Uploaded September 2026 | Updated November 2026, 1 day ago
In Part 2 of building my custom 3D-printed AI desktop assistant, we run the initial demo and go through options during which time an issues was found and analyzed causing a redesign of the unit which was then re-tested and demo'ed
TIMESTAMPS:
0:00 - Recap of Part one
1:06 - Demo of Initial Configuration and Options
4:03 - Basic Acoustic Diagnostics
6:45 - Design Failure and Acoustic Analysis
9:07 - The Re-Design
10:03 - Assembly
11:10 - Re-Redesign and Assembly
17:17 - Post Rebuild Testing
HARDWARE & COMPONENTS USED:
- ESP32 Development Board
- OLED / TFT Display Module
- I2S Microphone & Audio Amplifier / Speaker
- Custom 3D Printed Chassis
3D PRINT FILES (STLs):
makerworld.com/en/models/3324770-lilygo-t5-e-paper-esp32-case
ESP32 Software for the project: github.com/jordancrubin/ESP32-AI-Module
WATCH PART 1 (Firmware & Live AI Demo): youtube.com/watch?v=0tuumnskRkU
ESP32 N16R8
amzn.to/4enfSts
ICS43434 Microphone [2 for beamforming]
amzn.to/4enfSts
2Pack 8 Ohm 3W speakers
amzn.to/3PgiSNR
BME680 Envitonmental monitoring sensor
amzn.to/4teaRHc
MAX98357 Amplifier 3W
amzn.to/4teaRHc
USB C Power connectors
amzn.to/4teaRHc
Protoboard
amzn.to/496qjhk
Crimp connector kit
amzn.to/48zZiCK
As an Amazon Associate I earn from qualifying purchases. If you choose to purchase any of these items the links above provide a small commission that I use towards the making of these videos at no additional cost to you.
#ESP32 #3DPrinting #ArtificialIntelligence #DIYTech #Maker #EmbeddedSystems #DesktopSetup
In Part 2 of building my custom 3D-printed AI desktop assistant, we run the initial demo and go through options during which time an issues was found and analyzed causing a redesign of the unit which was then re-tested and demo'ed
TIMESTAMPS:
0:00 - Recap of Part one
1:06 - Demo of Initial Configuration and Options
4:03 - Basic Acoustic Diagnostics
6:45 - Design Failure and Acoustic Analysis
9:07 - The Re-Design
10:03 - Assembly
11:10 - Re-Redesign and Assembly
17:17 - Post Rebuild Testing
HARDWARE & COMPONENTS USED:
- ESP32 Development Board
- OLED / TFT Display Module
- I2S Microphone & Audio Amplifier / Speaker
- Custom 3D Printed Chassis
3D PRINT FILES (STLs):
makerworld.com/en/models/3324770-lilygo-t5-e-paper-esp32-case
ESP32 Software for the project: github.com/jordancrubin/ESP32-AI-Module
WATCH PART 1 (Firmware & Live AI Demo): youtube.com/watch?v=0tuumnskRkU
ESP32 N16R8
amzn.to/4enfSts
ICS43434 Microphone [2 for beamforming]
amzn.to/4enfSts
2Pack 8 Ohm 3W speakers
amzn.to/3PgiSNR
BME680 Envitonmental monitoring sensor
amzn.to/4teaRHc
MAX98357 Amplifier 3W
amzn.to/4teaRHc
USB C Power connectors
amzn.to/4teaRHc
Protoboard
amzn.to/496qjhk
Crimp connector kit
amzn.to/48zZiCK
As an Amazon Associate I earn from qualifying purchases. If you choose to purchase any of these items the links above provide a small commission that I use towards the making of these videos at no additional cost to you.
#ESP32 #3DPrinting #ArtificialIntelligence #DIYTech #Maker #EmbeddedSystems #DesktopSetup
![Aerogarden Bounty Elite Vs. Amazons Cheapest Comparable Knockoff [UPDATE]
Folks have asked for an update on the Aerogarden Bounty Knockoff, and I happened to be up in New England with some more info on the unit after four months along with a moving adventure with a subsequent post move setup down south.
Bounty Elite: https://amzn.to/4019mxX
AFFLAT unit: https://amzn.to/3Jf8cbv
AeroGarden Heirloom Salad Greens Mix Seed Pod Kit - 6-Pod
https://amzn.to/3lAsCUm
AeroGarden Sweet Bell Peppers Seed Pod Kit (9-pod)
https://amzn.to/3lzI9nx
AeroGarden Liquid Nutrients (1 Liter)
https://amzn.to/3LOvEiI
As an Amazon Associate I earn from qualifying purchases. If you choose to purchase any of these items the links above provide a small commission that I use towards the making of these videos at no additional cost to you.
#aerogarden #hydroponics #diygarden Aerogarden Bounty Elite Vs. Amazons Cheapest Comparable Knockoff [UPDATE]](https://i.ytimg.com/vi/cpKWoYa6Mnw/mqdefault.jpg)









