Uploaded May 2026 | Updated November 2026, 3 hours ago
What are contacts in a PLC? The input instruction: normally-open passes power when a bit is on, normally-closed when it's off โ the condition on a rung. Here's how.
โก QUICK ANSWER
A contact is the input-side instruction in ladder logic โ it checks the state of a bit (an input, an internal relay, or an output) and passes power along the rung when its condition is met. There are two basic types. A normally-open contact passes power when its bit is ON โ it's "closed" (conducting) when the condition is true. A normally-closed contact is the inverse: it passes power when its bit is OFF, and opens when the bit turns on. You wire contacts together to build the logic on a rung โ in series for AND (all must be true) and in parallel for OR (any one true is enough) โ and that logic decides whether the coil at the end of the rung turns on. Contacts are half the foundation of ladder logic (coils are the other half). Here they're shown on the P1-M622-16DR. The full walkthrough is in the guide below.
๐ FULL WRITTEN TUTORIAL + DOWNLOADS (contact & coil instructions)
accautomation.ca/p1-m622-16dr-mini-plc-contact-and-coil-instructions
๐ WHAT YOU'LL LEARN
โ What a contact is โ the input-side instruction that conditions a rung
โ How a normally-open contact passes power when its bit is ON
โ How a normally-closed contact passes power when its bit is OFF
โ How contacts in series make AND logic and in parallel make OR logic
โ FREQUENTLY ASKED
Q: What is a contact in PLC ladder logic?
A: It's the input instruction that checks a bit's state and passes power along the rung when its condition is met โ the logic that decides whether the coil turns on. The full walkthrough is in the guide.
Q: What's the difference between normally-open and normally-closed contacts?
A: A normally-open contact passes power when its bit is ON; a normally-closed contact passes power when its bit is OFF โ the inverse.
Q: Can a contact check an output or internal bit, not just an input?
A: Yes โ a contact can reference any bit: a physical input, an internal relay, or even an output โ so you can use one rung's result as a condition in another.
๐ Full contact & coil guide: accautomation.ca/p1-m622-16dr-mini-plc-contact-and-coil-instructions
๐ MORE RESOURCES
โถ Series: accautomation.ca/series/productivity-plc
โถ Free ACC PLC Simulator (try contacts): accautomation.ca/simulator
โถ PLC Beginners Guide: accautomation.ca/programming/plc-beginners-guide
โถ Free eBooks: accautomation.ca (subscribe for download)
๐ RECOMMENDED HARDWARE
โถ Shop: automationdirect.com
โถ Parts Guide: accautomation.ca/purchase-find-parts
๐ฌ Questions? Drop a comment below.
๐ New tutorials every Monday โ Subscribe and hit the bell!
#PLC #LadderLogic #IndustrialAutomation #PLCProgramming #ACCAutomation #ProductivityPLC #AutomationDirect #Contacts #PLCBasics #Shorts
Regards,
Garry
ACC Automation
accautomation.ca
What are contacts in a PLC? The input instruction: normally-open passes power when a bit is on, normally-closed when it's off โ the condition on a rung. Here's how.
โก QUICK ANSWER
A contact is the input-side instruction in ladder logic โ it checks the state of a bit (an input, an internal relay, or an output) and passes power along the rung when its condition is met. There are two basic types. A normally-open contact passes power when its bit is ON โ it's "closed" (conducting) when the condition is true. A normally-closed contact is the inverse: it passes power when its bit is OFF, and opens when the bit turns on. You wire contacts together to build the logic on a rung โ in series for AND (all must be true) and in parallel for OR (any one true is enough) โ and that logic decides whether the coil at the end of the rung turns on. Contacts are half the foundation of ladder logic (coils are the other half). Here they're shown on the P1-M622-16DR. The full walkthrough is in the guide below.
๐ FULL WRITTEN TUTORIAL + DOWNLOADS (contact & coil instructions)
accautomation.ca/p1-m622-16dr-mini-plc-contact-and-coil-instructions
๐ WHAT YOU'LL LEARN
โ What a contact is โ the input-side instruction that conditions a rung
โ How a normally-open contact passes power when its bit is ON
โ How a normally-closed contact passes power when its bit is OFF
โ How contacts in series make AND logic and in parallel make OR logic
โ FREQUENTLY ASKED
Q: What is a contact in PLC ladder logic?
A: It's the input instruction that checks a bit's state and passes power along the rung when its condition is met โ the logic that decides whether the coil turns on. The full walkthrough is in the guide.
Q: What's the difference between normally-open and normally-closed contacts?
A: A normally-open contact passes power when its bit is ON; a normally-closed contact passes power when its bit is OFF โ the inverse.
Q: Can a contact check an output or internal bit, not just an input?
A: Yes โ a contact can reference any bit: a physical input, an internal relay, or even an output โ so you can use one rung's result as a condition in another.
๐ Full contact & coil guide: accautomation.ca/p1-m622-16dr-mini-plc-contact-and-coil-instructions
๐ MORE RESOURCES
โถ Series: accautomation.ca/series/productivity-plc
โถ Free ACC PLC Simulator (try contacts): accautomation.ca/simulator
โถ PLC Beginners Guide: accautomation.ca/programming/plc-beginners-guide
โถ Free eBooks: accautomation.ca (subscribe for download)
๐ RECOMMENDED HARDWARE
โถ Shop: automationdirect.com
โถ Parts Guide: accautomation.ca/purchase-find-parts
๐ฌ Questions? Drop a comment below.
๐ New tutorials every Monday โ Subscribe and hit the bell!
#PLC #LadderLogic #IndustrialAutomation #PLCProgramming #ACCAutomation #ProductivityPLC #AutomationDirect #Contacts #PLCBasics #Shorts
Regards,
Garry
ACC Automation
accautomation.ca










