Uploaded October 2021 | Updated November 2026, 2 days ago
In this video, I explore the differences between rigid and flexible bus bars. Using a FLIR camera, I run a ~54A, 10 minute load test, monitoring for heat differences in the two bus bar types.
The root of this video comes from a growing concern I have over vibration and movement in battery packs on vehicles, a boat in my case. Compressing, and to a lesser degree fixing the cells in place will help, but over the span of years it's unreasonable to expect no movement in the pack.
Given this, I worried about the long-term integrity of the bus bar to battery terminal junction. I wanted to see if there would be a noticeable difference if the rigid bus bars that came with the cells were replaced with flexible "bus bars" made from 4 awg marine wire.
Referenced videos;
@WillProwse - "Bloated LiFePO4 Cell Configuration to Reduce Terminal Stress!" - youtube.com/watch?v=iFKtIMkwlKA
@LithiumSolar - "LiFePO4 Battery Compression, Fixture, and Assembly - What's the Deal?" - youtube.com/watch?v=uZe6BDvWPfI
Fire - Note: This was NOT a Lifepo4 fire, I was mis-remembering. - diysolarforum.com/threads/devastating-fire.26841
More relevant article on poor battery connection resistance heating - sinovoltaics.com/learning-center/storage/incorrect-battery-connection-dangers
Chapters;
0:00 - Intro, Goals and Theories
2:58 - Test Descriptions
4:10 - Why I'm Not Compressing
5:28 - Making the Flexible Bus Bars / Jumpers
7:38 - A Kitty Interlude
8:50 - Crimper Tip
9:18 - Resistance Testing Flexible Bus Bars
12:05 - Resistance Testing Solid Bus Bars
13:30 - Resistance Test Summary
14:39 - BMS Balance Leads (re)Terminating
17:32 - Test Setup
22:00 - Solid Bus Bar Thermal Test
26:15 - Thermal Test Context (and Giddiness)
27:14 - Setting up for Flexible Test
29:12 - Flexible Bus Bar Test Start
31:25 - A Thermal Kitty Interlude
32:30 - A Winner! (In my opinion)
33:09 - A Request!
The bus bars were made using;
* Ancor Tinned Copper Battery Cable, 4 AWG (19mm²) - ancorproducts.com/en/p/113010/Tinned-Copper-Btery-Cable-4-AWG
* TE Connect 1/4" 4Awg Ring Terminals pn: 8-33469-2 - digikey.ca/en/products/detail/te-connectivity-amp-connectors/8-33469-2/2259482
* Crimped with a 35mm die, double-crimped to compress the entire barrel
In this video, I explore the differences between rigid and flexible bus bars. Using a FLIR camera, I run a ~54A, 10 minute load test, monitoring for heat differences in the two bus bar types.
The root of this video comes from a growing concern I have over vibration and movement in battery packs on vehicles, a boat in my case. Compressing, and to a lesser degree fixing the cells in place will help, but over the span of years it's unreasonable to expect no movement in the pack.
Given this, I worried about the long-term integrity of the bus bar to battery terminal junction. I wanted to see if there would be a noticeable difference if the rigid bus bars that came with the cells were replaced with flexible "bus bars" made from 4 awg marine wire.
Referenced videos;
@WillProwse - "Bloated LiFePO4 Cell Configuration to Reduce Terminal Stress!" - youtube.com/watch?v=iFKtIMkwlKA
@LithiumSolar - "LiFePO4 Battery Compression, Fixture, and Assembly - What's the Deal?" - youtube.com/watch?v=uZe6BDvWPfI
Fire - Note: This was NOT a Lifepo4 fire, I was mis-remembering. - diysolarforum.com/threads/devastating-fire.26841
More relevant article on poor battery connection resistance heating - sinovoltaics.com/learning-center/storage/incorrect-battery-connection-dangers
Chapters;
0:00 - Intro, Goals and Theories
2:58 - Test Descriptions
4:10 - Why I'm Not Compressing
5:28 - Making the Flexible Bus Bars / Jumpers
7:38 - A Kitty Interlude
8:50 - Crimper Tip
9:18 - Resistance Testing Flexible Bus Bars
12:05 - Resistance Testing Solid Bus Bars
13:30 - Resistance Test Summary
14:39 - BMS Balance Leads (re)Terminating
17:32 - Test Setup
22:00 - Solid Bus Bar Thermal Test
26:15 - Thermal Test Context (and Giddiness)
27:14 - Setting up for Flexible Test
29:12 - Flexible Bus Bar Test Start
31:25 - A Thermal Kitty Interlude
32:30 - A Winner! (In my opinion)
33:09 - A Request!
The bus bars were made using;
* Ancor Tinned Copper Battery Cable, 4 AWG (19mm²) - ancorproducts.com/en/p/113010/Tinned-Copper-Btery-Cable-4-AWG
* TE Connect 1/4" 4Awg Ring Terminals pn: 8-33469-2 - digikey.ca/en/products/detail/te-connectivity-amp-connectors/8-33469-2/2259482
* Crimped with a 35mm die, double-crimped to compress the entire barrel

![Ep. 91 - A Girl & Her Motor
This video is a long one, covering the wiring, pinout and initial power up of Mermaids Rests new heart!
