Gregs Maker Corner | Voron 0 Display Installation, Configuration and Features @GregsMakerCorner | Uploaded December 2021 | Updated October 2024, 12 hours ago.
In this video, I walk through the install, assembly, and Klipper configuration for the Voron 0 Display. My goal with this video is to provide all the steps in a relatively concise format from start to finish. This is a pretty straightforward upgrade, and I'd guesstimate you could do it in about an hour (or even less) once you have the parts printed. Cutting and crimping a USB cable adds time, but I think it's worth the effort and will give you the cleanest install.
Correction: The self tapping screws needed are 12mm, not 8mm. I didn't end up using them, and they are hard to source- so I'd say don't bother with them.
Special thanks to Steve Builds as well- I watched his Live Stream and took away a few ideas (like the JST-XH). I encourage you to check his video out for additional info.
youtube.com/watch?v=JJlL1S-_v0I
Scroll down to jump to specific areas:
0:36 - Walkthrough of Display Screen Features
2:48 - Parts Required
4:21 - Note about Heat Inserts
7:03 - Using a JST-XH for a clean install
7:50 - Installing heat Inserts
9:00 - Assembly of Screen into 3d Printed Parts
10:03 - Cutting a USB cable and crimping JST-XH connectors
15:06 - Powering up
15:12 - Getting device DFU ID
15:55 - Compiling Klipper
16:56 - Flashing Klipper to Voron 0 Display
17:20 - Confirming Klipper flashed
17:33 - Downloading DisplayEncoder.cfg from Github, and Uploading to Mainsail
18:17 - Adding an include line in Printer.cfg for DisplayEncoder.cfg
18:47 - Finishing up the install
19:57 - Summary and Conclusion
Main link to Voron 0 Display Github. You can find the STL's, Assembly Information, config file, etc. all from the Github. Scroll down for specific links as well.
github.com/VoronDesign/Voron-Hardware/tree/master/V0_Display
Direct Link to Klipper Install and Flashing Guide:
github.com/VoronDesign/Voron-Hardware/blob/master/V0_Display/Documentation/Setup_and_Flashing_Guide.md
Direct Link to STL's. I printed the knob, housing front, housing rear, (no usb option) and the single piece mount in the v0.1 folder.
github.com/VoronDesign/Voron-Hardware/tree/master/V0_Display/STLs
Direct link to DisplayEncoder.cfg:
github.com/VoronDesign/Voron-Hardware/blob/master/V0_Display/Software/DisplayEncoder.cfg
Where to buy?
Because of the chip shortage, it may be hard to find/source a display. Here are a few links to check.
I purchased mine here: fabreeko.com/products/ldo-voron-v0-display
DeepFriedHero: deepfriedhero.in/products/voron-v0-display
Aliexpress: aliexpress.com/w/wholesale-voron-v0-display.html
Printed Solid: printedsolid.com/products/ldo-voron-v0-display?variant=39319639162965
Example kit for the JST XH connectors needed:
aliexpress.com/item/4000126563819.html?spm=a2g0o.productlist.0.0.2add42caFjOO8u&algo_pvid=71fdcea7-ff1d-4bb2-9f47-50d8aa4f801c&algo_exp_id=71fdcea7-ff1d-4bb2-9f47-50d8aa4f801c-0&pdp_ext_f=%7B%22sku_id%22%3A%2210000000365693778%22%7D&pdp_pi=-1%3B0.69%3B-1%3BUSD+1.52%40salePrice%3BUSD%3Bsearch-mainSearch
Tools featured in my video are linked below. These are Amazon Affiliate Links. If you are considering buying a tool, please use my link- it costs you nothing extra, and helps me out. As an Amazon Associate I earn from qualifying purchases. Thanks for your support!
