Uploaded September 2024 | Updated November 2026, 1 day ago
Meet the newest crew, Mae!
This video is an update to show what's been going on since the last video. We cover using shift registers over "SPI" to allow the helm to have many, many switches and drive many, many LEDs without needing a lot of I/O pins from the STM32.
We also look at how I have been working on wiring up the protoboards that will be used the next time we drive the motors.
-=] Patreon:
- patreon.com/TheDigitalMermaid
-=] Channels that have Helped Me;
* @ProjectBrupeg
* @OffGridGarageAustralia
* @AcornToArabella
* @BillCarlson
M-Helm Wiring v0.2
- docs.google.com/document/d/152Ps7UHdDhnzmMRyUrINmeGtiGbAAJLm2AB-EGysgY8/edit?usp=sharing
Wikipedia articles;
- Mae Jemison: en.wikipedia.org/wiki/Mae_Jemison
- SPI: en.wikipedia.org/wiki/Serial_Peripheral_Interface
- DMA: en.wikipedia.org/wiki/Direct_memory_access
- Shift Registers: en.wikipedia.org/wiki/Shift_register
-=] Chapters
0:00 - New Crew!!
0:53 - So Many Switches, So Few IO Pins
1:53 - SPI to the Rescue!
3:18 - DMA and So Many LEDs!
5:19 - From Rats Nest to Protoboards
9:34 - Coming Out of a Funk
11:46 - Who Rescued Who?
13:17 - How The Shift Registers Work (I think)
16:06 - Planning to Wire the Switchboard
19:01 - I Tell Lies
20:45 - Learning to Wire a Protoboard
31:46 - Thoughts On Prettiness
34:45 - Making Mistakes
37:07 - Learning From The Mistakes
Meet the newest crew, Mae!
This video is an update to show what's been going on since the last video. We cover using shift registers over "SPI" to allow the helm to have many, many switches and drive many, many LEDs without needing a lot of I/O pins from the STM32.
We also look at how I have been working on wiring up the protoboards that will be used the next time we drive the motors.
-=] Patreon:
- patreon.com/TheDigitalMermaid
-=] Channels that have Helped Me;
* @ProjectBrupeg
* @OffGridGarageAustralia
* @AcornToArabella
* @BillCarlson
M-Helm Wiring v0.2
- docs.google.com/document/d/152Ps7UHdDhnzmMRyUrINmeGtiGbAAJLm2AB-EGysgY8/edit?usp=sharing
Wikipedia articles;
- Mae Jemison: en.wikipedia.org/wiki/Mae_Jemison
- SPI: en.wikipedia.org/wiki/Serial_Peripheral_Interface
- DMA: en.wikipedia.org/wiki/Direct_memory_access
- Shift Registers: en.wikipedia.org/wiki/Shift_register
-=] Chapters
0:00 - New Crew!!
0:53 - So Many Switches, So Few IO Pins
1:53 - SPI to the Rescue!
3:18 - DMA and So Many LEDs!
5:19 - From Rats Nest to Protoboards
9:34 - Coming Out of a Funk
11:46 - Who Rescued Who?
13:17 - How The Shift Registers Work (I think)
16:06 - Planning to Wire the Switchboard
19:01 - I Tell Lies
20:45 - Learning to Wire a Protoboard
31:46 - Thoughts On Prettiness
34:45 - Making Mistakes
37:07 - Learning From The Mistakes








![Setting The Pitch & Installing a Max-Prop Classic - BaB
This is a stand-alone video that shows how to set the pitch on a Max-Prop Classic propeller. It also covers the installation of the propeller on the shaft, and covers some of the possible complications you might run into.
] Patreon:
- https://www.patreon.com/TheDigitalMermaid
] Channels that have Helped Me;
* @ProjectBrupeg
* @OffGridGarageAustralia
* @AcornToArabella
* @BillCarlson
] References;
PYI - MaxProp Easy 3-Blade, 17
- https://store.pyiinc.com/products/max-prop-easy?sub-category=Max-Prop-Propellers&variant=4037589697
- @PYIinc
Max-Prop Classic Manual
- https://www.pyiinc.com/downloads/max-prop/max-prop-3-blade-classic-instructions.pdf
PYIs 3-Blade Classic Max-Prop Installation Instructions - Playlist
- https://www.youtube.com/watch?v=vICO2m0aHVk&list=PL8B01802857DFE0B4
] Chapters
0:00 - What Is This Video?
1:03 - Why Would You Change Your Pitch?
2:22 - What is Propeller Pitch?
4:09 - The Names of the Parts of the Propeller
5:14 - Making Sure The Key is Sized Properly
6:08 - The Pitch to Prop Angle Lookup Table
6:41 - The Handedness of Your Prop
7:14 - Determining Your X Configuration Letter
7:56 - Mating The Center Gear To The Hub
8:48 - What To Do If The Center Gear Doesnt Seat
9:51 - Woops, Forgot The Center Nut
10:33 - Installing The Nuts Locking Pins
12:12 - Installing The Spinner Halves
13:21 - Determining Your Y Configuration Letter
14:26 - Marking Your Y Configuration
14:59 - Putting The Blades On The Spacer
15:32 - Putting the Blade Assembly In The End Cap
16:34 - Connecting The Blades to The Hub
19:01 - Testing The Blade Rotation
19:49 - How To Grease The Prop
22:19 - Locking The Bolts With Cotter Pins
23:43 - Installing The Sacrificial Anode Setting The Pitch & Installing a Max-Prop Classic - BaB](https://i.ytimg.com/vi/FG7feNRWvWs/mqdefault.jpg)

![Happy Failures - Ep. 121
This video covers getting the replacement UFQFPN-32 version of the MCU soldered on. I cover what I had to check to see that it was compatible with the previous design.
I get the board mostly populated, and then try powering it up for the first time. It doesnt go well, but it also doesnt go badly, either. So Im considering this a happy bit of progress!
] Patreon:
- https://www.patreon.com/c/TheDigitalMermaid
] Channels that have Helped Me;
* @ProjectBrupeg
* @OffGridGarageAustralia
* @AcornToArabella
* @BillCarlson
] Chapters
0:00 - Coming Back From Disaster; UFQFPN vs LQFP
4:32 - On Comments and Feedback
5:28 - Leaded Solder; Why Im Not Using It
6:58 - Solder Iron Tip Size
7:39 - Flux Types And Concerns
8:28 - El Ejecto Syringo No Fixey. :(
9:54 - Soldering the UFQFPN 32 Package.... *eep*
13:12 - Testing The UGQFPN connections
15:26 - Onward To Through Hole Parts!
16:39 - Timelapse Assembly of Through-Hole Parts
18:35 - Assembly Update 1
20:49 - Assembly Update 2
22:27 - Power Plans, LED Standoffs and MRA Flux
24:06 - Finishing Assembly
25:28 - Final Checks For Shorts And Resistance
29:20 - As Ready As Can Be; Power Up!
30:20 - No Smoke! But No Life, Either. Why?
31:40 - High Voltage; Diagnosing With Andrew
33:49 - Happy Little Failure Happy Failures - Ep. 121](https://i.ytimg.com/vi/GNY8lcFv1zo/mqdefault.jpg)