Uploaded October 2025 | Updated September 2026, 2 weeks ago
🧾 Description:
The new Bambu Lab P2S looks a lot like the X1C, but at a lower price. The question is: can it really replace it? In this video, I go through unboxing, setup, and calibration, then test it with various materials — from PLA and TPU to technical filaments like PET-CF, PPA-CF, and ASA-CF.
An important part of the test was to see if the P2S can handle brittle filaments, which often break inside some printers when bent too much.
🛒 Product link (affiliate): tidd.ly/4nHYkKa
💡 If you like my work, like the video or even support me on Patreon:
patreon.com/mytechfun
Mentioned in the video:
ChatGPT (generating Pop figure): chatgpt.com
STL Buddy (image to STL): stlbuddy.com
Owl: printables.com/model/743015-cute-low-poly-owl-no-supports
Wrench: printables.com/model/1440810-wrench-set-8mm-19mm
⏱️ Chapters:
0:00 Introduction
0:36 Specifications
2:32 Unboxing
6:32 Turning ON, calibration
7:40 Benchy, ventilation
9:22 Scraper
10:42 Screw gauge
11:17 Outer Radius gauge
11:42 Own Gcode, color printing
13:51 Single color PLA, timelapse
14:40 TPU
15:14 Bed level test (20 objects)
17:08 PET-CF
19:33 PPA-CF
20:34 ASA-CF
21:48 Conclusions
#BambuLab #P2S #3DPrinting #Review #mytechfun #X1C #EngineeringFilament #CarbonFiber #3DPrinterTest #BambuLabP2S
🧾 Description:
The new Bambu Lab P2S looks a lot like the X1C, but at a lower price. The question is: can it really replace it? In this video, I go through unboxing, setup, and calibration, then test it with various materials — from PLA and TPU to technical filaments like PET-CF, PPA-CF, and ASA-CF.
An important part of the test was to see if the P2S can handle brittle filaments, which often break inside some printers when bent too much.
🛒 Product link (affiliate): tidd.ly/4nHYkKa
💡 If you like my work, like the video or even support me on Patreon:
patreon.com/mytechfun
Mentioned in the video:
ChatGPT (generating Pop figure): chatgpt.com
STL Buddy (image to STL): stlbuddy.com
Owl: printables.com/model/743015-cute-low-poly-owl-no-supports
Wrench: printables.com/model/1440810-wrench-set-8mm-19mm
⏱️ Chapters:
0:00 Introduction
0:36 Specifications
2:32 Unboxing
6:32 Turning ON, calibration
7:40 Benchy, ventilation
9:22 Scraper
10:42 Screw gauge
11:17 Outer Radius gauge
11:42 Own Gcode, color printing
13:51 Single color PLA, timelapse
14:40 TPU
15:14 Bed level test (20 objects)
17:08 PET-CF
19:33 PPA-CF
20:34 ASA-CF
21:48 Conclusions
#BambuLab #P2S #3DPrinting #Review #mytechfun #X1C #EngineeringFilament #CarbonFiber #3DPrinterTest #BambuLabP2S