Engineer PA-09 Crimpers - amzn.to/3aLgZB9
Hakko 888FX High Quality Soldering Iron - amzn.to/3FZtsiM
Heat Insert Tips - amzn.to/3aLh6N5
Capri Wire Strippers - amzn.to/3ctPY62
Quick Reddit Post that is helpful on customizing the display menus::
reddit.com/r/klippers/comments/pbxloi/changing_lcd_menu_layout_in_klipper
In this video, I walk through the install, assembly, and Klipper configuration for the Voron 0 Display. My goal with this video is to provide all the steps in a relatively concise format from start to finish. This is a pretty straightforward upgrade, and I'd guesstimate you could do it in about an hour (or even less) once you have the parts printed. Cutting and crimping a USB cable adds time, but I think it's worth the effort and will give you the cleanest install.
Correction: The self tapping screws needed are 12mm, not 8mm. I didn't end up using them, and they are hard to source- so I'd say don't bother with them.
Special thanks to Steve Builds as well- I watched his Live Stream and took away a few ideas (like the JST-XH). I encourage you to check his video out for additional info.
youtube.com/watch?v=JJlL1S-_v0I
Scroll down to jump to specific areas:
0:36 - Walkthrough of Display Screen Features
2:48 - Parts Required
4:21 - Note about Heat Inserts
7:03 - Using a JST-XH for a clean install
7:50 - Installing heat Inserts
9:00 - Assembly of Screen into 3d Printed Parts
10:03 - Cutting a USB cable and crimping JST-XH connectors
15:06 - Powering up
15:12 - Getting device DFU ID
15:55 - Compiling Klipper
16:56 - Flashing Klipper to Voron 0 Display
17:20 - Confirming Klipper flashed
17:33 - Downloading DisplayEncoder.cfg from Github, and Uploading to Mainsail
18:17 - Adding an include line in Printer.cfg for DisplayEncoder.cfg
18:47 - Finishing up the install
19:57 - Summary and Conclusion
Main link to Voron 0 Display Github. You can find the STL's, Assembly Information, config file, etc. all from the Github. Scroll down for specific links as well.
github.com/VoronDesign/Voron-Hardware/tree/master/V0_Display
Direct Link to Klipper Install and Flashing Guide:
github.com/VoronDesign/Voron-Hardware/blob/master/V0_Display/Documentation/Setup_and_Flashing_Guide.md
Direct Link to STL's. I printed the knob, housing front, housing rear, (no usb option) and the single piece mount in the v0.1 folder.
github.com/VoronDesign/Voron-Hardware/tree/master/V0_Display/STLs
Direct link to DisplayEncoder.cfg:
github.com/VoronDesign/Voron-Hardware/blob/master/V0_Display/Software/DisplayEncoder.cfg
Where to buy?
Because of the chip shortage, it may be hard to find/source a display. Here are a few links to check.
I purchased mine here: fabreeko.com/products/ldo-voron-v0-display
DeepFriedHero: deepfriedhero.in/products/voron-v0-display
Aliexpress: aliexpress.com/w/wholesale-voron-v0-display.html
Printed Solid: printedsolid.com/products/ldo-voron-v0-display?variant=39319639162965
Example kit for the JST XH connectors needed:
aliexpress.com/item/4000126563819.html?spm=a2g0o.productlist.0.0.2add42caFjOO8u&algo_pvid=71fdcea7-ff1d-4bb2-9f47-50d8aa4f801c&algo_exp_id=71fdcea7-ff1d-4bb2-9f47-50d8aa4f801c-0&pdp_ext_f=%7B%22sku_id%22%3A%2210000000365693778%22%7D&pdp_pi=-1%3B0.69%3B-1%3BUSD+1.52%40salePrice%3BUSD%3Bsearch-mainSearch
Tools featured in my video are linked below. These are Amazon Affiliate Links. If you are considering buying a tool, please use my link- it costs you nothing extra, and helps me out. As an Amazon Associate I earn from qualifying purchases. Thanks for your support!
Engineer PA-09 Crimpers - amzn.to/3aLgZB9
Hakko 888FX High Quality Soldering Iron - amzn.to/3FZtsiM
Heat Insert Tips - amzn.to/3aLh6N5
Capri Wire Strippers - amzn.to/3ctPY62
Quick Reddit Post that is helpful on customizing the display menus::
reddit.com/r/klippers/comments/pbxloi/changing_lcd_menu_layout_in_klipper