Uploaded October 2016 | Updated November 2026, 18 hours ago
Solid Potassium Nitrite was added to Silver Nitrate solution. Immediately the insoluble white Silver Nitrite precipitates. Any yellow hue is due to the formation of Silver Oxide (Ag2O) which forms as well. As more Nitrite is added the solution becomes much clearer (hard to see on cam unfortunately).
Literature always mentions a complex which forms in excess Nitrite. We were unable to find out more about this complex but found a dissociation constant for a [Ag(NO2)2](-) complex. As Ag(I) prefers linear coordinations and we know Ag-N bonds from the soluble Diammine complex for example or Ag-NO3 as soluble compound the Ag-NO2 complex seems plausible.
Solid Potassium Nitrite was added to Silver Nitrate solution. Immediately the insoluble white Silver Nitrite precipitates. Any yellow hue is due to the formation of Silver Oxide (Ag2O) which forms as well. As more Nitrite is added the solution becomes much clearer (hard to see on cam unfortunately).
Literature always mentions a complex which forms in excess Nitrite. We were unable to find out more about this complex but found a dissociation constant for a [Ag(NO2)2](-) complex. As Ag(I) prefers linear coordinations and we know Ag-N bonds from the soluble Diammine complex for example or Ag-NO3 as soluble compound the Ag-NO2 complex seems plausible.
. As with almost all Pd(II) compounds the Iodopalladate(II) is a square-plane again.
At the end I place my hand behind the glass so you can see that it actually turned transparent as the cam doesnt pick it up that well. Palladium Chemistry: Tetraiodopalladate(II)](https://i.ytimg.com/vi/JGVemyRbRJw/mqdefault.jpg)




 and [Cu(H2O)5](2+) once more water is present the color changes to blue which is why the solution becomes colorless. If we had reduced it at that time we might have been able to form Cassius gold which is purple.
The last question is why the yellow-green color is so intense while the water one is colorless. This has to do with two things. First the conc. becomes smaller as more water is added diluting the intensity and on the other hand if we assume [CuCl4](2-) forms this is a tetrahedral complex while [Cu(H2O)5](2+) is octahedral, with some Jahn-Teller distortion of course. Often tetrahedral complexes tend to be much more intense in color as they do not possess an inverse symmetry. The lack of inverse symmetry influences the parity of the t2 and e, the split orbital sets used for coordination chemistry.
Absorption of light on the matter goes with the change of the dipole moment which is an odd function. And by absorbing photons you excite electrons which then jump between two energy levels (t2 and e). Those can be odd or even in parity. The overall process is the product of all three meaning it is either odd or even while according to quantum mechanics the probability of something is the square of the integral of the total space. Integrating an odd function like x³ will always lead to zero making it impossible. Problem is that complexes with inverse symmetry like the octahedral ones have a t2g and eg so both lower and higher energy level have the same parity.
The reason why we usually still see some color is because the ligands that form the octahedron have some movement as well and they do not move all synched. So the perfect symmetry is destroyed making it colored again.
And the last reason why the yellow-green is just more intense might be because some of the NO-gases formed also dissolve in water and color it brown-orange. Adding more water dissolves it to Nitrous acid. Gold Chemistry: Gold in Aqua Regia](https://i.ytimg.com/vi/KyhEi8vIn8Y/mqdefault.jpg)
![Manganese Chemistry: Cyanomanganate(II/III) and K[Mn(CN)3]
1) Mn(II) added to conc. KCN solution, then air bubbled through
2) Mn(II) added to low concentration of KCN then air bubbled through.
Explanation will come soon ! Manganese Chemistry: Cyanomanganate(II/III) and K[Mn(CN)3]](https://i.ytimg.com/vi/L5HdES4gB1g/mqdefault.jpg)
, so the analogue to the yellow Ferrocyanide. We tried it with a huge excess of Cyanide and it would only turn green. So we had the idea to also add a bit of acid. The reason to why we did this is further explained in our RuCl3-solution video. As the acid was added it turned blue then colourless.
Literature says that a Cyanoruthenate(III) exists as well as slightly yellow compound. So we left a part of the solution open for two weeks and it turned slightly yellow in that time (end of the video). Strong acids are said to precipitate Ru(CN)3 from this.
About the blue compound that formed in between:
When we did this experiment the first time we used a solution of RuCl3 in a bit of HCl we had already prepared a few weeks earlier. The reason to this was that we expected it to become more reactive as in that time the tightly bound Chloride ligands might eventually exchange for more reactive aqua ligands. As it turns out whatever species may form in this time (this depends on the actual composition of the “RuCl3”) reacts completely different from a freshly prepared solution. When we did this experiment and heated it it turned blue. We might upload the video once we find out what actually happened. So we looked it up and found only one possible idea, mentioned in the literature a long time ago and never really tested again, a Ru2(CN)5H2O. This blue compound is said to form in hydrochloric acid and it seems to be blue. So we used some of the colourless solution and added it to a bit of acidified RuCl3 and after a day it was blue as well.
What we think happens is the following: Hexacyanoruthenate(II) and (III) undergo a quick ligand exchange which is accelerated by a reduced pH value to yield [Ru(CN)5(H2O)](3-). This might react with unreduced Ru(III) in solution (if the conc of Cyanide is too low or the RuCl3 is added later when the mixture is cold) and it could be analogous to Prussian Blue.
What we think happens in the reaction is the following. We also tried to add the acid first and then the Cyanide and it produced a lot of HCN before the Cyanide could even reach the bottom of the tube while the other way around didn’t produce much gases. So we believe that the Cyanide and RuCl3 in fact reacted at elevated temperatures but some Ru(IV)-species (for example) which is present in commercial RuCl3, or better just call it insoluble rests either wasn’t fully dissolved yet or not reactive enough. When the acid was added this unit broke apart the colourless Cyano complex formed. But this also induced the other reaction which forms the blue compound. This seems to build up as intermediate and is then reduced as the rest of Ru(III) in the complex is reduced to colourless Ru(II).
If you have any suggestion to what it is we would be happy for any answers. As mentioned before it’s hard to find anything on this topic. Many compounds have been postulated but never tested afterwards. Ruthenium Chemistry: Cyano-Ruthenate (II/III)](https://i.ytimg.com/vi/L7RRZ6esZlY/mqdefault.jpg)

If Silver meets Chloride insolbule Silver Chloride is formed. This can be dissolved again using Ammonia solution which formed the transparent [Ag(NH3)2](-) complex. Silver Chemistry: AgCl2 and [Ag(NH3)2](-)](https://i.ytimg.com/vi/LM6y9maUL68/mqdefault.jpg)

