TeO2, which is colorless. Tellurium Chemistry: Tellurium in HNO3 [2x]](https://i.ytimg.com/vi/VRlKMVKwKjk/mqdefault.jpg)



 from PdCl2
We mentioned in another video that we werent sure about what product might form if PdCl2 reacted with KCN. After a big search in old literature, we found a line that proves the formation of Tetracyanopalladate(II) if KCN is added to PdCl2 or [PdCl4](2-). And as you can see once we add it the brown color disappears. Palladium Chemistry: [Pd(CN)4](2-) from PdCl2](https://i.ytimg.com/vi/XHbn9Z3EaAA/mqdefault.jpg)




![Titanium Chemisty: Titanium in HF [8x faster]
The preparations for this experiment started with us finding a line in an old chemistry textbook saying Ti would dissolve quite well in HF. As you probably know, it usually takes high temperatures and long periods until Ti dissolves in anything (check out our TiCl3 video for that). Therefore, we thought we could try this with HF, note the HF has around 40% concentration so around the HCl and the temperature was around 20°C when we did that so at cooler temperatures.
We filled a test tube with 5 ml of HF (40%) and added a small piece of Ti wire. The reaction started immediately quickly producing a purple - pink solution At some point, we added a bit of water. The color changes to green. In the end, you can see two layers, the upper one is the aqueous Ti-complex and the bottom one is insoluble [SiF6](2-).
The question is why does it react with HF better than with HCl? And we cant really find a suitable explanation. The fact that HF attacks glass is probably something different here. It could be because very stable Fluorocomplexes are formed. Elements like Zirconium, Titanium, even Iron are known to form stable Fluoride complexes although usually, Fluoride is a weak ligand. Titanium(III) and (IV) especially in acids also tends to form Titanyl, TiO2 and hydrated oxygen-rich species. So perhaps the equilibrium shifts towards the fluoride here because it resists the back-reaction to some extend and the passive layer is therefore destroyed.
And to be honest we have no clue what is happening in this experiment at all. Even the Gmelin does not really talk a lot about the chemistry between HF and Ti metal. According to other books, the following reaction is very likely:
Much like with HCl, HF dissolves the Ti to form Ti(III). For the chloro-species, there are many isomers much like with Chromium. While the [Ti(H2O)6]Cl3 and also the [Ti(H2O)6]F3 are said to be purple-red their isomer, [Ti(H2O)4Cl2]Cl is green. And we think this is the case for the fluoro complex as well.
The question remains why this happens here and not the other way around? What might happen is that the pure Hexaqua-complex acts as a cationic acid and is deprotanted as the conc. of H(+) from HF is diluted with the addition of water. Then the famous Titanium-Oxy and Hydroxy-species form and perhaps somewhere in this cycle Fluoride can take the positions.
If you find anything about the actual reaction we would be really interested to hear about it.
Also if you ask yourself why we think the colors here are purple and green. We ran this experiment twice before with different concentrations and it would always self-heat to a point where it got out of control producing much more intense colored compounds which were really deep purple and grass green. Titanium Chemisty: Titanium in HF [8x faster]](https://i.ytimg.com/vi/Z44cBRfHm_k/mqdefault.jpg)