The Silvertone Twin-Twelve Amplifier Restoration Project @retrotechandelectronics

Retro Tech & Electronics | The Silvertone Twin-Twelve Amplifier Restoration Project @retrotechandelectronics | Uploaded June 2019 | Updated October 2024, 1 day ago.
This is the compilation video of the six part restoration series of the Sears Silvertone Twin-Twelve model 1474. This is more of a non technical artistic condensed progression of this project which was. about 3.5 edited hours into about 14 minutes. Enjoy!

technocoma.blogspot.com

#tubeamp #restoration

Yamaha VSTAR 1100 Computer Assisted Carb Jetting & Tuning with an LM2 Computer

Chevy Cobalt Detailed Alternator Replacement in the Driveway

M&P Bodyguard 380 Reviewed - Unbox, Teardown, Rangetest, Cleaning

$The Dynaco Dynakit ST70 Stereo Amplifier Restoration Project Part 2 Now in Part 2 of the Dynakit ST70 restoration project, we will begin with the choke as the first component for installation, though I thought it interesting to compare both on the Genrad 1650A impedance bridge to see that the impedance and inductance is. SPEC 62ohms 1.75h OLD CHOKE 63ohms 1.50h NEW CHOKE 64ohms 1.35h All within acceptable range, the new choke is installed into the chassis, though, the old one is definitely a keeper for other projects. All work is done with the intent on maintaining a scratch free project and with extreme care. The tightening of all screws in this project has the slot of the screws pointing in the same direction. The two switches followed the choke and interestingly, they were not threaded like the original ones. This was helpful though and allowed the screw heads to maintain a parallel appearance. Following the switches was the assembly and installation of the gold plated input jack board. Returning to the old chassis, the selenium rectifier, power cable, fuse and stand-off board was removed for transfer. It became apparent that a custom screw for the rectifier would need to be fabricated. As these would be put into the new chassis it was also a good time to introduce the bias pots as well. Tightening in such a manner that the flats would be parallel to the font of the chassis. The rear jack kit was assembled at this point. This kit did not include the 16 ohm option, instead an internal standoff for 16ohm serving as a tie-off for the feedback connection. These are much better than the screws in the original kit. Upon assembly, these too are mounted. along with the end stand-offs. Returning from Lowes with a 6/32 screw the fuse socket was installed and the screw was cut as a rod in support of the selenium rectifier, using an acorn nut as the top cap. The standoff board was installed and then Id assembled some hardware to test the rectifier install. It looked good and was done so that the flat again was parallel to the chassis. The tube sockets were a little tricky because they are a bit smaller than the hole. So I had to shim it with two turns of paper to center the socket whilst tightening. It seemed to work good though. Mundane is having to repeat this several times. Moving to the power transformer was welcome. Its challenging though, guiding this heavy thing into the chassis without scratching anything with all of these wires everywhere. Somehow I managed to pull it off. Dampeners and all installed. Immediately I install for regular nuts on the bottom to hold the transformer in for safety. One benefit of the transformer is the ability to flip it to the service position. Power transformer wiring begins with the EL34 filaments, BROWN and GREEN. This included their center taps to the double capacitor to ground. Following this will be the connections to the rectifier. Then the primary black wires off of the power transformer to the fuse and switch. Following this, is the single cable to the selenium rectifier. At this point I go back to the old chassis to remove the star ground hardware and install it in the new chassis. The first connection to it would be the ground off of the power transformer. At this point a 3 prong power cable is introduced and wired in. The ground of this cable also meets the star ground. With the power testing is conducted with the Heathkit IM-11 VTVM using a fraction of the voltage. Switches are tested and then the ratios determine that the windings are ok. The center-taps to heaters were measured by resistance across the coil. Having completed this testing part 2, has come to an end. #dynaco #st70 #tubeamplifier #antique #restoration$

DIY Ultra Low Power Soil Moisture Monitor with an ESP32 using Arduino IDE

Hayward Star Clear Plus Filter Maintenance Hints and Tips

First Project ESP32 development using the TTGO T-DISPLAY

ESP32 Automated Irrigation Control System Project - PART 5 - System Demonstration

Maytag Whirlpool Refrigerator Door Seals Replaced in Fridge and Freezer

ESP32 and Arduino - MAX6675 Thermocouple Tests and Experiments

Roomba I7+ Simple Maintenance for Optimum Performance