Uploaded October 2026 | Updated November 2026, 5 days ago
This was filmed in accommodation at work, so the environment and sound will be different. (I'm back at the usual bench now.)
Initially I was a bit suspicious about this device which is basically a USB powered ioniser.
There was a possibility it might be fake and not have high voltage circuitry, or if it did then it may have an issue where an ioniser creates a huge DC voltage differential with respect to ground and can stress the primary to secondary insulation of power supplies.
It turns out that this is a very simple implementation of a bipolar ioniser where a high voltage differential is applied between two carbon fibre tufts, causing ion flow between them. This results in a slight dust precipitation effect, but more importantly it produces a very tiny amount of corona discharge on the ultra fine tips of the carbon fibre tufts.
When air is exposed to a corona discharge some amazing science happens. Air molecules are split apart into separate atoms momentarily, and when they recombine, some can form short lived active gas molecules like ozone (O3), hydroxyl radicals (OH), hydrogen peroxide (O2H2) and many others. These molecules are unstable, and in the process of rapidly reverting back to a stable form they donate their unwanted atoms to anything in the air. That could be viruses, bacteria and organic compounds. In the process of doing so they can deactivate them and reduce odours.
This is done at a very low trace level as happens in natural outdoor air.
A good example of a bipolar ioniser is Sharp's famous Plasmacluster air sterilising system.
The module could also be used as a convenient source of high voltage at very low current for specialist projects too.
If you want to get one to play with then here's a link to the item on AliExpress (not a sponsor).
This is an affiliate link, but that will not affect the price you pay.
https://s.click.aliexpress.com/e/_c4T0oZHX
If you enjoy my videos you can buy me coffee, cookies and gadgets with a small contribution on Patreon. That also gives early access without adverts when I upload a new video, bonus footage and regular quiet Patreon live streams.
patreon.com/bigclive
Alternatively, for a single coffee contribution you can use PayPal:-
paypal.com/paypalme/bigclive
#ElectronicsCreators
This was filmed in accommodation at work, so the environment and sound will be different. (I'm back at the usual bench now.)
Initially I was a bit suspicious about this device which is basically a USB powered ioniser.
There was a possibility it might be fake and not have high voltage circuitry, or if it did then it may have an issue where an ioniser creates a huge DC voltage differential with respect to ground and can stress the primary to secondary insulation of power supplies.
It turns out that this is a very simple implementation of a bipolar ioniser where a high voltage differential is applied between two carbon fibre tufts, causing ion flow between them. This results in a slight dust precipitation effect, but more importantly it produces a very tiny amount of corona discharge on the ultra fine tips of the carbon fibre tufts.
When air is exposed to a corona discharge some amazing science happens. Air molecules are split apart into separate atoms momentarily, and when they recombine, some can form short lived active gas molecules like ozone (O3), hydroxyl radicals (OH), hydrogen peroxide (O2H2) and many others. These molecules are unstable, and in the process of rapidly reverting back to a stable form they donate their unwanted atoms to anything in the air. That could be viruses, bacteria and organic compounds. In the process of doing so they can deactivate them and reduce odours.
This is done at a very low trace level as happens in natural outdoor air.
A good example of a bipolar ioniser is Sharp's famous Plasmacluster air sterilising system.
The module could also be used as a convenient source of high voltage at very low current for specialist projects too.
If you want to get one to play with then here's a link to the item on AliExpress (not a sponsor).
This is an affiliate link, but that will not affect the price you pay.
https://s.click.aliexpress.com/e/_c4T0oZHX
If you enjoy my videos you can buy me coffee, cookies and gadgets with a small contribution on Patreon. That also gives early access without adverts when I upload a new video, bonus footage and regular quiet Patreon live streams.
patreon.com/bigclive
Alternatively, for a single coffee contribution you can use PayPal:-
paypal.com/paypalme/bigclive
#ElectronicsCreators








![Making a laser lumia/aura effects disk - with a slight silicone disaster
The Lumia or Aura effect is created by shining a laser through rippled glass, but it can be difficult to find the right glass, and someone who can cut a circle from it for you. This was an experiment to use a standard filament based 3D printer to create a silicone mould for optically clear resin.
This was my first attempt at creating a mould with liquid silicone. Apparently platinum-cured silicone is very fussy about what its used with, and my master shape was fine on its own, but when pre-textured with UV cured resin it prevented the silicone from curing in that area and caused an outgassing effect. Even with ordinary two-part resin the silicone still stayed slightly sticky where it was in contact.
In the end the answer was to use the 3D printed PLA mould on its own and add the effects onto the cast resin disks afterwards.
When using UV curing resin I strongly recommend wearing gloves to protect your hands from contact with it. The chemicals used to make it light sensitive can also make your skin sensitive to sunlight.
This is an experimental device. I dont know how the resin will hold up to specific wavelengths of laser energy. Its also probably limited to low power lasers for safety. The disk can also be used with various styles of LEDs for an aurora borealis effect.
For laser use the disk should rotate very slowly to get the best optical warping effects.
Heres the OpenSCAD script that creates your custom mould for this project.
There are two adjustable variables - one for the outer diameter of the disk and one for the central hub where it attaches to a suitable motor. The script will automatically place a small central indent for aligning a drill if needed.
OpenSCAD can be downloaded for Windows, Linux and Mac (plus others) from the official site:-
https://openscad.org/
To use the script, copy and paste it into the left hand editor window in openscad. You can either adjust the two variables directly in the script or you can enable the customizer that will open a window to do it.
If you want to use the customizer then you can open it from the window drop down menu.
To see the results of any changes quickly, press the cube-button with two arrows on it. To do the full build press the cube-button with the hourglass on it, and when it is complete, save the file by pressing the STL button.
That will save a design file that can be used in your choice of slicer for 3D printing.
The script is below:-
//Ripple disk mould maker
//Diameter of disk in mm
dia=75;
//Diameter of central hub in mm
hub=20;
difference(){
cylinder(h=12,d=dia+12);
translate([0,0,1])
cylinder(h=12,d=dia+10);
}
difference(){
union(){
cylinder(h=5,d=dia);
cylinder(h=7,d=hub);
}
//Central drilling indent
translate([0,0,5.5])
cylinder(h=2,d1=0,d2=3);
}
$fn=100; Making a laser lumia/aura effects disk - with a slight silicone disaster](https://i.ytimg.com/vi/5yNYqsbBkJM/mqdefault.jpg)