We fix an electrical incompatibility between the Kelly Controller KLS-79100N and the Golden Motor 10kw that could have gone badly. The contactor, key switch and throttle are wired into the Kelly, and finally its powered up!
] References
* Kelly Controller and Golden Motor wiring and programming notes;
* https://docs.google.com/document/d/1qoHDtzcOTY1QK9pFImb2kukGdsc3yl-ahhXyBgp0OLk/edit?usp=sharing
* Crimping Tool Kit (NOT affiliated)
* https://www.amazon.ca/dp/B07R1H3Z8X?ref=ppx_yo2ov_dt_b_product_details&th=1
] Channels that have Helped Me;
* @ProjectBrupeg
* @OffGridGarageAustralia
* @AcornToArabella
* @BillCarlson
] Chapters
0:00 - Intro / Setting Expectations
1:47 - Golden Motor to Kelly Controller Incompatibility
4:11 - How Big Is This Problem?
5:34 - It’s Big; Madi Struggles With Pins
11:00 - Making Compatible Pinouts
14:39 - A Crazy Milestone!!
15:55 - Mid-Video Expectations
17:10 - Securing A Small Monster
18:15 - Pre-charge Resistor Redundancy
19:12 - Eating a Delorean One Bite At a Time
20:09 - Adding An In-Line Fuse
24:57 - Preparing a Stand-in Key Switch
27:52 - Learning to Make JST Connections
29:11 - DIY Helm Update
30:14 - Powering The Controller
32:01 - Old Battery Rebuild, Nerves and Mistakes
35:15 - Kitty Interlude
36:29 - A Third Near-Mistake!
39:08 - On Constructive Criticism and Naysayers
43:10 - Happy Design Accidents
44:12 - Finishing Up Power Wiring
50:47 - Connecting Control Wires
54:29 - I Missed a Wire…
56:39 - What To Do With The Throttle?
58:45 - No Jumping!
1:00:02 - Throttle Fault Protection
1:01:09 - Booting An Old, Annoying BMS
1:03:09 - First Controller Power Up!
1:05:28 - Initial Controller Config
1:07:01 - Identification Angle Routine Ep. 91 - A Girl & Her Motor](https://i.ytimg.com/vi/8jQ3imiTsdE/mqdefault.jpg)



![That Time I Crashed The Boat - Ep. 107
Happy Holidays! This is a bonus video with lost footage. On the trip home, I lost engine cooling, shut down the engine, and crashed into the rip-rap along the banks of the Erie Canal. I had a LOT of help from friends, and lost much of the footage of their help back when I was making the trip home videos.
So in the spirit of friends and family over the holidays, I wanted to finally make a bonus video out of that lost footage. Obviously, I made it home. So this is a video meant to highlight and celebrate the wonderful help I got from so many people. Especially though, Colin, Damien and Bruce!
] Patreon:
- https://www.patreon.com/TheDigitalMermaid
] Channels that have Helped Me;
* @ProjectBrupeg
* @OffGridGarageAustralia @OffGridGarageAustralia
* @AcornToArabella
* @BillCarlson
] References;
Ep. 58 - Preparing For The Trip Home
- https://www.youtube.com/watch?v=teA8mTtnEcE
] Chapters
0:00 - May 31, 2023
0:25 - Dec. 18, 2024
1:21 - I Crashed The Boat
4:00 - Damage Report
4:54 - What This Video is About
5:18 - Dangerous Assumptions
6:59 - All About Friends, Family and Strangers
9:04 - Erie Canal Helpers
10:53 - The Meaning of the Seasons
12:50 - Leading Up To The Breakdown
14:19 - Breakdown and Crash
16:54 - Clearing The Engine Seacock
21:48 - Damien Enters the Chat
24:49 - Time to Think Different
27:24 - Checking the Coolant Levels
29:44 - Pulling the Seawater Impeller
30:41 - Bruce Enters the Chat
32:08 - Shower Sump; Can I Use It?
33:58 - Kedging With a Danforth Sucks
37:24 - Preparing For The Morning
40:40 - The MacGyver Cooling Setup
43:53 - Were Ready To Go!
45:40 - We Made It!
] Music Attribution
Bad Ideas - Silent Film Dark by Kevin MacLeod is licensed under a Creative Commons Attribution 4.0 licence. https://creativecommons.org/licenses/by/4.0/
Source: http://incompetech.com/music/royalty-free/index.html?isrc=USUAN1100489
Artist: http://incompetech.com/
Avant Jazz - Disco Ultralounge by Kevin MacLeod is licensed under a Creative Commons Attribution 4.0 licence. https://creativecommons.org/licenses/by/4.0/
Source: http://incompetech.com/music/royalty-free/index.html?isrc=USUAN1100319
Artist: http://incompetech.com/
Classic Horror 1 - Dark World by Kevin MacLeod is licensed under a Creative Commons Attribution 4.0 licence. https://creativecommons.org/licenses/by/4.0/
Source: http://incompetech.com/music/royalty-free/index.html?isrc=USUAN1100471
Artist: http://incompetech.com/ That Time I Crashed The Boat - Ep. 107](https://i.ytimg.com/vi/AXJYUK8vKQg/mqdefault.jpg)




