Uploaded June 2023 | Updated November 2026, 1 day ago
In this second part, we get the AC power back online, and get shore power reconnected so we can charge the batteries.
patreon.com/TheDigitalMermaid
Channels that have Helped Me;
*@ProjectBrupeg
*@BillCarlson
*@OffGridGarageAustralia
*@LadyKSailing
*@AcornToArabella
0:00 - Intro
0:45 - Connecting the Multiplus
4:47 - A Change of Plans
6:20 - Temporary Multiplus Setup
9:10 - Madi Struggles With the Basics
11:02 - Madi Oopses, Madi is Tired
12:19 - Madi Struggles with a Cable
13:24 - AC From Batteries!
14:45 - A Rest Clears the Head
16:05 - Poor Person's Ferrules
18:45 - Connecting Shore Power
21:38 - Qualified Success
In this second part, we get the AC power back online, and get shore power reconnected so we can charge the batteries.
patreon.com/TheDigitalMermaid
Channels that have Helped Me;
*@ProjectBrupeg
*@BillCarlson
*@OffGridGarageAustralia
*@LadyKSailing
*@AcornToArabella
0:00 - Intro
0:45 - Connecting the Multiplus
4:47 - A Change of Plans
6:20 - Temporary Multiplus Setup
9:10 - Madi Struggles With the Basics
11:02 - Madi Oopses, Madi is Tired
12:19 - Madi Struggles with a Cable
13:24 - AC From Batteries!
14:45 - A Rest Clears the Head
16:05 - Poor Person's Ferrules
18:45 - Connecting Shore Power
21:38 - Qualified Success
![Ep. 99 - So Many Switches; SPI, DMA and New Crew!
Meet the newest crew, Mae!
This video is an update to show whats been going on since the last video. We cover using shift registers over SPI to allow the helm to have many, many switches and drive many, many LEDs without needing a lot of I/O pins from the STM32.
We also look at how I have been working on wiring up the protoboards that will be used the next time we drive the motors.
] Patreon:
- https://www.patreon.com/TheDigitalMermaid
] Channels that have Helped Me;
* @ProjectBrupeg
* @OffGridGarageAustralia
* @AcornToArabella
* @BillCarlson
M-Helm Wiring v0.2
- https://docs.google.com/document/d/152Ps7UHdDhnzmMRyUrINmeGtiGbAAJLm2AB-EGysgY8/edit?usp=sharing
Wikipedia articles;
- Mae Jemison: https://en.wikipedia.org/wiki/Mae_Jemison
- SPI: https://en.wikipedia.org/wiki/Serial_Peripheral_Interface
- DMA: https://en.wikipedia.org/wiki/Direct_memory_access
- Shift Registers: https://en.wikipedia.org/wiki/Shift_register
] Chapters
0:00 - New Crew!!
0:53 - So Many Switches, So Few IO Pins
1:53 - SPI to the Rescue!
3:18 - DMA and So Many LEDs!
5:19 - From Rats Nest to Protoboards
9:34 - Coming Out of a Funk
11:46 - Who Rescued Who?
13:17 - How The Shift Registers Work (I think)
16:06 - Planning to Wire the Switchboard
19:01 - I Tell Lies
20:45 - Learning to Wire a Protoboard
31:46 - Thoughts On Prettiness
34:45 - Making Mistakes
37:07 - Learning From The Mistakes Ep. 99 - So Many Switches; SPI, DMA and New Crew!](https://i.ytimg.com/vi/C1mrix40oT8/mqdefault.jpg)








![Setting The Pitch & Installing a Max-Prop Classic - BaB
This is a stand-alone video that shows how to set the pitch on a Max-Prop Classic propeller. It also covers the installation of the propeller on the shaft, and covers some of the possible complications you might run into.
] Patreon:
- https://www.patreon.com/TheDigitalMermaid
] Channels that have Helped Me;
* @ProjectBrupeg
* @OffGridGarageAustralia
* @AcornToArabella
* @BillCarlson
] References;
PYI - MaxProp Easy 3-Blade, 17
- https://store.pyiinc.com/products/max-prop-easy?sub-category=Max-Prop-Propellers&variant=4037589697
- @PYIinc
Max-Prop Classic Manual
- https://www.pyiinc.com/downloads/max-prop/max-prop-3-blade-classic-instructions.pdf
PYIs 3-Blade Classic Max-Prop Installation Instructions - Playlist
- https://www.youtube.com/watch?v=vICO2m0aHVk&list=PL8B01802857DFE0B4
] Chapters
0:00 - What Is This Video?
1:03 - Why Would You Change Your Pitch?
2:22 - What is Propeller Pitch?
4:09 - The Names of the Parts of the Propeller
5:14 - Making Sure The Key is Sized Properly
6:08 - The Pitch to Prop Angle Lookup Table
6:41 - The Handedness of Your Prop
7:14 - Determining Your X Configuration Letter
7:56 - Mating The Center Gear To The Hub
8:48 - What To Do If The Center Gear Doesnt Seat
9:51 - Woops, Forgot The Center Nut
10:33 - Installing The Nuts Locking Pins
12:12 - Installing The Spinner Halves
13:21 - Determining Your Y Configuration Letter
14:26 - Marking Your Y Configuration
14:59 - Putting The Blades On The Spacer
15:32 - Putting the Blade Assembly In The End Cap
16:34 - Connecting The Blades to The Hub
19:01 - Testing The Blade Rotation
19:49 - How To Grease The Prop
22:19 - Locking The Bolts With Cotter Pins
23:43 - Installing The Sacrificial Anode Setting The Pitch & Installing a Max-Prop Classic - BaB](https://i.ytimg.com/vi/FG7feNRWvWs/mqdefault.jpg)
