Uploaded August 2026 | Updated November 2026, 5 days ago
A demo of what a UVC tube looks like when lit. They are a very pleasing ghostly blue, which unfortunately means that people have accidentally used them as a decorative item with painful results.
Everyone in the room had glasses on that blocked UVC. Most ordinary glasses and plastics will block it. It's actually harder to find materials that allow it to pass through.
We left the room for a while to allow the tube to come up to full power.
Note that defeating the safety shutter in a socket by shoving a metal key in the earth hole and then ramming bare wires into the live and neutral holes is not a recommended connection method, and poses a high shock risk.
UVC tubes are used for germicidal purposes in food processing equipment and in medical applications. There are two common types with different glass filtering properties. The classic germicidal tube only passes the 254nm wavelength from a mercury vapour discharge, but there are versions like this one that also pass the 184nm peak that breaks down oxygen bonds in air and allows temporary formation of short-lived active air molecules like ozone.
If humans or animals stare at a UVC tube it causes a temporary effect called photokeratitis which is the same painful effect experienced by being exposed to arc-welding flash (also strong UVC). There is a delay before the symptoms set in and it feels like sand in your eyes. But the discomfort will soon pass. If needed, medical intervention will offer a mild anaesthetic for the eyes to suppress the discomfort. A classic welders trick is to slice raw potato and apply the juice to the eyes - but I can't offer that as official medical advice.
High exposure can also cause surface damage to the skin, but contrary to a previous belief that it posed a risk of causing skin cancer, the UVC wavelength is so short that it can't pass deep enough into the skin to reach the critical areas. UVA and UVB pose a much higher risk in that area.
Two notable events where the organisers used high power UVC tubes as decoration were Hype-Beast and a "Bored Ape Yacht Club" event. Both resulted in high admissions to hospitals for skin and eye issues.
Other common accidental exposures are in the HVAC industry when workers open duct inspection panels where there are UVC tubes present, and when maintenance operatives accidentally use UVC tubes in place of the similar colour UVA ones in insect traps.
Most UVC tubes are identifiable by being clear glass instead of the white phosphor coated glass of traditional fluorescent tubes.
If you have a need for a small UVC germicidal tube then this one came from AliExpress, complete with an ungrounded fitting and internal ballast. Here's an affiliate link if you want one:-
https://s.click.aliexpress.com/e/_c2vyTqmB
If you do get one, make sure you store it in a box clearly marked with hazard warnings about UVC light.
A demo of what a UVC tube looks like when lit. They are a very pleasing ghostly blue, which unfortunately means that people have accidentally used them as a decorative item with painful results.
Everyone in the room had glasses on that blocked UVC. Most ordinary glasses and plastics will block it. It's actually harder to find materials that allow it to pass through.
We left the room for a while to allow the tube to come up to full power.
Note that defeating the safety shutter in a socket by shoving a metal key in the earth hole and then ramming bare wires into the live and neutral holes is not a recommended connection method, and poses a high shock risk.
UVC tubes are used for germicidal purposes in food processing equipment and in medical applications. There are two common types with different glass filtering properties. The classic germicidal tube only passes the 254nm wavelength from a mercury vapour discharge, but there are versions like this one that also pass the 184nm peak that breaks down oxygen bonds in air and allows temporary formation of short-lived active air molecules like ozone.
If humans or animals stare at a UVC tube it causes a temporary effect called photokeratitis which is the same painful effect experienced by being exposed to arc-welding flash (also strong UVC). There is a delay before the symptoms set in and it feels like sand in your eyes. But the discomfort will soon pass. If needed, medical intervention will offer a mild anaesthetic for the eyes to suppress the discomfort. A classic welders trick is to slice raw potato and apply the juice to the eyes - but I can't offer that as official medical advice.
High exposure can also cause surface damage to the skin, but contrary to a previous belief that it posed a risk of causing skin cancer, the UVC wavelength is so short that it can't pass deep enough into the skin to reach the critical areas. UVA and UVB pose a much higher risk in that area.
Two notable events where the organisers used high power UVC tubes as decoration were Hype-Beast and a "Bored Ape Yacht Club" event. Both resulted in high admissions to hospitals for skin and eye issues.
Other common accidental exposures are in the HVAC industry when workers open duct inspection panels where there are UVC tubes present, and when maintenance operatives accidentally use UVC tubes in place of the similar colour UVA ones in insect traps.
Most UVC tubes are identifiable by being clear glass instead of the white phosphor coated glass of traditional fluorescent tubes.
