Uploaded January 2024 | Updated November 2026, 2 days ago
Detecting Failed Capacitors, Unveiling the Secrets (Capacitance, ESR, Phase Angle, Dissipation Factor)
======================================
Article: eeweb.com/detecting-failed-capacitors-unveiling-the-secrets-capacitance-esr-phase-angle-dissipation-factor
======================================
Altium Designer + Legal License (Free): altium.com/yt/myvanitar
======================================
OctoPart: octopart.com
======================================
Other Videos: bit.ly/2N9OlPa
======================================
Capacitors are essential components in electronics, primarily used for bypassing and decoupling. Depending on the capacitor type and its application, it is prone to aging and failure.
Detecting a failed capacitor is easy sometimes just by performing a visual inspection, but there are many cases in which you would need an LCR meter to spot any failure. In this article, I covered the most common failure cases of electrolytic, polyester (MKT), and ceramic (MLCC) type capacitors you will frequently encounter in your repair attempts. I considered four testing parameters: DC resistance, temperature, capacitance, ESR, dissipation factor (D), and phase angle (theta).
Detecting Failed Capacitors, Unveiling the Secrets (Capacitance, ESR, Phase Angle, Dissipation Factor)
======================================
Article: eeweb.com/detecting-failed-capacitors-unveiling-the-secrets-capacitance-esr-phase-angle-dissipation-factor
======================================
Altium Designer + Legal License (Free): altium.com/yt/myvanitar
======================================
OctoPart: octopart.com
======================================
Other Videos: bit.ly/2N9OlPa
======================================
Capacitors are essential components in electronics, primarily used for bypassing and decoupling. Depending on the capacitor type and its application, it is prone to aging and failure.
Detecting a failed capacitor is easy sometimes just by performing a visual inspection, but there are many cases in which you would need an LCR meter to spot any failure. In this article, I covered the most common failure cases of electrolytic, polyester (MKT), and ceramic (MLCC) type capacitors you will frequently encounter in your repair attempts. I considered four testing parameters: DC resistance, temperature, capacitance, ESR, dissipation factor (D), and phase angle (theta).



![LM317 Current Boosting Circuits [2N3055, MJ2955]
LM317 Current Boost Circuits using 2N3055 and MJ2955
Altium Designer + License (Free): https://www.altium.com/yt/myvanitar
Article Source (Schematic, Details): https://www.pcbway.com/blog/technology/LM317_Current_Boosting_Secrets.html
Check other videos: http://bit.ly/2N9OlPa
#LM317
LM317 is one of the most popular adjustable regulator chips. The output voltage of the regulator can be adjusted from 1.25V to 35V. However, the chip can deliver currents up to 1.5A which is not enough for some power applications. In this article, I will discuss two methods of LM317 current boosting, using power PNP and NPN pass transistors.
According to the LM317 datasheet: “The LM317 [1, 2] device is an adjustable three-terminal positive-voltage regulator capable of supplying more than 1.5 A over an output-voltage range of 1.25 V to 37 V. It requires only two external resistors to set the output voltage. The device features a typical line regulation of 0.01% and a typical load regulation of 0.1%. It includes current limiting, thermal overload protection, and safe operating area protection. Overload protection remains functional even if the ADJUST terminal is disconnected.”
This information proves to us that this cheap 3-terminal device is suitable for many applications but it comes with a drawback for power applications and that is the limitation of the regulator’s output current handling (1.5A in the best conditions). This problem can be solved using a pass power transistor.
Current Boosting Using a PNP Power Transistor (MJ2955)
Figure-1 shows the schematic diagram of the circuit. This is an adjustable high current regulator circuit that the output voltage can be adjusted using a 5K potentiometer.
The 10R resistor defines the Turn-On time of the pass-transistor and by the way, it defines how much current should passe through the LM317 and MJ2955 [3, 4]. Based on this parameter, the power rate of the resistor must be calculated. 1N4007 is a protective diode and 270R resistor provides the necessary ADJ pin’s current. As mentioned earlier, the 5K potentiometer defines the output voltage. 1000uF, 10uF, and 100nF capacitors have used to reduce noises. Don’t forget to install the transistor on a big heatsink.
[A-2] Current Boosting Using an NPN Power Transistor (2N3055)
Figure-2 shows the schematic diagram of the circuit. The 10K resistor at the output draws a small amount of current to avoid the floating output and it helps to stabilize the output voltage. Here 2N3055 [5, 6] plays the role of pass-transistor also. LM317 Current Boosting Circuits [2N3055, MJ2955]](https://i.ytimg.com/vi/FItAwcsj0OI/mqdefault.jpg)






![How to Design the Component Libraries in Altium Designer [Beginners Tutorial]
How to Design the Component Libraries in Altium Designer [From Scratch]
Altium Designer + License (Free): https://www.altium.com/yt/myvanitar
In this video, you will learn (Altium Designer beginners tutorial) how to design/create a schematic symbol and a PCB footprint (a component library) in Altium designer and attach a 3D model to the footprint. Basically, you will create an integrated library and then you will add a schematic symbol and the PCB footprint. Then you are ready to compile the library and use it. My selected component is the LM358 opamp with the DIP8 package.
CHAPTERS
00:00 - Introduction
00:24 - 4 Methods of importing the component libraries in your PCB project
01:10 - How to design a Schematic symbol in Altium Designer
11:17 - How to design a PCB Footprint in Altium Designer
18:04 - How to add an external 3D model to the PCB footprint
20:30 - How to compile the integrated library and use the pre-build library
Music by Atch
SoundCloud: https://bit.ly/AtchSoundCloud
Spotify: https://bit.ly/AtchSpotify
Instagram: https://instagram.com/atchmusic How to Design the Component Libraries in Altium Designer [Beginners Tutorial]](https://i.ytimg.com/vi/J_pZdNdJaAs/mqdefault.jpg)