Uploaded September 2026 | Updated November 2026, 3 hours ago
laptopscreen.com
laptopscreen.com/English/model/ASUS/X515MA
This is a guide on replacing a screen on Asus X515MA-Ts91-CB laptop. To begin shut down the
laptop and disconnect the power cord.
First step is to remove the bezel. The bezel is held in place with two Phillips screws in the bottom
corners and tabs around the perimeter. The screws are covered with two tiny plastic covers.
Using a X-Acto Knife remove the plastic covers. Using Phillips screwdriver remove two screws
in the bottom corners. Insert a plastic pick between the bezel and the LCD screen on the inner
side. Move the pick along the edge. Insert a plastic pick between the bezel and the back cover.
Go around the perimeter. Release the screen near the bottom. Turn the laptop sideways.
And release the bezel at the bottom. Put the bezel aside.
The LCD screen is glued to the rails and the back cover. Remove the two screws in the top
corners to get easier access to the screen. Separate the screen from the rails and the back cover
and place it on the keyboard. Peel off the first tape securing the video connector.
Then second clear tape. Then using both hands disconnect the video cable. Discard the old
screen.
Place the new screen on the keyboard. Reconnect the video cable. Secure it with clear tape,
then second piece of tape
CAUTION! It is very important not to force any connectors. As well you must not twist or slant the
connector when plugging it in.
Now we can test the screen. Reconnect the power cord and turn the laptop on. The screen is
working and we can finish the installation process.
Place the screen back at the keyboard. Replace the two screws at the top corners. We are going
to use a set of adhesive strips which you can buy on our site laptopscreen.com Apply adhesive strips.
Remove protective film. Lift the screen up and apply some pressure to catch the adhesive. Remove
the protective film from the new screen.
We are going to use 3mm adhesive tape to support the bezel. You which you as well buy on our
site laptopscreen.com Apply the piece of adhesive strip at the bottom of the screen. Replace the
bezel. Go around the perimeter snapping the tabs back in place. Turn the laptop sideways and
make sure that the bezel is snapped in the bottom. Replace two Phillips screws at the bottom of
the screen. Replace two plastic covers. Reconnect the power cord. Turn the laptop on.
And we are done!
laptopscreen.com
laptopscreen.com/English/model/ASUS/X515MA
This is a guide on replacing a screen on Asus X515MA-Ts91-CB laptop. To begin shut down the
laptop and disconnect the power cord.
First step is to remove the bezel. The bezel is held in place with two Phillips screws in the bottom
corners and tabs around the perimeter. The screws are covered with two tiny plastic covers.
Using a X-Acto Knife remove the plastic covers. Using Phillips screwdriver remove two screws
in the bottom corners. Insert a plastic pick between the bezel and the LCD screen on the inner
side. Move the pick along the edge. Insert a plastic pick between the bezel and the back cover.
Go around the perimeter. Release the screen near the bottom. Turn the laptop sideways.
And release the bezel at the bottom. Put the bezel aside.
The LCD screen is glued to the rails and the back cover. Remove the two screws in the top
corners to get easier access to the screen. Separate the screen from the rails and the back cover
and place it on the keyboard. Peel off the first tape securing the video connector.
Then second clear tape. Then using both hands disconnect the video cable. Discard the old
screen.
Place the new screen on the keyboard. Reconnect the video cable. Secure it with clear tape,
then second piece of tape
CAUTION! It is very important not to force any connectors. As well you must not twist or slant the
connector when plugging it in.
Now we can test the screen. Reconnect the power cord and turn the laptop on. The screen is
working and we can finish the installation process.
Place the screen back at the keyboard. Replace the two screws at the top corners. We are going
to use a set of adhesive strips which you can buy on our site laptopscreen.com Apply adhesive strips.
Remove protective film. Lift the screen up and apply some pressure to catch the adhesive. Remove
the protective film from the new screen.
We are going to use 3mm adhesive tape to support the bezel. You which you as well buy on our
site laptopscreen.com Apply the piece of adhesive strip at the bottom of the screen. Replace the
bezel. Go around the perimeter snapping the tabs back in place. Turn the laptop sideways and
make sure that the bezel is snapped in the bottom. Replace two Phillips screws at the bottom of
the screen. Replace two plastic covers. Reconnect the power cord. Turn the laptop on.
And we are done!










