Retro Tech & Electronics | Hayward Star Clear Plus Filter Maintenance Hints and Tips @retrotechandelectronics | Uploaded July 2020 | Updated October 2024, 1 day ago.
In one of my last videos i'd discussed the renovation of the pool pump/filter area in the yard. Now we had opened the area for daily use, having run everything for a few months already. Today attention is focused on the pool pump itself.
For safety, we start with cutting power on the main breaker. Followed by opening the air valve so that it will be easier to remove the cover. Twisting off the top screw releases the top cover which is lifted off, allowing the filter to be lifted out.
The canister is easily washed out to remove debris. Then focus is brought to the filter element. The best technique I've found is demonstrated in the video for doing so. If its beyond repair, comparisons for replacements are pointed out. I've fared better with the nylon mesh bags on the pickup basket over the years and continue to use those.
The filter, cleaned is seated back into the unit, O-ring lube is applied to the rubber ring around the cover. With the gauge in the correct direction, the knob is re-tightened. Finally, the air valve is closed, and power is re-applied.
The pump is turned back on, and we await priming, also checking for leaks. Satisfied there are no leaks, the air is purged from the valve up top.
I also quickly demonstrate how to open the pump without the entire system draining back if you have this type of setup.
Jandy Valve
amzn.to/3ldhZH6
#hayward #poolpump #poolfilter
In one of my last videos i'd discussed the renovation of the pool pump/filter area in the yard. Now we had opened the area for daily use, having run everything for a few months already. Today attention is focused on the pool pump itself.
For safety, we start with cutting power on the main breaker. Followed by opening the air valve so that it will be easier to remove the cover. Twisting off the top screw releases the top cover which is lifted off, allowing the filter to be lifted out.
The canister is easily washed out to remove debris. Then focus is brought to the filter element. The best technique I've found is demonstrated in the video for doing so. If its beyond repair, comparisons for replacements are pointed out. I've fared better with the nylon mesh bags on the pickup basket over the years and continue to use those.
The filter, cleaned is seated back into the unit, O-ring lube is applied to the rubber ring around the cover. With the gauge in the correct direction, the knob is re-tightened. Finally, the air valve is closed, and power is re-applied.
The pump is turned back on, and we await priming, also checking for leaks. Satisfied there are no leaks, the air is purged from the valve up top.
I also quickly demonstrate how to open the pump without the entire system draining back if you have this type of setup.
Jandy Valve
amzn.to/3ldhZH6
#hayward #poolpump #poolfilter
![Sears Silvertone Twin Twelve 1484 Major Restoration Project [5/6]](https://i.ytimg.com/vi/vfQnLG_yjMQ/hqdefault.jpg "Sears Silvertone Twin Twelve 1484 Major Restoration Project [5/6]
We continue into part five with some of the cosmetic work, beginning with the prep and painting of the handle ends so that they can be re-installed into the cabinet. This gives pause and time to reflect on how far things have come since the beginning of the project. With that, everything is placed back into the cabinet and screwed back in. The top caps for the handle are snapped back in and everything receives and inspection.
This starts the disassembly of the speaker cabinet for repairs and restoration. This will need a lot of work. Much water damage, pieces missing that will require research as well. Chunks of corners are gone and a deep cleaning will be required before anything else.
Having cut back a section of inside material, repairs begin throughout the amp from easiest to hardest. Most sections roughed up upon completion to match the patina around the affected area. Corners were built back up with putty first.
On the inside there will need to be repairs to the bottom that has been rotted out by water damage. A clear glue will be soaked into the wood and let to settle overnight to turn it back into plywood and then knocked down flat again and filled with wood putty. The second sanding with the putty preps it for stain and polyurethane.
The cabinet handle end prep work is done the same way as the one for the amp cabinet. Once completed the handle is re-introduced to the speaker cabinet.
We did a visit to Hobby Lobby to find material for the sides and ended up with a 3in elastic belt to do the job and it came out perfect. Having been given a picture of the original setup I was able to replicate it.
One piece of speaker cable is chewed up in the 1st two feet so it was simply removed as to not cause issues later. With that the back of the cabinet was replaced and the Tolex received a final treatment.
The remaining belt material is glued to the backstops to protect the amp, the Amplifier then reinserted into the cabinet to see how it fits. Everything looks really nice. Cable management wasnt too bad either.
At this point I turn the Amp over to the wife for testing. sadly there were issues. Though the Amp itself ran great, troubleshooting shows that the speakers within the cabinet have issues. This proved to be conclusive and we proceeded with a demo of the amp using a different speaker and relegated the cabinet speaker repair to the next unscheduled video, part 6.
#retrotechandelectronics #vintagetubeamprepairs")
