Uploaded February 2024 | Updated November 2026, 1 day ago
This video is a long one, covering the wiring, pinout and initial power up of Mermaid's Rest's new heart!
We fix an electrical incompatibility between the Kelly Controller KLS-79100N and the Golden Motor 10kw that could have gone badly. The contactor, key switch and throttle are wired into the Kelly, and finally it's powered up!
-=] References
* Kelly Controller and Golden Motor wiring and programming notes;
* docs.google.com/document/d/1qoHDtzcOTY1QK9pFImb2kukGdsc3yl-ahhXyBgp0OLk/edit?usp=sharing
* Crimping Tool Kit (NOT affiliated)
* amazon.ca/dp/B07R1H3Z8X?ref=ppx_yo2ov_dt_b_product_details&th=1
-=] Channels that have Helped Me;
* @ProjectBrupeg
* @OffGridGarageAustralia
* @AcornToArabella
* @BillCarlson
-=] Chapters
0:00 - Intro / Setting Expectations
1:47 - Golden Motor to Kelly Controller Incompatibility
4:11 - How Big Is This Problem?
5:34 - It’s Big; Madi Struggles With Pins
11:00 - Making Compatible Pinouts
14:39 - A Crazy Milestone!!
15:55 - Mid-Video Expectations
17:10 - Securing A Small Monster
18:15 - Pre-charge Resistor Redundancy
19:12 - Eating a Delorean One Bite At a Time
20:09 - Adding An In-Line Fuse
24:57 - Preparing a Stand-in Key Switch
27:52 - Learning to Make JST Connections
29:11 - DIY Helm Update
30:14 - Powering The Controller
32:01 - Old Battery Rebuild, Nerves and Mistakes
35:15 - Kitty Interlude
36:29 - A Third Near-Mistake!
39:08 - On Constructive Criticism and Naysayers
43:10 - Happy Design Accidents
44:12 - Finishing Up Power Wiring
50:47 - Connecting Control Wires
54:29 - I Missed a Wire…
56:39 - What To Do With The Throttle?
58:45 - No Jumping!
1:00:02 - Throttle Fault Protection
1:01:09 - Booting An Old, Annoying BMS
1:03:09 - First Controller Power Up!
1:05:28 - Initial Controller Config
1:07:01 - Identification Angle Routine
This video is a long one, covering the wiring, pinout and initial power up of Mermaid's Rest's new heart!
We fix an electrical incompatibility between the Kelly Controller KLS-79100N and the Golden Motor 10kw that could have gone badly. The contactor, key switch and throttle are wired into the Kelly, and finally it's powered up!
-=] References
* Kelly Controller and Golden Motor wiring and programming notes;
* docs.google.com/document/d/1qoHDtzcOTY1QK9pFImb2kukGdsc3yl-ahhXyBgp0OLk/edit?usp=sharing
* Crimping Tool Kit (NOT affiliated)
* amazon.ca/dp/B07R1H3Z8X?ref=ppx_yo2ov_dt_b_product_details&th=1
-=] Channels that have Helped Me;
* @ProjectBrupeg
* @OffGridGarageAustralia
* @AcornToArabella
* @BillCarlson
-=] Chapters
0:00 - Intro / Setting Expectations
1:47 - Golden Motor to Kelly Controller Incompatibility
4:11 - How Big Is This Problem?
5:34 - It’s Big; Madi Struggles With Pins
11:00 - Making Compatible Pinouts
14:39 - A Crazy Milestone!!
15:55 - Mid-Video Expectations
17:10 - Securing A Small Monster
18:15 - Pre-charge Resistor Redundancy
19:12 - Eating a Delorean One Bite At a Time
20:09 - Adding An In-Line Fuse
24:57 - Preparing a Stand-in Key Switch
27:52 - Learning to Make JST Connections
29:11 - DIY Helm Update
30:14 - Powering The Controller
32:01 - Old Battery Rebuild, Nerves and Mistakes
35:15 - Kitty Interlude
36:29 - A Third Near-Mistake!
39:08 - On Constructive Criticism and Naysayers
43:10 - Happy Design Accidents
44:12 - Finishing Up Power Wiring
50:47 - Connecting Control Wires
54:29 - I Missed a Wire…
56:39 - What To Do With The Throttle?
58:45 - No Jumping!
1:00:02 - Throttle Fault Protection
1:01:09 - Booting An Old, Annoying BMS
1:03:09 - First Controller Power Up!
1:05:28 - Initial Controller Config
1:07:01 - Identification Angle Routine



![That Time I Crashed The Boat - Ep. 107
Happy Holidays! This is a bonus video with lost footage. On the trip home, I lost engine cooling, shut down the engine, and crashed into the rip-rap along the banks of the Erie Canal. I had a LOT of help from friends, and lost much of the footage of their help back when I was making the trip home videos.
