Uploaded September 2023 | Updated November 2026, 2 days ago
Digital AC Energy Measurement Circuit V2, RMS Voltage, RMS Current, Real Power, Power Factor, KWh
======================================
Altium Designer + Legal License (Free): altium.com/yt/myvanitar
======================================
Altium 365: altium.com/altium-365
======================================
OctoPart: octopart.com
======================================
Article: pcbway.com/blog/technology/Digital_AC_Energy_Measurement_Circuit_V2_RMS_Voltage_RMS_Current_Real_Power_P_a1bf4da8.html
======================================
Gerber/PCB Order: pcbway.com/project/shareproject/Gerber_AC_Energy_Meter_Rev_2_0_09cdc370.html
======================================
Other Videos: bit.ly/2N9OlPa
======================================
Disclaimer: Some parts of this circuit carry dangerous Mains voltage. If you are a beginner, seek guidance from experienced users.
Dealing with the 110V/220V AC mains voltage and measuring the AC load parameters are regarded as a challenge for electronic designers in circuit design and calculations. The situation becomes more complex when dealing with inductive loads because they cause a phase shift between voltage and current and alter the sine-wave shape of the AC signal (resistive loads do not). The power factor of resistive loads is theoretically equal to 1.
In this article/video, I introduce a circuit that can measure AC RMS voltage, RMS current, active power, power factor, and energy consumption (KWh) of the loads. I used a low-cost STM32 Microcontroller and provided four push buttons for initial calibration. The device can independently measure the parameters and display the results on a bright 1.3-inch OLED display. The measurement error rate is around 0.5% or lower.
For the schematic and PCB design, I use Altium Designer 23. I shared the PCB project with my colleague for feedback and edits through Altium 365's secure cloud space. The Octopart component search engine proves invaluable for obtaining component information and generating the Bill-of-Materials (BOM). To ensure the production of high-quality fabricated boards, I forwarded the Gerber files to PCBWay. I used the Siglent SDM3045X benchtop multimeter to calibrate the circuit. That’s a quick and easy process.
It's a cool device for everyday electronics, so let’s get started! :-)
Digital AC Energy Measurement Circuit V2, RMS Voltage, RMS Current, Real Power, Power Factor, KWh
======================================
Altium Designer + Legal License (Free): altium.com/yt/myvanitar
======================================
Altium 365: altium.com/altium-365
======================================
OctoPart: octopart.com
======================================
Article: pcbway.com/blog/technology/Digital_AC_Energy_Measurement_Circuit_V2_RMS_Voltage_RMS_Current_Real_Power_P_a1bf4da8.html
======================================
Gerber/PCB Order: pcbway.com/project/shareproject/Gerber_AC_Energy_Meter_Rev_2_0_09cdc370.html
======================================
Other Videos: bit.ly/2N9OlPa
======================================
Disclaimer: Some parts of this circuit carry dangerous Mains voltage. If you are a beginner, seek guidance from experienced users.
Dealing with the 110V/220V AC mains voltage and measuring the AC load parameters are regarded as a challenge for electronic designers in circuit design and calculations. The situation becomes more complex when dealing with inductive loads because they cause a phase shift between voltage and current and alter the sine-wave shape of the AC signal (resistive loads do not). The power factor of resistive loads is theoretically equal to 1.
In this article/video, I introduce a circuit that can measure AC RMS voltage, RMS current, active power, power factor, and energy consumption (KWh) of the loads. I used a low-cost STM32 Microcontroller and provided four push buttons for initial calibration. The device can independently measure the parameters and display the results on a bright 1.3-inch OLED display. The measurement error rate is around 0.5% or lower.
For the schematic and PCB design, I use Altium Designer 23. I shared the PCB project with my colleague for feedback and edits through Altium 365's secure cloud space. The Octopart component search engine proves invaluable for obtaining component information and generating the Bill-of-Materials (BOM). To ensure the production of high-quality fabricated boards, I forwarded the Gerber files to PCBWay. I used the Siglent SDM3045X benchtop multimeter to calibrate the circuit. That’s a quick and easy process.
It's a cool device for everyday electronics, so let’s get started! :-)




![How to Design the Component Libraries in Altium Designer [Beginners Tutorial]
How to Design the Component Libraries in Altium Designer [From Scratch]
Altium Designer + License (Free): https://www.altium.com/yt/myvanitar
In this video, you will learn (Altium Designer beginners tutorial) how to design/create a schematic symbol and a PCB footprint (a component library) in Altium designer and attach a 3D model to the footprint. Basically, you will create an integrated library and then you will add a schematic symbol and the PCB footprint. Then you are ready to compile the library and use it. My selected component is the LM358 opamp with the DIP8 package.
CHAPTERS
00:00 - Introduction
00:24 - 4 Methods of importing the component libraries in your PCB project
01:10 - How to design a Schematic symbol in Altium Designer
11:17 - How to design a PCB Footprint in Altium Designer
18:04 - How to add an external 3D model to the PCB footprint
20:30 - How to compile the integrated library and use the pre-build library
Music by Atch
SoundCloud: https://bit.ly/AtchSoundCloud
Spotify: https://bit.ly/AtchSpotify
Instagram: https://instagram.com/atchmusic How to Design the Component Libraries in Altium Designer [Beginners Tutorial]](https://i.ytimg.com/vi/J_pZdNdJaAs/mqdefault.jpg)