If you have a need for a small UVC germicidal tube then this one came from AliExpress, complete with an ungrounded fitting and internal ballast. Here's an affiliate link if you want one:-
https://s.click.aliexpress.com/e/_c2vyTqmB
If you do get one, make sure you store it in a box clearly marked with hazard warnings about UVC light.
![Hacking your Poundland solar garden lights (with 3D scripts)
Ive featured various hacks for making solar lights last longer, or for customising them. But its always worth revisiting.
This particular light is a classic Poundland light. Available in several case colours, but always with a horrible cold white LED. But fortunately they are fairly easy to customise with an LED colour of your choice.
This video also has an OpenScad script that allows you to make a custom base for attaching your lights to more suitable locations. You will find the script at the bottom of this description. I have added the customizer feature for your convenience.
Supporting the channel with a dollar or two on Patreon helps keep it independent of YouTubes quirks, avoids intrusive mid-video adverts, gives early access, bonus footage and regular quiet Patreon live streams.
https://www.patreon.com/bigclive
Alternatively, for a single coffee contribution you can use PayPal:-
https://www.paypal.com/paypalme/bigclive
#ElectronicsCreators
Here are THREE separate openscad scripts for making custom STL files for your preferred slicer. (A slicer converts a 3D object file into layers compatible with your 3D printer.)
Copy and paste the desired text below into openscad, an amazing free piece of software that lets you describe 3D objects. To enable the customizer, use the window menu to enable the customizer option. To see your creation quickly, press the double arrow button and to create your custom file press the hourglass button to create it, and then the STL button to save it.
Heres the version for vertical mounting:-
//Solar light post top base
//diameter of solar insert
dia=18;
//depth of collar
depth=16;
//screw hole diameter
screw=3.5;
//circle facets (100)
$fn=100;
difference(){
union(){
//base
cylinder(h=2,d=dia+22);
//collar
cylinder(h=depth,d=dia+2);
//strengthening taper
translate([0,0,2])
cylinder(h=2,d1=dia+6,d2=dia+2);
}
//hollow centre
translate([0,0,-1])
cylinder(h=depth+2,d=dia);
//screw holes
translate([-((dia /2)+7),0,-1])
cylinder(h=4,d=screw);
translate([(dia/2)+7,0,-1])
cylinder(h=4,d=screw);
}
This version is for angled mounting on a post or wall:-
//Solar light angled wall mount
//diameter of solar insert
dia=18;
//depth of collar
depth=30;
//screw hole diameter
screw=3.5;
//circle facets (100)
$fn=100;
difference(){
union(){
//base
cylinder(h=2,d=dia+24);
//collar
rotate([45,0,0])
translate([0,0,-(dia/2)])
cylinder(h=depth+dia,d=dia+2);
}
//hollow centre
rotate([45,0,0])
translate([0,0,-(dia/2)])
cylinder(h=depth+dia+2,d=dia);
//screw holes
translate([-((dia /2)+7),0,-1])
cylinder(h=4,d=screw);
translate([(dia/2)+7,0,-1])
cylinder(h=4,d=screw);
//underside cut-off cube
translate([-40,-40,-40])
cube([80,80,40]);
}
And one more version for a customisable bracket for mounting on a wall or the side of a post:-
//Solar light wall stand-off
//Diameter of solar base
dia=18;
//Height of bracket
high=20;
//Length of bracket
long=100;
//Screw hole diameter
screw=3.5;
//circle facets (100)
$fn=100;
difference(){
union(){
//wall plate
translate([0,-(dia+32)/2,0])
cube([3,dia+32,high]);
//stand off
translate([0,-((dia/2)+1),0])
cube([long-(dia+2)/2,3,high]);
translate([0,((dia/2)-2),0])
cube([long-(dia+2)/2,3,high]);
//collar
translate([long-(dia+2)/2,0,0])
cylinder(h=high,d=dia+2);
}
//hollow centre
translate([long-(dia+2)/2,0,-1])
cylinder(h=high+2,d=dia);
//screw holes
rotate([0,90,0])
translate([-high/2,-((dia+32)/2)+6,-1])
cylinder(h=5,d=screw);
rotate([0,90,0])
translate([-high/2,((dia+32)/2)-6,-1])
cylinder(h=5,d=screw);
} Hacking your Poundland solar garden lights (with 3D scripts)](https://i.ytimg.com/vi/3VU4MEviCAQ/mqdefault.jpg)