So in the spirit of friends and family over the holidays, I wanted to finally make a bonus video out of that lost footage. Obviously, I made it home. So this is a video meant to highlight and celebrate the wonderful help I got from so many people. Especially though, Colin, Damien and Bruce!
] Patreon:
- https://www.patreon.com/TheDigitalMermaid
] Channels that have Helped Me;
* @ProjectBrupeg
* @OffGridGarageAustralia @OffGridGarageAustralia
* @AcornToArabella
* @BillCarlson
] References;
Ep. 58 - Preparing For The Trip Home
- https://www.youtube.com/watch?v=teA8mTtnEcE
] Chapters
0:00 - May 31, 2023
0:25 - Dec. 18, 2024
1:21 - I Crashed The Boat
4:00 - Damage Report
4:54 - What This Video is About
5:18 - Dangerous Assumptions
6:59 - All About Friends, Family and Strangers
9:04 - Erie Canal Helpers
10:53 - The Meaning of the Seasons
12:50 - Leading Up To The Breakdown
14:19 - Breakdown and Crash
16:54 - Clearing The Engine Seacock
21:48 - Damien Enters the Chat
24:49 - Time to Think Different
27:24 - Checking the Coolant Levels
29:44 - Pulling the Seawater Impeller
30:41 - Bruce Enters the Chat
32:08 - Shower Sump; Can I Use It?
33:58 - Kedging With a Danforth Sucks
37:24 - Preparing For The Morning
40:40 - The MacGyver Cooling Setup
43:53 - Were Ready To Go!
45:40 - We Made It!
] Music Attribution
Bad Ideas - Silent Film Dark by Kevin MacLeod is licensed under a Creative Commons Attribution 4.0 licence. https://creativecommons.org/licenses/by/4.0/
Source: http://incompetech.com/music/royalty-free/index.html?isrc=USUAN1100489
Artist: http://incompetech.com/
Avant Jazz - Disco Ultralounge by Kevin MacLeod is licensed under a Creative Commons Attribution 4.0 licence. https://creativecommons.org/licenses/by/4.0/
Source: http://incompetech.com/music/royalty-free/index.html?isrc=USUAN1100319
Artist: http://incompetech.com/
Classic Horror 1 - Dark World by Kevin MacLeod is licensed under a Creative Commons Attribution 4.0 licence. https://creativecommons.org/licenses/by/4.0/
Source: http://incompetech.com/music/royalty-free/index.html?isrc=USUAN1100471
Artist: http://incompetech.com/ That Time I Crashed The Boat - Ep. 107](https://i.ytimg.com/vi/AXJYUK8vKQg/mqdefault.jpg)





![Ep. 99 - So Many Switches; SPI, DMA and New Crew!
Meet the newest crew, Mae!
This video is an update to show whats been going on since the last video. We cover using shift registers over SPI to allow the helm to have many, many switches and drive many, many LEDs without needing a lot of I/O pins from the STM32.
We also look at how I have been working on wiring up the protoboards that will be used the next time we drive the motors.
] Patreon:
- https://www.patreon.com/TheDigitalMermaid
] Channels that have Helped Me;
* @ProjectBrupeg
* @OffGridGarageAustralia
* @AcornToArabella
* @BillCarlson
M-Helm Wiring v0.2
- https://docs.google.com/document/d/152Ps7UHdDhnzmMRyUrINmeGtiGbAAJLm2AB-EGysgY8/edit?usp=sharing
Wikipedia articles;
- Mae Jemison: https://en.wikipedia.org/wiki/Mae_Jemison
- SPI: https://en.wikipedia.org/wiki/Serial_Peripheral_Interface
- DMA: https://en.wikipedia.org/wiki/Direct_memory_access
- Shift Registers: https://en.wikipedia.org/wiki/Shift_register
] Chapters
0:00 - New Crew!!
0:53 - So Many Switches, So Few IO Pins
1:53 - SPI to the Rescue!
3:18 - DMA and So Many LEDs!
5:19 - From Rats Nest to Protoboards
9:34 - Coming Out of a Funk
11:46 - Who Rescued Who?
13:17 - How The Shift Registers Work (I think)
16:06 - Planning to Wire the Switchboard
19:01 - I Tell Lies
20:45 - Learning to Wire a Protoboard
31:46 - Thoughts On Prettiness
34:45 - Making Mistakes
37:07 - Learning From The Mistakes Ep. 99 - So Many Switches; SPI, DMA and New Crew!](https://i.ytimg.com/vi/C1mrix40oT8/mqdefault.jpg)
